similar to: Cisco DTMF Issue

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

Calling from a Cisco FXO port to an ATA-186 (SIP 3.1 image) via * (either CVS-HEAD-06/28/04-11:43:41 or CVS-HEAD-07/12/04-15:49:58) I didn't hear any ringing sound & get the following on the console: -- Called 5503 -- SIP/5503-f6b5 is ringing WARNING[-1323201616]: channel.c:1375 ast_indicate: Unable to handle indication 3 for 'SIP/10.10.2.250-9903' -- SIP/5503-f6b5 answered

Hi. If I use a Cisco as a PSTN termination GW and need to route all incoming isdn calls to my asterisk and all outgoing calls from asterisk via the cisco out to pstn, how do I do that ? in the cisco I have this: dial-peer voice 1 pots destination-pattern [0-9]T no digit-strip direct-inward-dial port 3/0:D ! dial-peer voice 50 voip destination-pattern [0-9] voice-class codec 1 session

I'm stuck running a old copy of asterisk because something strange is going on in later versions of the CVS.. When I call in from a PSTN into my cisco 2610XM gateway which then routes the call to my asterisk box via sip.. Asterisk can no longer process DTMF tones generated by the calling party. This affects DISA, prompts and menus.. Has anyone else had this problem?? and use.. I DO have

I have the following configuration and am obviously missing something small that is causing * not to work as expected. I have the following defined in sip.conf [ccme-in] type=peer host=10.0.9.1 context=devel_in disallow=all allow=alaw nat=no canreinvite=yes qualify=yes and [devel_in] is defined in extentions.conf However when I try to call via the dial peer I have configured on the cisco

I wouldn't expect you to be using RFC3389 if your using A-law, can you include your IOS version and IOS config file ... I have not specified any allow's or disallow's in my * config for the codecs with my 5300, I also use Cisco 79xx phones and I use the option within the phones config file to select the preffered codec and when I change this to G.729/A-law/U-law all works perfectly

Hi, I'm trying to get a remote Cisco Call Manager Express (CME) system behind a dynamic IP address routing both inbound and outbound calls via SIP to my local asterisk server. I've got a local CME system working fine on the LAN, where the CME is at a static IP (host=10.5.7.130 in sip.conf), but I can't figure out how to get it working with host=dynamic, even locally on a test

Hello, We have a sip trunk end point with cisco media gateway. VoIP works fine. But when we try to send faxes thru this trunk, we simply can not. Is there anybody experienced such problem and solved? How should i set sip.conf and udptl.conf. I already have t38pt_udptl=yes in sip.conf Thank you.

I would think I could do this but for some reason I am stymied. I have a PRI from RCN connected to a cisco 3640 (in my day "cisco" is all lower case :-)). My config looks something like this on the cisco... --------------------------------------------------------- voice-card 3 dsp services dspfarm ! ip cef ! isdn switch-type primary-5ess ! controller T1 3/0 framing esf linecode

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

Hello, We have been working with the ReceiveFax application for some weeks now in order to receive faxes in T.38 and it works fairly well, but there are some faxes that for some reason we are not able to receive correctly. The asterisk version we are using is 1.6.0.6 with spandsp-0.0.5pre4 and the asterisk machine is behind a CISCO mediaGW to be able to communicate with the PSTN. The SIP call

I see a lot of comments but no actual show runs. Can someone post a 7206 config. I am having a dickens of a time getting calls to pass. I currently have the following loaded. Cisco IOS Software, 7200 Software (C7200-IK9O3S-M), Version 12.3(8)T6, RELEASE SOFTWARE (fc2) Thanks !!! Jerry -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.344 /

If you have a PRI terminated in a Cisco router talking SIP to * and would be willing to share your Cisco config, please respond. Also, I would be interested in knowing what version of IOS you are using. We are using an NM-HDV in a 3640. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

Ok here is a question that has gotten me stumped. I have an Asterisk system up and running. I need to connect it via the Internet to a Sip Cisco system. This is what they have. I have there IP address's and login. X-lite is able to connect to them and make a call! So I have the name right! CISCO router model: 2621 VoIP module: NM-HDA-4FXS I have done Google lookup and at the Wiki about

List users, It's been a while since I've posted here, but I've been hard at work pushing toward our large scale Asterisk goal and keeping up with this list can be a full time job by itself (I have19,543 unread list messages!!). This Friday, September 16th 2005, my team will be at the MCI Development Lab in Richardson, Texas testing our setup. We have a three server system

I have gotten this sort of problem some weeks ago and have solved it with the mailing list archive. But now I have this problem again with the class library. What should I put in library/class/R/zzz.R? Everything I put in that file leads to the same error message. I'm running 0.61.3 on Linux. > knn1(train, test, cl) Error in .C("VR_knn1", as.integer(ntr), as.integer(nte),

Hello all, When I generate an out-going call from *, the DTMF detection is not working ? ASTERISK --> GW AS5300 --> PSTN But the DTMF is working correctly when it's an incoming call. PSTN - -> GW AS5300 - -> ASTERISK Well, I tried with the 3 dtmfmode of asterisk inband, rfc2833 and info, no way !!! Is it normal that asterisk try to setup the outgoing-call using ULAW ? if I

Hello, I'm trying to receive faxes with asterisk. My configuration is like this: PSTN fax -> ISDN -> Cisco router with VoIP module -> Asterisk When I try to send a fax from PSTN fax I got the standard fax signal, Asterisk starts rxfax application and then call ends and there is no tif anywhere. On the fax display there is still one message: Calling... Part of my extensions.conf:

I've been using R for the last few weeks, but not with much success. If I try sourcing test.R from the 'class' package, I get this error: Error in .C("VR_knn1", as.integer(ntr), as.integer(nte), as.integer(p), : C/Fortran function not in load table I checked the class.so file, and sure enough VR_knn1 is there. Why can't R find it? By the way, I'm running RedHat Linux,

I've been using R for the last few weeks, but not with much success. If I try sourcing test.R from the 'class' package, I get this error: Error in .C("VR_knn1", as.integer(ntr), as.integer(nte), as.integer(p), : C/Fortran function not in load table I checked the class.so file, and sure enough VR_knn1 is there. Why can't R find it? By the way, I'm running RedHat Linux,