similar to: Missed calls/activity log in Asterisk

Hi, I am having a problem with (Asterisk is crashing) with a Fritz card PCI / chan_capi. Receiving Calls from PSTN works, but outbound calls make asterisk crash (Speicherzugriffsfehler/Segmentation fault). The crash occurs upon dialing with the other phone not even ringing. I hereby ask if somebody reading this list can confirm or disprove my issue. Does anbody run a recent asterisk 2.6 with

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

G'day all, I've been googling myself silly looking for help on this one but have come up blank. I have an AVM Fritz!Card PCI, and I'm using chan_capi v 0.3.1 with * from CVS-HEAD-05/08/04-22:48:00. I can start * and make and receive calls on ISDN fine but after a few hours of * uptime, on any ISDN call I make or receive from my SIP handsets (7960 or ATA-186) I get bad audio: on the

I'm now up&running with - mISDN with avmfritz driver for Fritz PCI card - chan_capi from debian recompiled with a patch (see below) - EuroISDN with Point-to-Point (ptp) mode (Austria) - With Asterisk 1.0.7-BRIstuffed-0.2.0-RC7k from debian sarge But am having some problems: 1) I needed to patch chan_capi.c from debian sarge (see below) to give the new channel to asterisk in state

asterisk-users-request@lists.digium.com is believed to have said: > >Hey Dan!! > >Give us a clue as to what hardware/setup & network provider you have there, >and we might be able to help :) > >Paul > Hello Paul, hello everybody! I have, too, an inbound call problem. I am using an ISDN Fritz Card PCI 2.00, together with chan_capi 3.5.x . As I call my number I get

I'm testing * (CVS-09/16/03-02:07:49 with zaprtc 0.0.1) with Fritz!PCI (chan_capi 0.3.0), and have a couple of funny things - I wonder if anyone else has seen them: - Now and then, * just exits. Until now I had lowish-level verbosity on, so all I saw was 'Executing last minute cleanups'. What can trigger * exits? (in other words, what should I pay attention to when attempting to

Hello List, because this is my first post to this list, i'd like to introduce myself. My name is Thorsten M?ller, 26 years old and live near Frankfurt/Main in germany. Okay, now to the reason for this posting: I just installed my first asterisk server (Debian 2.2 Kernel 2.4.18-686) with AVM ISDN Fritz PCI card (passive). I followed the configuration on http://voip-info.org and the

Since upgrading from stable to latest cvs I can't place CAPI calls (AVM Fritz/chan_capi-0.3.1) Did I miss something that has to be changed in configfiles? Also tried to recompile chan_capi which run into an error. capi info shows me: Contr1: 2 B channels total, 2 B channels free. Any suggestions to these logfile snippets jo ---------------------------- * to ISDN -- Accepting

Hello! I'm curently using * with two old Teles PCI card (wich, btw, were hard to install and make good use of) with ISDN4Linux. The sound quality is simply perfect. However both dialing in and out through the ISDN line, there seems to be a _little_ bit of echo that eventually gets on your nerves ! Also the echo seems to get a _little_ bigger after a minute or so into the conversation. Now,

Hi everyone, Hi, I am new to the ISDN world, today I received my new NT box from CS Telecom but unfortunately it doesn't work. I have installed all the drivers and when I issue a "capiinfo" I get: -------------------------------------------- Number of Controllers: 1 Controller 1: Manufacturer: AVM GmbH CAPI Version: 2.0 Manufacturer Version: 3.101-02(49.18) Serial Number:

Hi, i was able to solve my problem. During my playing around with * and capi i changed several options in config files. I did this while my * was running. To test if my changes where successful i entered "reload" on * console. This didn't help. But after i stopped asterisk and startet it again, everything worked perfect. So it seems that doing a reload while asterisk is running

Hi everybody, is it possible to get asterisk recognising fax calls (NO dedicated msn / extention) with chan_capi or chan_modem and i4l ? But i only have a fritz dsl v2.0 (same features as a fritz pci v2.0, I think). Any hints would be welcome! Only found info about chan_zap. I also have a hfc-s card with junghann's bristuff working in NT mode - maybe this can help? so this is my setup:

I have 10 msns on my isdn bri incoming (AVM Fritz, chan_capi 3.5) When i set in capi.conf [interfaces] msn=1,2,3,4,5,6,7,8,9,10 incomingmsn=* controller=1 softdtmf=1 accountcode= context=tcom-in echocancel=yes devices=2 Only msn 1,2,3 are working. What can i do? Thanks Jens

Bruno Hertz is believed to have said: >Hi Aldo > >don't know about Suse, but I have a working setup with asterisk 1-0 >stable, chan_capi 0.3.5 and fcpci-suse9.1-3.11-02 on Debian Sarge, >though not prepackaged but all self compiled. > >Looking at your log messages, chan_capi obviously is installed, but the >load of app_capiCD.so fails due to an undefined symbol

Hi, I'm heaving trouble using two Fritz ISDN cards in one machine. I followed "http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO" and i think everything works great. cat /proc/capi/controller shows: 1 fcpci running fritz-pci A1 3.11-02 0xb400 5 2 f2pci running fritz2-pci A1 3.11-02 0xa400 10 The asterisk CLI shows: *CLI> capi info Contr1: 2 B channels

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

Hello, i have asterisk with chan_capi ( AVM Fritz card ) working, isdn line BRI, setup to point-to-multipoint. working fine, but when both channel on interfaces are used and somebody wants to call in - the response is "ha-la-li" - sounds like msn or called number does not exists. i think that right response should be - line busy tone... right ? can anybody tell me what is wrong ?

Hi Jon, perfect instructions, thank you very much. I used them and after some tests they worked. Here is what I did. Maybe someone could use it completely: ------------------------------------------------------------ Install helpers: apt-get install kernel-package ncurses-dev fakeroot wget bzip2 Go to usr directory: cd /usr/src wget

Hi all, I've finally taken the plunge and had isdn installed. It's a BRI from Telewest in the UK. I'm told by the provider that it's in point to multipoint mode with 6 digit presentation. I'm using an AVM fritz (bt speedway) with the fcpci-suse9.1-3.11-02 driver. Chan_capi seems to be installed fine. I can receive incoming calls. However, I can't call out. When ever i