similar to: Quick question on source cvs files

Hi I have been searching the wiki and mailing lists and I cant see where my config is incorrect. I have a Digium tdm11b (1 fxo + 1 fxs) this is the output of cat /etc/zaptel.conf # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: WCTDM/0

Hello I've been googling for this message, but can't find why Asterisk sends a warning. The configuration files look similar to http://www.voip-info.org/wiki/index.php?page=Asterisk+config+zapata.conf.sample It's a TDM card with just one FXO module on it, and I connected an RJ11 cable to it from the wall plug: # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv

Hi there, I have a TDM400P (1 x fxs, 1 x fxo) which I'm attempting to run on linux 2.6 (gentoo), without much success at the moment. I have previously had it working on a 2.4 installation, but when I moved to a new box and installed a 2.6-based system, it failed to work. In both cases I'm using whatever (libpri, zaptel, asterisk) is checked out by default (I assume that means HEAD)

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

Hi Friends! I need help! I'm still Asterisk rookie, so please forgive me. My Asterisk is no longer answering incoming call on the phone line. I call the phone and it rings but asterisk is not picking it up. The phone line is attached to port 4 (FXO) on my digium TDM411P card. I am running Asterisk 1.4.11 with zaptel-1.4.5.1 and libpri-1.4.1 on Fedora Core 5, Linux Kernel

I am trying to configure Asterisk for BSNL, india network. I have successfully configured it for outgoing calls. When any outside number make any call to trunk then it receives the call properly but when the call is disconnected by inside extension then outside phone does not get a busy tone. Asterisk incoming call log: -- Executing [s at incoming:2] Dial("Zap/4-1", "Zap/1")

I've just finished updating my Asterisk to the CVS version. Unfortunately, chan_zap won't load anymore. The hardware has not changed and the config files have not changed. I can re-install the two packages back and forth. The old one will still work. The new one won't. I tried updating to a brand-new zaptel and wcfxo modules, with no difference. This has got to be the most

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

I've spent all day today trying to fix an echo problem and I've made no ground whatsoever. I have Digium TDM400 with 3 FXO & 1 FXS. I've tried this computer at two completely different sites with different phone providers. I've tried compiling & installing different versions of Zaptel (currently running 1.4.0, started at 1.2.9 and worked my way up). I've tried

Hello everyone! I installed Asterisk following the instructions of the book "Asterisk: The Future of Telephony". (very nice book) However, I failed. I installed zaptel, libpri and asterisk (in this order). The Installation of Zaptel is successful and my TDM400P is correctly detected: # zttool Alarms Span OK Wildcard S400P

Dear list, I am trying to learn how to use Zap-things in Asterisk. While loading Asterisk verbosely I get this error: [chan_zap.so]Warning, flexibel rate not heavily tested! => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Mar 12 17:19:01 WARNING[5563]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or directory Mar 12

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

Hi everyone (Mark, Jim). I am new to the list but thanks to both Mark and Jim, I have being using "asterisk" since summer 2001. I am just updating my version that was a year old. Yes, I know, I got busy with other things like paying bills so I don't have to sleep with the dog anymore. Anyway, one of the frustrations I have been dealing with (keep in mind that my version of

Hello 1. I don't have deep knowledge of either Linux or Asterisk, but I seem to have successfully installed 1.4 with Zaptel (for support for an OpenVox PCI FXO card) on a stock Ubuntu 7.04 Server Edition: ======== dmesg ========== [ 25.990943] Zapata Telephony Interface Registered on major 196 [ 25.990948] Zaptel Version: 1.4.5.1 [ 25.990950] Zaptel Echo Canceller: MG2 [ 27.523605]

I have installed FC3 using the notes from lesnet http://www.voip-info.org/tiki-index.php?page=Asterisk+Fedora+Core+3 It worked very well, worked first time. My configuration consists of: (1) TDM400P w/ 2 FXS daughterboards and w/1 FXO daughterboard I use yum update to update my installation. After the update and reboot, I attempted to recompile zaptel, Zapata, libpri, asterisk. No errors,

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

Can someone please help me with my config settings for my TDM12B. I have got the FXS port to work fine, but I cannot get asterisk to startup with any settings for the fxo ports. It appears to be something related to the message "Signalling requested is FXS Kewlstart but line is in FXO Kewlstart signalling". However, I have tried what appears to be every possible configuration option. I

zaptel compiles fine (make linux26) but when I modprobe ztdummy I get the follow error. [root@localhost zaptel]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy System info: Linux localhost.localdomain 2.6.9-5.0.5.ELsmp #1 SMP Thu May 19 19:24:44