similar to: 2 IAX2 calls, bad audio

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

Hello, I have just installed an Asterisk server with a Digium TDM410P card with 3 FXO modules (no module in the 4th slot). It's lived on two different machines (a test machine, which had Linux kernel 2.6.28, and a new dedicated machine which has Linux kernel 2.6.32). On the test machine (2.6.28), I used the Zaptel drivers. Once the kernel modules were loaded, the lights on the TDM410P came

Hello friends I've problem with my Centos 4.3. On start some information: 1. serwer HP DL 380 x Intel(R) Xeon(TM) CPU 3.40GHz 2. RAM 4GB 3. HDD storage FC 4. kernel 2.6.9-34.0.2.ELsmp #1 SMP This serwer is working with another one (that some configuration) in RHEL cluster (locking by DLM), as a file serwer with samba-3.0.22. Samba have about 100 simultaneus sessions. Problem is with load

Something new to me. Recently installed a 1.4.30 box for a small office with four POTS lines in a hunt (Digium TDM410P). Had the telco put a "call forward" option on the main line of the hunt. They dial a feature code from their desk phones (Polycom IP450) that results in forwarding the main number to our VoIP service. This is all to let them "try out" our dialtone

Quick and dirty question: for the TDM410P I must use the wctdm24xxp driver? Att Vin?cius Fontes Desenvolvimento Canall Tecnologia em Comunica??es Ltda.

Hi, We're evaluating asterisk, somebody has measured maximum asterisk load (simultaneus calls, calls per seconds...)? Are there any stimation? Thx. Best regards. .G

Hello my friends... We are having some problems with the fax in our asterisk server... We have: Asterisk 1.4.21.2 Zaptel Version: 1.4.11 libpri version: 1.4.5 Digium Card TDM 410P This digium card has 3 FXO ports and 1 FXS port where we have a fax machine connected! The problem is that we can receive fax very good, but we can't make any outbound fax call, in fact, our asterisk get freezed

Actually I can start and receive SIP calls (PC client, iphone client) but?I have an issue with calling external number throught PSTN (certified-asterisk-1.8.11-cert2). I'm having this ?error when making a call: *CLI> ? == Using SIP RTP CoS mark 5 ? ? -- Executing [9000 at local:1] Dial("SIP/3000-00000006", "DAHDI/1/4384019357,10") in new stack [Jun 23 16:18:09]

Hi guys. Does somebody knows how to get the concurrent calls from the dial plan? Or. How can i control not to run more than n simultaneus agi applications? Thanks in advance. rv -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20140710/70b38e21/attachment.html>

Hi! Is possible to use X100p TDM400P, Tdm410p, Tdm400, A400p, Ax400p or any others digium card FXO for use Fax modem? Thanks.

Hey, I'm still waiting for the new file server hardware to arrive so I plan to enable user logins in the meantime without profiles and home directories. Reason for this is quite some pressure from people. The setup on the 2 DCs should be done a day or two. Could there be problems if I configure profiles and home directories some weeks after users logged in for the first time? What if e.g.

Hello Asterisk users, We are having MANY but MANY problems configuring an analog fax machine to work properly on Asterisk, the first thing we do was to plug in the Fax analog machine to the FXS port of the Digium TDM410P, we set echocancel=no on zapata.conf and also faxdetect=yes on general section, but our Asterisk CRASH every time we try to send/receive fax! We are using Asterisk 1.4.21 and

Hello, I am working on a trixbox based system with a TDM410P connected to 3 phone lines from the CO. The asterisk box is on a full duplex 100Mb LAN with some polycom and Aastra SIP phones. In general everything works. the problem I am trying to solve is that if both parties to a call speak at the same time one of the voices gets cut out such that the talker A cannot hear what talker B is

Hi gang, We are moving our computers from a cluster of physical machines to a VMWARE server with virtual machines. We investigated and are looking to replace our TDM400P/TDM410P with AEX410P cards. Can we run asterisk with the DAHDI drivers from one of the Virtual machines or is DAHDI going to have to be a native process on the "REAL" machine? Thanks Danny Nicholas

hi, i just installed 2 new tdm410p's on asterisk 1.4.19 with zaptel 1.4.10. They have the hardware echo cancellers. I am having an issue though, when i talk, it cuts out the other end. So for example, i called up another asterisk box and was listening to the prompts and as they were playing if i said something, it would cut out the other end. so i basically started counting and for the

Nov 12 08:54:27 steerpike kernel: Uhhuh. NMI received for unknown reason a0 on CPU 0. Nov 12 08:54:27 steerpike kernel: You have some hardware problem, likely on the PCI bus. Nov 12 08:54:27 steerpike kernel: Dazed and confused, but trying to continue Would my Digium TDM410P cause an NMI, or is my computer failing? - Mike

Greetings, This may be a dumb question, but here goes. When I was on 1.4.21.2 using Zaptel, I had (at least as far as I could tell) access to line supervision on my POTS lines using a TDM400P/TDM410P. Since upgrading to the DAHDI branches of 1.4 (SVN and 1.4.26.1), I've only been able to duplicate the success of the 1.4.21 functionality once. To test what I'm talking

I have been doing a lot of reading forums and elsewhere but am somehow unable to connect the dots. Here is what I am trying to accomplish initially and then wish for it to grow bigger from here on. I have two POTS (Analog) line that would connect to the Asterisk Box. I have, to begin with 5 IP phones (PoE), all connected to a switch. Asterisk Box with a LAN card also connects to the same switch.

On a BT line, how do I determine whether the number on an incoming call has been deliberately withheld (by dialling 141) or is merely unavailable (e.g. because it originated from overseas or passed through some ancient switching equipment) ? In the first case, I want the caller to be played a message to the effect that we are not at home to anonymous cowards but if their business is

When I call my Asterisk-server from my cell phone on one of the PSTN-numbers that terminate in a FXO-module on my TDM410P Digium card, and in the dialplan the end of a context is reached and Asterisk needs to execute the Hangup()-command, I notice the following : - Asterisk tells me that the conversation was hung up (the log files tell me the command was executed) - On my cell phone I hear