similar to: Adtran 750

I believe it is not fiber, but I am not sure. I am going to take one of them home tonight and hook it to my POTS line there, which for sure is not fiber. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Michael Welter Sent:

All, I need help. I have an (actually 2) Adtran TA750's with 8 FXO ports. I get a terrible buzz on every FXO port. If I unplug the Adtran and put an analog phone on each incoming line, I have no buzz. I also have 2 Carrier Access Access Bank I's with 12 FXO ports. When I plug the same analog lines into either one of those, no noise or buzz whatsoever. I went so far as to move the TA750

Rich Hi, After Qwest pronounced my circuits as within spec. (yes, disconnected from the house) I listened on the lines with my butt set. Clear of all noise and hum. I then got my box of Cat3 and laid a circuit around the outside of the house and into my lab. Still clear of all noise and hum. I then connected the circuit to the Adtran and made a call. Lots of hum and buzzz. As I said,

Rich, Thanks a bunch, totally understand now and that actually makes total sense. (no need for schematics). This also explains why I used an TA750 to go into a Nortel MICS system, using FXO and no buzz. Totally balanced load from the analog ports on the Nortel across the 5 feet of CAT5 to the FXO on the adtran. Now I need to get rid of some Adtrans --- Anyone lookin to buy? :) Thanks

Hello, I new to this, but with the help of mailing lists archives and IRC I am able to build my PBX. Thanks to all who had help me to reach till here. I am stuck at a point where I can't find the solution on mailing lists or even on IRC. I have individual 4 DID (Direct Inward Line) coming from Telco and terminating into TA 750 to FXS card. Many of them told that Phone instrument terminates

Just when I thought I couldn't be wrong, I was wrong. We have woodpeckers that drill into the arial telephone cables, and water seeps through the holes and partially grounds the tip and/or ring wires causing hum. I thought the hum/buz on my lines was a telco problem. The Qwest HQ noise team assures me that my lines are within spec. Sure enough, when I listen on the test set the lines

Hi List, I have some T1 750s; hookup via a T1 to a TE420P card. We have them all set as E&M wink trunks. We get a dial tone and can call numbers, but when i call another number the ringing I hear on my phone is very weird, its not the standard ring tone. What will cause this? Is this a * setting or something in the Adtran I am fixing, I just want good ole ringing to be heard! Any help would

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

Hello Can somebody send me please config files of zaptel.conf and zapata.conf for adtran fxs ports. I cannot make it work. I do not get a dial tone on Adtran and when I am trying to call from sip i get: app_dial.c:674 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy at this time There are no errors on T100P and adtran. Please help! B.

I've been trying to get a Win 2000 RAS server working with my asterisk PBX for quite some time, to no avail. I've googled, I've tried loads of configurations, I've rewired phone lines, and still I am not winning the battle. Here's my config. PRI->T400P->Asterisk->T400P->Adtran 750(L36 Firmware)->RAS Server. I have 4 Zap channels signalled FXO_KS to the 750

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

I am sending a call down a E&M wink trunk to a adtran tsu600 channelbank. The extension is setup like so... exten=>799179,1,Dial(zap/g2,20,D(9179)) exten=>799179,2,Hangup() It should Dial the Adtran and send some DTMF signals to a telephone on an fxs module in the Adtran. Asterisk is seeing the call answered when the T-1 is picked up by the Adtran not when the ringing phone is answered.

I have a TDM400P (configured with 4 FXO cards) in a box that was working fine from POTS lines extracted from a Lightspan via DSC's channel bank, but when I switched over to using an Adtran 616 (weird little box, takes an SHDSL circuit in that splits out 16 analog lines via an amp connector) the card no longer seems to be able to detect ringing. I've tried upping the rxgain with no

I've downloaded diax-0.9.6b and configured for IAX2. Calls from Diax to * are perfect. However, when calling from * to Diax, I get the following: channel.c:1097 ast_read: Dropping incompatible voice frame on IAX2[mike]/3 of format GSM since our native format has changed to ULAW In iax.conf I have: allow=all disallow=g723.1 disallow=lpc10 allow gsm Has anyone else seen this? Thanks,

Good Day list, I have googled and wiki'd myself to no avail. Here is my setup. Asterisk Box Digium T1 card connected to an adtran Total Access 624. I need to pass ANI and DNIS information from asterisk to the analog devices hanging off the adtran. The digits are announced to the fxs devices between ring 1 and ring 2 (If I pick up the anlog phone after ring 1, I can hear them so I

Can I configure an Adtran channel bank with a mixture of FXS and FXO cards and have them come into a single T100P T1 card? It seems like this would be a cheaper solution than trying to load a bunch of PCI cards into a PC. Also, when shopping for an Adtran (on ebay) - what do I need to watch out for as far as interfaces or capabilities to make sure that it works with a Digium card?

People on the list tend to think you can't make many cards work on a regular desktop. If you're willing to wait a couple of week I might have an answer for you. _____ From: Robert Augustyn [mailto:augustynr@yahoo.com] Sent: Saturday, December 11, 2004 7:13 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Will Adtran TSU 600 work with *?