similar to: asterisk and zplex10b (fwd)

hello * users, i am using a zplex 10b(8fxosand 16fxs) connected to a T100 digium card, RH8.0. soon after running * i get this warning "file chan_zap.c,line 4155 (ss_thread):CallewrID returned with error on channel 'zap/7-1' then executes the other applications itself. --executing Wait("Zap/7-1","1") in new stack. -- executing..... it gives the same warning

can somebody that has these hardwares(X101P and S400P) working on his asterisk system please assist.................. you can send the solution to austino@skannet.com..... the error message is what i have below. ---------- Forwarded message ---------- Date: Thu, 1 May 2003 21:01:21 +0100 (WAT) From: austino@skannet.com To: asterisk-user@lists.digium.com Subject: Error working with X101P and

Could someone please assist me soonest. when i run asterisk with one X101P card and a S400P card asterisk will run but the card will not work.this is the message i get: [format_jpeg.so] => (JPEG (Joint Picture Experts Group) Image Format) == Registered format 'jpg' (JPEG (Joint Picture Experts Group)) [cdr_csv.so] => (Comma Separated Values CDR Backend) [cdr_mysql.so] =>

I am always getting multiple PCI Master Abort messages when I try to plug in a second TDM400P. I have asked this question before, but I nothing really solved my problem and I just put it on the back burner for a while. I am at a point where this is a crucial issue. I have read that the Zaptel devices share an IRQ, is this causing the problem? Is there a way that I can manually change the IRQs of

hello, I have been using asterisk now for about 2 years now on a RH8.0 it is our main call gateway. I have on the box 3 T1 TDM cards connected to 2 Rhino channel banks (FXS) and 1 CAC Access bank I (FXO) with so many softphones and ATA 186s. It has been working good till today some few hours ago. i just discovered that there were no dialtone on the phones. Asterisk did not spit out any error, it

Mine has been working well, but the only problem is that it doesn't support callerid (from the POTS side). > -----Original Message----- > From: John Schmerold [mailto:john@katy.com] > Sent: Tuesday, 5 August 2003 12:37 PM > To: asterisk-users@lists.digium.com > Subject: Re: [Asterisk-Users] Zhone Zplex 10 units > > Thanks for the Zplex heads up. > > Steven

Hi. I was wondering if the zplex in the dev kit could be configured to have all fxs ports, instead of the standard 8 fxo + 16 fxs. If so, anyone managed to do that? Matteo. -- Matteo Brancaleoni Powered by RedHat Linux 8.0 Linux User #153521 -----BEGIN GEEK CODE BLOCK----- Version: 3.12 GS d? s:- a- C+++ UL++++ P+ L+++ E- W+++ N++ o K- w-- O- M-- V-- PS PE- Y PGP++ t 5 X+ R tv- b++ DI D+ G e

Hey guys, I've had a working Asterisk setup going for a while now, but am having problems with the Zhone Zplex 10b thinking that during ringing, an extension has answered the call when infact it hasn't. This only seems to happen on some of the ports and doesn't appear to be specific to the handset. Does anyone have any suggestions as to how I could go about fixing this (aside from

I've got a Wildcard T100P along with a Zhone Zplex 10 24S/O which has been working fine for me now for a while. These have been pulled out of a working Asterisk installation (as they were no longer required) to use at home only to find that the fan noise is too loud. As such I'm looking to sell off this hardware and replace it with some combination of fanless hardware that will allow me to

I have just make zhone set2default to factory default setting. What do i have to do to make T1 interface zhone match with T100P.

Hi I have the last firmware for zplex, if you like i send it to you, about the second question 24s means 24 extensions so you can configurate as you wish as fxo or fxs. Att Yelson Vivas

I came across this hack while looking through chan_zap.c. Is this still applicable for those w/ zplex cb's? Is it a maybe need or an absolutely need? Any background info would be appreciated. Sincerely, Andy Hester Consero (817)375-1244 (817)937-7977

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial

This may be a long shot, but I suppose it can't hurt to ask! I have seen chatter regarding Zhone channel banks amongst the asterisk users primarily. In all of my searching I am guessing that the majority of people using the Zhone's are probably reading this, and with the support that I have seen from Zhone so far this is probably my best bet, I recently picked one up for a project

Is there a way to initiate a transfer using an analog handset? For instance I'm looking for a way to do something like the following: External call comes in and is answered by user A. After talking to the caller they determine that the caller really needs to speak to user B. Is there any way for user A to initiate a transfer to user B, using only their analog handset? Now to make

Hi, I have a mint, like-new (used only once) Zhone Z-Plex channel bank for sale. It has 16 FXS and 8 FXO (part number: Z-PLEX-10-24S/O). It functions as a channel bank, router, and CSU/DSU, combining T1, analog voice, and data. D4, SF, and ESF line formats are supported with AMI or B8ZS coding. It has dual T1 jacks, one ethernet jack, one serial port, one V.35 port, and 24 analog pairs

I have been playing with Asterisks for about 6 months, and have fallen in love with it. I have finally taken the plunge and gotten a T100P and a Zhone Zplex-10B (24FXS) channel bank. I have read everything that I can find on the mailing list, checked wiki, even searched the web with google. I believe that most everything is configured right The drivers load without error, and asterisks

Greetings, I have just purchased several Astra 390 phones ready for asterisk. I have placed a line with adsi=yes in the Zapata.conf file just before channel => 13 I have also added an extension exten => 6199,1,ADSIProg(asterisk.adsi) exten => 6199,2,Hangup in the extensions.conf file. When I try to program the phone I get the following: Asterisk CVS-03/28/04-12:02:10,

HI Asterisk Gurus I'm connecting my * server to a zplex 10B, I'm using a slot on my TE410P card as T1 to connect my server to the channel bank (i use a cross cable), the zplex doesn't show any alarm neither the server. I'm trying to make calls from (ext 1) from the channel bank, to other (ext 2) in the same channel bank, but when I dial the ext number, the dialtone doesn't

I have a linux (redhat 8.0) samba server that is a part of a Windows ADS. I have gotten user authentication to work fine (I THINK), but still I have some problems with access to share. The strange thing is that I can access the share from smbclient (on the linux server: #smbclient -d4 //Bones/share -U foo where user foo has no user on the linux box itself, so the authentication is done