similar to: Zhone Zplex Hack & Diddling the Battery

Mine has been working well, but the only problem is that it doesn't support callerid (from the POTS side). > -----Original Message----- > From: John Schmerold [mailto:john@katy.com] > Sent: Tuesday, 5 August 2003 12:37 PM > To: asterisk-users@lists.digium.com > Subject: Re: [Asterisk-Users] Zhone Zplex 10 units > > Thanks for the Zplex heads up. > > Steven

Hi. I was wondering if the zplex in the dev kit could be configured to have all fxs ports, instead of the standard 8 fxo + 16 fxs. If so, anyone managed to do that? Matteo. -- Matteo Brancaleoni Powered by RedHat Linux 8.0 Linux User #153521 -----BEGIN GEEK CODE BLOCK----- Version: 3.12 GS d? s:- a- C+++ UL++++ P+ L+++ E- W+++ N++ o K- w-- O- M-- V-- PS PE- Y PGP++ t 5 X+ R tv- b++ DI D+ G e

Hey guys, I've had a working Asterisk setup going for a while now, but am having problems with the Zhone Zplex 10b thinking that during ringing, an extension has answered the call when infact it hasn't. This only seems to happen on some of the ports and doesn't appear to be specific to the handset. Does anyone have any suggestions as to how I could go about fixing this (aside from

Hi I have the last firmware for zplex, if you like i send it to you, about the second question 24s means 24 extensions so you can configurate as you wish as fxo or fxs. Att Yelson Vivas

This may be a long shot, but I suppose it can't hurt to ask! I have seen chatter regarding Zhone channel banks amongst the asterisk users primarily. In all of my searching I am guessing that the majority of people using the Zhone's are probably reading this, and with the support that I have seen from Zhone so far this is probably my best bet, I recently picked one up for a project

Hi, I have a mint, like-new (used only once) Zhone Z-Plex channel bank for sale. It has 16 FXS and 8 FXO (part number: Z-PLEX-10-24S/O). It functions as a channel bank, router, and CSU/DSU, combining T1, analog voice, and data. D4, SF, and ESF line formats are supported with AMI or B8ZS coding. It has dual T1 jacks, one ethernet jack, one serial port, one V.35 port, and 24 analog pairs

I have been playing with Asterisks for about 6 months, and have fallen in love with it. I have finally taken the plunge and gotten a T100P and a Zhone Zplex-10B (24FXS) channel bank. I have read everything that I can find on the mailing list, checked wiki, even searched the web with google. I believe that most everything is configured right The drivers load without error, and asterisks

The benefits of * are obvious so that part of the marketing an * solution is easy. Anybody care to share ideas on how to target companies who would benefit most from */Digium? It seems to me that it would be an easy sell to small/medium companies who need advanced features such as ip trunking, IVR, Conference bridging, etc., etc. I would like to find a way to identify multi-location companies

I'm hoping that someone else has seen this problem. Running CVS version from 03/08/03 20:00 T100P -> Zplex-10 All internal call routing seems to work fine. Atempts to make calls on the FXO interface fail. Asterisk picks up the correct number dialed but there seems to be a problem with the Zplex transmitting that number on the POTS line. All attempts to dial out fail with the LEC giving

Hi Everybody I'm connecting a zplex 10B to a TE410P card on my asterisk server (i use a cross cable), the zplex doesn't show any alarm neither the server. I'm trying to make calls from 1 line from the channel bank, to another, but when I dial the ext number, the dialtone doesn't stop... every way i make the call and the called extension rings but when i pick up the phone i just

Please point me in the right direction as to where to increase the length of time I am sending DTMF tones on my T100P. I can't remember where/how I set it last time, and I need to do a fresh install. I'd sure appreciate it :) Sincerely, Andy Hester Consero (817)375-1244 (817)937-7977

This probably has an easy solution, but I found it yet. How can I get out of a remote console after using ssh to get into the box, making changes, reload etc. without stopping *? Thanks in advance. Sincerely, Andy Hester Consero

I've got a Wildcard T100P along with a Zhone Zplex 10 24S/O which has been working fine for me now for a while. These have been pulled out of a working Asterisk installation (as they were no longer required) to use at home only to find that the fan noise is too loud. As such I'm looking to sell off this hardware and replace it with some combination of fanless hardware that will allow me to

hello all, I still experience the random off-hook on my fxo cxhannels, i am using a zplex-10b channel bank. which does not allow me to call out. The situation still persists...this is what i have in the zapata.conf [channels] context=internal context=incoming context=default usecallerid=no usecallwaiting=no signalling=fxs_ks channel=1-8 signalling=fxo_ks channel=16-24 but i still have the the

I have just make zhone set2default to factory default setting. What do i have to do to make T1 interface zhone match with T100P.

Is there a way to initiate a transfer using an analog handset? For instance I'm looking for a way to do something like the following: External call comes in and is answered by user A. After talking to the caller they determine that the caller really needs to speak to user B. Is there any way for user A to initiate a transfer to user B, using only their analog handset? Now to make

HI Asterisk Gurus I'm connecting my * server to a zplex 10B, I'm using a slot on my TE410P card as T1 to connect my server to the channel bank (i use a cross cable), the zplex doesn't show any alarm neither the server. I'm trying to make calls from (ext 1) from the channel bank, to other (ext 2) in the same channel bank, but when I dial the ext number, the dialtone doesn't

hello * users, i am using a zplex 10b(8fxosand 16fxs) connected to a T100 digium card, RH8.0. soon after running * i get this warning "file chan_zap.c,line 4155 (ss_thread):CallewrID returned with error on channel 'zap/7-1' then executes the other applications itself. --executing Wait("Zap/7-1","1") in new stack. -- executing..... it gives the same warning

Has anyone been able to get conference calls to work on the Pingtel Phones? I assume this feature works with their implementation, but connected to my asterisk box it doesn't work. The Pingtel phone thinks it is making a second call, but asterisk never sees anything about a second call. Any help would be appreciated. Sincerely, Andy Hester Consero

Hi All, I am considering testing out some analog sets with * for a customer and thought I would ask what analog phones are in use? The customer would require the usual business functionality ie hold, conference calling, and preferably a soft key to vm and line apearances(correct terminology?) in order for secretary to see if their boss is on the phone before transferring a call, etc. I would