similar to: wink time

Hi list, Sometimes I receive a Red Alarm in my E1 trunk (E&M immediate start signaling), and just few seconds after this, all alarms are cleared. This problem ocurrs many times/day, and if are calls in progress, these calls just hang-up. Could it be an asterisk bug? Or may I contact the PSTN provider? Thanks Eduardo

Hi, Has anyone got the X100P to work with an anlogue line in the Republic of Ireland? I have the X100P installed but zttool indicates a Red Alarm status on the card. It is on its own interrupt and I have tried different PCI slots but all to no avail. Are there any alternatives to the X100P that can work with asterisk and are likely to work in Ireland? Thanks, Aaron

Hi, I suspected that I the analogue phone should have got a pass through signal when the power was off to the server, unfortunately it doesn't. I kept asking digium support about that but they didn't give me an answer. The problem is how do I identify whether the X100P is incompatibel with the network or faulty without possibly wasting another USD100??? Aaron On Sat, 2004-05-15, Eric

Just noticed that no matter what the line condition is, zttool always reports "OK", so it's pretty useless. (In contrast, I'd get "Red alert" if I unplug the line connecting to an X100P.) I'm using zaptel 1.2.15 on Linux 2.6.15-28 (also tested on 2.6.10). Yuan Liu

Greetings and I thank you in-advance, I have a system installed with both Trixbox 1.x and 2.x installed and I am trying to utilize a wildcard x100p but it does seem hang-up or release the line. I understand that the Wildcards are not recommended, but I need to get a test system up for evaluation. Here are the steps followed: Run genzaptelconf and red alarm appears in zttool Run again and it

SYNOPSIS Erratic red alarm T1 PRI on asterisk, but zttool running concurrently during alarm shows no errors, irq misses, or alarms, on any span. Using asterisk and quad Digium T405P, configured as follows: Span 1 connects to ISDN PRI (fractional 8 B channels, D channel 24). Span 2 connects to T1 Mux and analog stations. Span 3 connects to ISDN PRI Nortel BCM hybrid key system digital trunk.

Could anyone with any experience with * over a non-PRI T1 help this newbie? I have a fractional T1 that is working fine through a channel bank, but I can't get any response on * using a T400P. My analog line and the extensions work fine, but the T400P port 1 shows a red led (what exactly does that tell me?). I brought up zttool which shows a condition red also, but ztcfg shows nothing amiss.

I am preparing to connect an asterisk box with a redfone fonebridge to a T1 service provider. I am doing this by testing first with another asterisk and a Sangoma card playing the role of telco. I formerly had this test configuration operating flawlessly as a PRI connection. But I discovered that I will need to use E&M, thus I've chosen the parameters as described in the subject

Hi, I've just added an X101P FXO card to my asterisk machine. The card is detected ok but zttool always shows it in a RED alarm state, which I understand means that it doesn't detect the line. I've connected the card via the line socket to my analogue line using the cable that came with the card (and have also tried other cables too) but I always get a RED alarm. I'm located in

Is there a configuration difference for clone X100P cards versus "compatible"? I have a similar problem to what David Shaw posted earlier today. 0.5 installed OK, but mine just with one X100P clone. Default config files, edited zapata.conf per the FAQs so it includes the line channel => 1 without the semicolon. Any outgoing call attempt returns "all circuits are busy"

Hi, I have an ansterisk and a cisco 827-4v registered to a Gatekeeper. asterisk has two extensions: exten => 223,1,Dial,OH323/BYEXTENSION@827PD exten => 730,1,Dial(IAX/eduardo@10.0.11.103) (IAX are working well) When I try to call each other, gnugk shows a ARJ: ARJ|10.0.11.112:1720|223:dialedDigits|730:dialedDigits|false|resourceUnavailable I think this could be a codec

Hi list, I'm trying to set up a TDM40B, but modprobe returns the fowling errors: asterisk:~# modprobe wcfxs ZT_CHANCONFIG failed on channel 1: Invalid argument (22) /lib/modules/2.4.18/misc/wcfxs.o: post-install wcfxs failed /lib/modules/2.4.18/misc/wcfxs.o: insmod wcfxs failed Could someone give me a help? Thanks in advance Eduardo

Hello All, I have got my TE110P working at the hardware level, turned out to be a dodgy cable causing the Yellow errors in zttool. However, now I am getting yellow errors in asterisk, but zttool shows nothing out of the ordinary. here is my current config, and some asterisk console errors, any suggestions most welcome. zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31

We are having line noise issues in our Asterisk to legacy PBX integration. All SIP calls originating from IP phones sound crystal clear. All calls that originate from the legacy PBX (Isoetec 228) and route through the Asterisk and out SIP have a lot of line noise. I believe I have it pinned down to these Blue Alarm errors that I can see on the legacy PBX side. zttool shows no alarm but when I

Hi all I'm trying to configure a TE410P in Europe with three E1s and a T1 channel bank (already bought in the US) to receive and make calls through *. I managed to get the E1s to work, but I'm having trouble with the channel bank (a Rhino). I have tried the bank in spans 1 and 4 changing jumpers in the card (always with no PRI connected, as I have no PRI where I'm testing now,

Hi Does anybody if the X100P works in Switzerland? We can't get a line to PSTN. When I run zttool it shows me always a red alert. I can make and receive calls with an anlog phone plugged in the phone connector. I've compiled and configured the card according to the wiki. Everything seemed to be ok. Is there a way to debug this? Regards Reto

A customer of mine has 3 TDM400P cards in a box running asterisk. On each card he has four FXO modules. I have set up the dialplan to dial via group 1 for an outgoing call. Channels 1-12 are in group 1. If he plugs a telephone cable into socket 2 or 3 etc, but not 1, when he dials out, it still tries to make the call via socket 1. Straight away the console says that it has dialed the

I have configured TDMoE sucessfully and I am able to make a Zap connection from one box to the other. The question I have is.. I'm getting repeated errors every second on both systems.. Oct 3 09:53:16 WARNING[4409]: chan_zap.c:6252 handle_init_event: Detected alarm on channel 1: No Alarm Oct 3 09:53:16 WARNING[4409]: chan_zap.c:6252 handle_init_event: Detected alarm on channel 2: No Alarm

Hello, I have some problem to start asterisk. First I have followed a lot of tutorials to complete correctly the install process. Now it works when I type zttool I can see when I am or not connected to the PSTN. But, I run asterisk with vvvv verbose and I can't see the call detection. There is no detection of the call. I have a X100P card FXO with only one line. So only one channel I

Thought I would post this experience to the list so it's archived for posterity... My company is deploying Asterisk-based PBX's to all of our branch offices. Each office has 2 analog Voice lines and a fax line. We didn't want to go to the expense of using TDM400's in the servers (which run asterisk and Hylafax) so we opted for 2 X100P cards in each box. So far they have