similar to: X100P random hangups.

Hi, I'm having random hangup problems with zap channels. If I turn busydetect off in Zapata.conf, * fails completely to detect a user hangup in the middle of a script. On the other hand, if I turn it on, everything works much better, but long calls tend to be hung up without a motive. Any other parameter that I can try? Any #define that I can tweak and recompile? Will callprogress

FYI to anyone else who may be experiencing random hangups; I removed the busydetect=yes lines from the conf files on my asterisk servers, and haven't had a hangup since. I had done that once before and it didn't seem to have much of an effect, so I'm not breaking out the champagne yet. But so far over dozens of calls both made and received since I took that line out, I

Guys, this is weird.. Today I started having some problems with calls been dropped. Im suing X100p cards (clones) and I have this setting on my zatala fle: [channels] language=sp signalling=fxs_ks usecallerid=yes cidsignalling=bell cidstart=ring hidecallerid=no callwaiting=yes usecallingpres=yes ;sendcalleridafter=1 callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes

Hello, my config : aah 2.6 (asterisk 1.2.4) , centos 4.2, 1 TDM11B (1 Fxo / 1 fxs ), 1 phone, 1 softphone I'm in France When someone from PSTN calls and hangs up before the call is answered, internal extension keeps ringing until timeout occurs. PSTN line keeps busy. Hangup detection doesn't work. I've played with different paremeters (callprogress, busydetect, busycount,

I have a customer running Asterisk 1.2.13 with Zaptel 1.2.11 that is having calls dropped. Sometimes you can stay on the phone for a long time and sometimes the call is dropped within a minute. There are 9 lines connected to 3 TDM04B cards. The Panasonic Pbx we replaced did not have this problem. There are 8 SIP phones and 16 analog phones connected to two Astribank-8 units and everyone

Hello, We have a call redirection system setup inhouse to send calls from an incoming line on a T1 to an external dialed out number: Zap(call comes in) -> Asterisk -> Zap(call dials out) The call comes in on a Robbed-bit T1 (d4/ami EM Wink) and goes out on a PRI. We are using Asterisk release 1.0.5 Randomly the calls will drop less than a minute into the call. The Debug messages at the

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

Hi, can't get X100P (fully zapata compatible clone) to work (I'm in Australia). * recognises the card and the channel (1) but has definetely some problems talking to the pots line. I set up this simple dialplan for ZAP ("incoming" context, as setup in zapata.conf, for channel 1) [incoming] exten => s,1,Answer exten => s,2,Playback(somefile) exten =>

Hi List, I've got * randomly hanging up on inbound or outbound calls on zap channels. I use a Digitnetworks X100P clone card. Any idea of what might be happening? Cheers, Jean-Michel.

Hello, After much searching of voip-info.org and google, I'm finally giving in and asking the list. The setup I have is this:- Single X100P card in a Debian system Inbound/Outbound POTS line connects to the X100P Sipura 2000 and Budgetone 100 on the LAN 1 Cordless and one conventional phone connected to the sipura Account on Stanaphone.com for eitherbound SIP calls. (I have other SIP

Hi, I'm trying to get up and running a TDM400 with a standard italian pots line but i'm having problems at getting asterisk to detect when the line get answered on outgoing calls. I'm using asterisk 1.6 beta 9 with zaptel 1.4.11. I tried with and without answeronpolarityswitch=yes but it didn't change anything at all. With callprogress=yes answer get never detected. With

I've been trying to get a Win 2000 RAS server working with my asterisk PBX for quite some time, to no avail. I've googled, I've tried loads of configurations, I've rewired phone lines, and still I am not winning the battle. Here's my config. PRI->T400P->Asterisk->T400P->Adtran 750(L36 Firmware)->RAS Server. I have 4 Zap channels signalled FXO_KS to the 750

Hi, Just wondering if anyone else in Australia is using the X100P to connect to the PSTN, and what configs they have for it? I'm finding at present when I make a call I get a fair bit of echo of myself speaking, and also the person on the other end can't hear me very well (perhaps need to up the digial Tx Gain? I don't have it configured at present) Asterisk is running on

So I made the mistake of buying a Carrier Access channel bank without noticing the page on the wiki about the fact that they don't support disconnect supervision (bastards!). However, apart from that, I do have it working fine for incoming calls. Is there some trick to get asterisk to detect the hangup tones from SBC? I've tried busydetect and callprogress as suggested, but neither

Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not

I'm attempting to use callprogress in my system, and I'm having trouble. Callprogress always can tell if the line is busy or ringing, but when the line is answered, the call does not get bridged. Messages showing that "line is ringing" stop in the console and if the called party hangs up, asterisk reports the line is busy. Are there any settings that I could use to help with

Hi ! I have some issues, i don't know exactly if it's a busy detection issue. When i dial into the Asterisk box, and if i hang up before the Asterisk answers with the IVR Welcome message, the Asterisk goes on with the call. But, if i wait for the Asterisk to answer, and if i hang up, the Asterisk hangs up too. I have this parameters on zapata.conf: busydetect=no

Hi, Does some one experience the Sangoma A20X-ec series card that cant detect the hangup tone? I got * server 1.2.5 and running on Centos 4.3, I hock up to two PSTN lines and each time some one call in and my phone delay 1-2 sec (this is Asterisk delay nothing to do with Sangoma) and it rings on my phone, however, end on the day I got not less that 10 empty messages. I found out that Sangoma FXO

I have a very strange problem I'm hoping someone has encountered already. I've scoured the internet for an answer to this one. My phone company provides no disconnect supervision. Hence I'm forced to use the busydetect feature. I have a TDM400 with two FXO ports. If I call from an internal extension to a landline and then hangup the landline Asterisk detects the busy signal

Details: Asterisk 1.0.9 Zaptel 1.0 Dell P3 1ghz with X100P Clone Location: India This is an interesting issue where when I open up ZTMonitor, it shows the RX as being on. It seems that Zaptel doesn't know to hang up the line so after a couple of hours when the telecom cuts the line, everythign stops working. Things I've tried include playing with the zaptel.conf, trying zaptel v1.2(with