similar to: Lucent and ISDN-PRI

Hi everyone, We have been working with Asterisk for a while now and would really like to expand its capabilities by fully integrating it with our Definity g3si and are wondering about other peoples experiences with similar setups. Thus far we have only been able to achieve a partial 1 way integration, but ultimately would love to route inbound voip calls to the asterisk out of the lucent.

We have had quite a bit of success with our T100P and TE410P cards interfacing to Nortel Meridian PBXes and also to a Livingston Portmaster 3 using ESF/B8ZS and various combinations of E&M wink and ISDN PRI (usually in 5ESS mode). In the near future, I may also need to interface to a Definity via a T1. I was planning to use PRI--is that an option for you on your switch? -----Original

I have an asterisk with a TE110P configured as T1 which is behind a PSTN gateway. This gateway has an E1 to PSTN and a T1 to asterisk. This T1 is configured as Network and * as CPE. Every call I receive in E1 gateway is directly switched to asterisk using T1. Remember E1 is alaw. Both E1 and T1 have Natural Microsystems boards with a very simple software. When I call to E1 asterisk signalling

I've been working on an asterisk box at work for a few weeks now, things were finally starting to sail smoothly until I hit this head scratcher this morning. It's a rather intricate problem, so bear with me. Heres the scenario. What works: If I call from my sip phone -> sip phone everythings ok If I call from sip phone -> external pots number ok as well If I map one of our

Hi all, Can somebody help me out, to get the call going through to my provider? I connected my A104D Sangoma card to E1/isdn and each I tried to make call I get the errors below. My protocol analyzer can see only setup info and release complete. WIRELESS2*CLI> set debug 9 Core debug was 0 and is now 9 WIRELESS2*CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 T203

I have a T1 link from asterisk 1.2.23 (also tried with 1.4.13) to a Meridian Option 61C. Calls either way drop with error "Channel 0/23, span 1 got hangup, cause 100". Can anyone offer insight into the cause and solution/workaround? (I tried upgrading to Ast 1.4.13, and upgrading matching zaptel & libpri, put the problem is identical). For testing, I tried a call from the

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

Any ideas? Sangoma support is closed for the evening. I have the latest Sangoma drivers and Asterisk 1.4 everything installed. When I fire up asterisk, I keep getting "Primary D-Channel on span 1 up" repeated over and over. The B channels never come up. There are no errors in any of the logs, zttool, or the wanpipe tools. Intense pri debug output: < Unnumbered frame: < SAPI:

I've got a couple of PRIs coming in from a SUMA 4 switch with some 800 numbers routed through it. When the calls come in, I get the following message on the console and the call never makes it through: (800 number is fake) Extension '8005551212' in context 'nonauthenticated' from '232102749585' does not exist. Rejecting the call on span 4, channel 1. I do have the

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Does anyone know how to monitor * to see if they are receiving timing slips on a span connected to a T100P card? I am seeing b-channel restarts quite often and also getting "No D-channels available" warnings from time to time. Yesterday I had all the b-channels crash during a MeetMe Conference. Not good! This PRI is connected to an Avaya Definity PBX that is onsite and located in the

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <meta http-equiv="Content-Type" content="text/html;charset=ISO-8859-1"> <title></title> </head> <body text="#000000" bgcolor="#ffffff"> Hi,<br> <br> have any one sucessfully connected E100P to Cisco? I am

Does Asterisk work with Lucent or any other PBX phone systems????

Hello- I have a system with one D410P and one B200P (both OpenVox). All is well with the D410P, inbound and outbound, and I can initiate calls on the B200P BRI span, but there may be something wrong with my inbound BRI setup: there is no indication of an inbound call when I dial in to it from the PSTN. When I run "pri intense debug" and make a call to the BRI span, I can see a

I have a user who's system crashes on pri hangup request. Tried 1.4.19.1 and 1.4.20 as well as the latest libpri no change Progress is as follows...... < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000 EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 025 P/F: 1 < 0 bytes of data -- ACKing all packets from 24 to (but not including) 25 -- Since

I managed to get Asterisk working with my PBX using T1, now I am moving on to trying to make PRI work. I have my zaptel.conf and zapata.conf configured as follows: Zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone=us defaultzone=us Zapata.conf: [channels] transfer=yes immediate=yes callprogress=yes language=en context=default switchtype=national signalling=pri_net group=1

I've having problems with a BT 2 span ISDN-30/Digium TE205P asterisk setup with outgoing calls not completing and requiring an Asterisk reset to 'unstick' span 1. Sorry this is a bit long but I'm completely out of my depth :-( This system has been in use for some while and I recently upgraded it to asterisk 1.4.24, zaptel 1.4.11 and libpri 1.4.9. I didn't change

Calling all Definity admins, Got a few questions about Definity -> Asterisk interoperability. 1) What are the options for integration? Can I hand off extensions from the Definity and vice versa? 2) Anybody have any working configs they would like to post? I've found and read the legacy integration on the wiki about the two systems. I've also googled and found a few threads that were

I there, I have some trouble to do working caller id name for outgoing calls on the PRI we just installed. Caller id name work on incoming calls only. Caller id number work on incoming and outgoing calls. The provider, Goup Telecom, said that's in what i'm sending. They said that I send the cid name in ascii code and to do it working, I need to send it in hex. So I take some traces

Dear All, I am trying to setup an ISDN line from local telco on a digium card. The problem I am facing is that I am not getting any caller id from the telco. They say that they have enabled caller id. Please help me out. My zapata.conf -------------------------------------------------------------------------------------------------------------------- [trunkgroups] [channels]