Displaying 20 results from an estimated 800 matches similar to: "New to Asterisk need help with caller id"
2003 Dec 09
1
Outbound iax dialing to one #
What I am trying to do is in the 3rd option dial my cell# thru voicepulse I
just can't figure how to construct the line
[inevans]
exten => s,1,setcallerid(${CALLERID})
exten => s,2,Dial(MGCP/aaln/1@Egraph-1,10,tr)
exten => s,3,Dial(iax2/passwod@voicepulse.com/
Where do I put the # to dial 18708573287
thanks
James Schenck
Egraph Design Inc.
Arkansas Online Internet Services
(870)
2003 Dec 12
2
Dlink DG-104SH
Hello,
Anybody has it working with asterisk? Could you share your experience (
good/bad)
Thank you
--
Anton Yurchenko<phila@dg.net.ua>
Digital Generation
2003 Dec 08
0
MGCP caller id problems
I am have trouble getting caller id to work here is my current mgcp.conf am
I missing something?
=========================================================
Mgcp.conf
[general]
port=2427
[Egraph-1]
;dlink 104s-1
host = 12.151.207.2
context = local
line => aaln/1
callerid = "jim's office 1" <321>
line => aaln/2
callerid = "jim's office 2" <322>
2003 Dec 05
3
MGCP IADs
Hi,
For MGCP users. Is there any success stories with any MGCP IAD vendor.
I?m trying to find an IAD which works with Asterisk. I?ve tried the
Cisco IAD 2430 without success; but SIP on this IAD works but it?s
limited (no authentication, no notify messages, etc) and with higher
density IAD (16 or more ports) it?s nice to control using MGCP.
Any information will be apreciated !
Thanks.
--
2003 Dec 10
9
Computing horsepower needed
I have been reading asterisks and everything I can get my hands on for the
past week. I want to know what class processor is the bare minimum I need
for a four port Asterisk installation?
Thanks
2003 Sep 24
3
Dlink DG-104S (chan_mgcp) and configuration w/Asterisk
I have a DG-104S (which I reset to factory settings, it's DHCP'ing off my
network, plugged into the WAN port). The system comes up, and I through the
web browser set under Call Agent IP Address to:
Notify Entry: dlinkgw@[192.168.1.1]:2427 (192.168.1.1 is the * server)
I have RGW Name: and DNS IP addres the DNS IP of the MGCP box and DNS State
disabled (not sure what to set it to) --
2003 Dec 29
1
transfer with MGCP
Hello,
I`m try to make the attended transfer work Dlink DG-104S via FLASH, when
somebody calls my phone I pickup and press flash to get a second line to
call another extension. When I press flash I hear no dialtone, and only
a long and then small beep. When I try to dial digits I hear again those
long+short beeps, but the extension dialed is not ringing. If I pres
flash again I get back to
2003 Jul 30
2
MGCP behind NAT
Hi,
After spending some time trying to get a DG-104S working behind NAT,
I finally found the problem.
I made the incorrect assumption that nat=yes in mgcp.conf works just
like sip.conf. The channels within a gateway are treated more closely to
zap channels than sip channels (from a .conf standpoint).
What this means is that you have to put nat=yes BEFORE any
subchannel definitions:
This
2003 Oct 20
1
mgcp transfer takeback with ata186 (logs with comments - long post)
Hi,
in following of a recent discussion I got to work on MGCP with the Cisco
ATA186 again, and got it to work very nicely. However, there is a little
thing with transfers I would like to get comments on:
Call comes in from PSTN and goes to an ATA186 (MGCP)
Call is answered and then, using flash, transferred to another extension
If the extension is available, there can be an announcement and
2004 Jan 22
3
MGCP w/8x8 DTA-310 and as5300 pstn gateway
Hello folks,
I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no
dialtone & can't get it to ring. My mgcp.conf says:
;
; MGCP Configuration for Asterisk
;
[general]
port = 2427
bindaddr = 0.0.0.0
[172.16.2.25]
host = 172.16.2.25
context = default
line => aaln/1
And here's the interesting bits of extensions.conf:
[globals]
...
TRUNK=H323/BYEXTENSION@pstn_gw
...
2005 May 20
2
MGCP 1.0 / NCS 1.0
I'm trying to use a 4 port ATA that was designed for use with MGCP 1.0 / NCS
1.0 -- is the channel_mgcp compat with NCS -- anything I can do to make it
compat?? This is what happens - below
*CLI> mgcp reload
Reloading MGCP
== Parsing '/etc/asterisk/mgcp.conf': Found
Use EXIT or QUIT to exit the asterisk console
== MGCP Listening on 10.1.22.39:2427
== Using TOS bits 0
mgcp
2004 Oct 15
1
Asterisk crashes on special Transfer with MGCP/ATA 186
Hi all,
i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco
ATA-186 3.1.1 atamgcp
We are used to make an special ;) blind transfer like
(Flash)Number(Hangup before anyone answers or ring).
Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp
If one waits until the last one rings, then hangup, everything is fine.
If one waits until the last one
2009 Dec 17
2
Integrate a CPE with Asterisk in MGCP
Hello all,
I'm looking for some help to try to understand why my CPE doesn't work
good with Asterisk in MGCP.
Here is what I want to do :
- Register a TECOM AH4021 on Asterisk in MGCP with the following profile
in mgcp.Conf :
[general]
port = 2727
bindaddr = 10.95.20.1
disallow=all
allow=g729
allow=alaw
020202020202]
context=mgcp
host=dynamic
canreinvite=no
dtmfmode=rfc2833
nat=yes
2003 May 19
1
MGCP and Cisco ubr924
I've been trying to figure this one out for a while, but to no avail.
I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2.
Any help is appreciated.
from mgcp.conf:
[ubr924]
host=65.37.86.203
context = from-sip (just as a
2004 Dec 22
1
MGCP Transaction identifiers
I know this is not the most appropriated list to this, but I will try:
Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method?
I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,
2004 Aug 18
2
Festival Installation - Asterisk 1.0-RC2 && Debian Woody
Hey All,
Thought I'd take a bash at trying to get Festival to work here on my lab
system with the aim of using it to create our IVR menu prompts. I've
spent most of the afternoon searching through the Wiki, the Festival
website and Google and I've got a couple of questions.
First one is that the 'Asterisk+festival+installation' page on the Wiki
mentions the RedHat 9 RPMs
2003 Apr 24
3
new mgcp patch errors
see below
I tried to call 98013356 from the following phone (from mgcp.conf)
[iptlf03]
host = 192.168.33.3
context = default
inbanddtmf = 1
callerid = 22545062
line => aaln/1
Console output:
== Spawn extension (capiring, 9988001133335566, 1) exited non-zero on
'MGCP/aaln/1@iptlf03-1'
-- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03
-- Delete connection 4
2004 Jan 22
2
MGCP Problem.
Hi.
I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk
with the next configuration files.
'--------------- extensions.conf
----------------------------------------------------
[general]
static=yes
writeprotect=yes
[globals]
ap1 => mgcp/aaln/ap200@64.76.148.186
[macro-apl1]
exten => s,1,Dial(${ARG1},30,Ttmr)
;exten => s,2,Voicemail(u${MACRO_EXTEN})
2005 Mar 25
2
MGCP issue
Hello List,
I'm trying to setup MGCP channel with a Centile Media Hub box. My
Centile box has 4 ports and I got no dial tone. Can somebody help with
this isuue?
This is my mgcp.conf and extensions.conf
Thanks
Daniel.
; MGCP Configuration for Asterisk
;
[general]
port = 2427
bindaddr = 192.168.11.20
disallow=all
allow=g729
allow=alaw
allow=ulaw
[192.168.11.200]
context=MGCP
2005 Aug 17
1
Comfort Noise incomplete - No translator path exists for channel type MGCP (native 4) to 256
I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below
I go off hook