similar to: Packet8 Minus the DTA

I found some old messages regarding a possible pkt8 DTA "bypass". Anyone is using Packet8 with Asterisk? ========== http://www.dslreports.com/forum/remark,7292324~root=voip~mode=flat Got Softphone Working with Packet8 Friendly name: {Anything you'd like.} SIP domain: packet8.net SIP proxy: packet8.net Leave everything else at the default. When you login, it will ask for a username

I have packet8 and I have spent many hours on the phone with them. If someone has found away around there DTA configuration I would like to know so I can bring it in house to my * box. But as far as your question is concerned. No. Not that I know of. They wouldn't give me any information about the configs. .o-------------------------------------------------------o. Brian Fertig Network

I'm trying to get asterisk working w/ packet8 (incoming and outgoing) and a dta310 so I can have more control over voicemail. I've looked at the data stream coming from the dta310 and from packet8, but I haven't managed to get the phone to actually place invites through asterisk. On the asterisk end with chan_oss.so, I can make it dial and I hear ringing and the first second of

Hi John, I've been using Packet8 via a physical ATA and XP100 card for some time. As far as I know it is not possible to connect to the Packet8 service without the ATA. If this is not the case I would be very interested to hear this. In addition since moving to the USA I now only have a single packet8 line into my asterisk box (I used to have this and a 2nd regular pstn line) I used to be

I have my DTA310 getting an IP via DHCP. I loaded the unlocked firmware version (Application Code Version: DTA version 1.0 US (8x8 001111)) onto it via TFTP, so I could access the SIP configuration. Under the SIP config, I put the IP of my * system, the 5060 port, and for Domain Name, I put default (is that right?). I checked off the Send Registration Request box. Dial Plan I left at the default,

Noob here, my apologies in advance. Recently my employer decide to stop paying for my home POTS line, so I ordered packet8 for a home line instead of another POTS line, since I really dislike my local phone company, and the POTS line without any long distance would cost more than the $20 to packet8 with unlimited US calling. Anyway, this whole thing got me started thinking about VOIP a lot

Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ... TRUNK=H323/BYEXTENSION@pstn_gw ...

Looks like www.packet8.com <http://www.packet8.com/> has been hacked :-( The phone service is offline as well. Interesting to note that the whois is showing an update today but doesn't look like details have changed. Domain Name: PACKET8.NET Registrar: REGISTER.COM, INC. Whois Server: whois.register.com Referral URL: http://www.register.com Name Server:

I received a message from Packet8 last night telling me they added some new area codes. I took a look at their new area code/rate center finder page and it looks like the added a LOT of new area codes. They now have phone numbers available in almost every state. The URL for finding out which area codes and rate centers are available with Packet8 is at http://www.packet8.net/about/areacodes.asp

I am aware of a least a few people (including me) who were using the Packet8 service along with Asterisk for outgoing calls. Last night Packet8 did a software upgrade and both last night and this morning I have been unable to make any outgoing calls. Has anyone else noticed this behavior and/or been able to correct it? I get Got SIP response 403 "Forbidden" back from 4.42.235.170 when

Has anyone gotten Packet8 setup as a sip trunk for Asterisk? Would they be so kind as to share their config or point me to a website that shows how it can be done? I would be much obliged. Grady -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060621/311435fd/attachment.htm

Thanks in advance. I pass data sets between R and Stata and think dta files would be the best files for this. To do this I can use package foreign or package memisc. I mostly use foreign, although have used memisc and this problem mostly didn't happen, but created errors at other times. I have a csv data set (and created a test case) with with at least one column completely missing. This

**** DRAFT **** DRAFT **** DRAFT **** DRAFT **** I've been using the DTA310 from Packet8.net for a couple of weeks. The DTA310 is about $130 without the Packet8.net VoIP service. It only supports SIP. On the back of the DTA310 is a power connector (power supply is provided with the product), a 10/100 Ethernet port, an FXS port, and a reset button. The front of the device has LEDs for

I'm trying to read in a Stata file but I've never used this function ( read.dta). It's the only one that seems to come close to working, but I keep getting this error: > data<-read.dta("C:/Documents and Settings/Chris/Desktop/S4412/catestscores.dta") Error in read.dta("C:/Documents and Settings/Chris/Desktop/S4412/catestscores.dta", : a binary read

I got a .dta extension file by e-mail, but I can't save it in my computer and open it in R. How can I do it? [[alternative HTML version deleted]]

Hello, I need to write out a data matrix as a STATA 7 file and this happens perfectly with write.dta(), except I cannot seem to export the labelnames to Stata. So far I have tried the following: # X is the data matrix that is to be exported attributes(X)$var.labels <- c("apple", "banana", "cat") write(X, filename = "text.dta", version = 7) When i

Dear R-helpers, if I want to read a .dta-file generated by stata 9.0 with read.dta (foreign), I get the message "not a stata version 5-8 .dta-file". I'm using R-2.6.2 and the latest version of the foreign package. Has someone any hint? With many thanks, Albrecht

Hope everyone id doing great .. Just need some clarification over the limit of write.dta. I have some coauthors that use stata and I need to send them my data in .dta format. the data.frame is 41706x229 and I get the following Error in write.dta(Panel, file = "STATADATA/Panel.dta", version = 7) : a binary write error occured Once I subset the data everything works out fine. my

I'm trying to read in a perfectly good Stata data file created using Stata 10 in Linux and saved in the version 8/9 format using "saveold". R fails to read in the file: aa<-read.dta("myfile.dta") Error in read.dta("myfile.dta"): a binary read error occurred If I resave the file in Stata using the "nolabels" option of saveold, I get: There were

When I import a data file in stata format using read.dta, the full variable labels (e.g. variable= "inc2000"; variable label= "Total household income in year 2000"). When I then export the same data file using write.dta, the variable labels are not included in the new .dta file. Is there any way to ensure that the variable labels are maintained? Thanks [[alternative HTML