similar to: TDM Card loses Dialtone and Battery

Excuse my ignorance here, but I am desperately trying to isolate the IRQ for my TE110P card (shown below as t1xxp) Ive gone into my bios and disabled all usb , parallel, serial and some other devices, those that I needed to keep, I have moved off of IRQ 10 and onto IRQ 5, but everytime I boot up, I get usb-uhci and ehci_hcd using IRQ 10 as well as my Digium card. Does anybody know what these are

Hi, Every time I dial into my asterisk box i hear nothing but asterisk jittering. The following is an example of what I get on the asterisk CLI Thanks *CLI> DEBUG[81926]: File chan_sip.c, Line 3826 (check_user): Setting NAT on RTP to 0 DEBUG[81926]: File chan_sip.c, Line 4807 (handle_request): Check for res DEBUG[81926]: File chan_sip.c, Line 952 (find_user): Call from user

Hello, After poking and prodding at Asterisk and Zaptel for over a couple years now, I've dedicated some time to actually reading the code and trying to figure it out. It's been fascinating. With the driver source on one part of the screen and a pdf of "Linux Device Drivers" on another part I've aquainted myself with device driver programming and the interesting

I know, I know, check the archives but I can't find an answer since the new cards are well, NEW! I understand the whole issue of expandability and flexibility of using a T1 card and an Adtran 750. FXO or FXS, you mix and match. With the new card offerings from Digium I can easily put a 4CO by 8 Station system together. Barring the extra interrupts, extra CPU Cycles of extra interfaces, is

Have anyone experienced mixed meetme conferences? Im running a 12 seat call center outbound only. Asterisk 1.2.8, SIP/ulaw at the phones, SIP/ulaw to the SIP terminator. Machine: pentium Dual core 2.0ghz (533 fsb) , 1 GB RAM (533mhz ddr) , 2 SATA 80GB DISK in RAID 0 via software RAID driver. Two Intel PRO 10/100 NIC, IRQs are separated, an X100P so not to use ztdummy. Motherboard is an Intel

Guys.. I just noticed that my grandstream handytone 286 ata are having problems with voice cutoffs... We can listen to the person on the zap channel (x100p cards) without problems but they sometimes listen to us with cutoffs.. like "He ...lo..... ow...r.. you" and it comes and goes.. this doesnt happen all the time but often enough. Any ideas what might be happening or what do I need

Hello All, I am getting a set of errors when I boot Asterisk that I have not been able to solve. What is causing these error(s)? Asterisk boot output: ============== Asterisk CVS-04/10/04-21:44:51, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= [

Heya all, I'm experiencing some problems with a TDM40P and was wondering if anyone else on this list has similar experiences, or maybe even a possible solution. My setup is a dual PIII-750 with 1 gig of RAM, with an X100P, connected to an analog line to my telco, and a TDM40P with analog phones connected. The TDM-card is not sharing any interrupts, but the X100P is, with the 2 Adaptec SCSI

> Subject: Re: [Asterisk-Users] Booting error - Unable to specify channel 2: > No such device I just went through all this as well. The best thing to do IMHO is to try to find a way to manually assign IRQ in the BIOS. Also, and this is what I didn't see at first, some slots SHARE IRQ. Avoid this! If you are not using USB at all, turn it off in BIOS if possible. Tell the BIOS

Hi all i need urgent help our entire switchboard is down only 5 days after it came up. this is the second time this has happened and i am thinking that asterisk is not worth the trouble it gives. mostly it runs without hassle. but around 2 weeks ago during the test phase we rebooted the machine and did the normal modprobes and this error popped up. coming back to work after the weekend the

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

I have read thru what other users have tried in this list when they have experienced seemingly similar issues to what I have, without success. I suspect there might be an issue regarding both the X100P and TDM04b cards being used in an Intel SE7525GP2 motherboard, as I had to even wait for a BIOS update from Intel in order to utilize my 3ware 9500 SATA raid controller on it (3ware Kb -->

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Dear Sirs, I'm running an Asterisk 0.9.1 in a Fedora Core 2 box. I installed a X100P card on my box and when i try to load modules i am rejected. When i type modprobe zaptel my Fedora respond : "FATAL: Module zaptel not found." . The same uccurs when i type "modprobe wcfxo" May you help me. Thank you in advance Juanjo

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hi all, I've struggled for several days trying to get a Digium TDM04B 4-port wxfco card working on a Dell 1U PowerEdge 750 machine running Fedora Core 1. I finally got a call back from Digium who indicated that there is a fundamental conflict between the card and the PowerEdge having to do with PCI interrupts. Asterisk version is stable v1-0 12/29/04. The symptoms of the problem were as

Hi All I've bought a TDM400P and need some help with configuration. Can you tell me what to do ? I've tried to install and the message below has appeared: [root@voip asterisk]# modprobe zaptel [root@voip asterisk]# modprobe wcfxo /lib/modules/2.4.22-1.2115.nptl/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid

I'm debugging a TxFax problem whereby the fax transmission fails. I suspect interrupt latency--some interrupt routine is holding its interrupt too long. I have all unnecessary services switched off and X is not running when I perform these tests. Some transmission are successful while others fail at random points. I've noticed that after I boot Linux, load zaptel, wcfxo, and wcfxs,

Thanks for the reply Bill. I am aware of the interrupts problem. To solve it I have already disabled my serial ports freeing up interrupts 3 and 4 and these are allocated to the two cards. This was done 2 months ago and has not solved the problem. Is there any way that something can wake up every now and then and generate these two interrupts? My current /proc/interrupts is as follows: