similar to: MGCP error for Cisco 7750 FXO card

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

Hello I have a problem with my MGCP voice gateway. I use D-Link DG104S Boot PROM Version 3.0B38-D Firmware Version 3.0T86-D I tried asterisk v 0.7.2 and I am using latest CVS version now. When I dial a number very fast, or when I use a redial function, my asterisk receives coupled digits. My co-worker called number 245005111, these are a few lines of my debug. The identifier of first digit

I have a Cisco ATA-188 with two POTS phones and latest stable cvs. In any situations with call waiting (existing connection and calling again) the second call cause both calls to drop. This is the same for "internal" extensions and from external (ZAP and SIP). It seems to be a "502 - The transaction could not be executed, because the endpoint does not have sufficient

Hi, I have some problems transfering call from phone to phone with my Asterisk. When I dial Flash I can hear for half a second the dial tone, but it stops suddenly. The other phone hear the on hold music and pressing flash key another time I get back to the previous channel. On the asterisk consolle seems to be all ok, this is whant I can read: asterisk1*CLI> -- Swapping 0 for 1 on

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:

I'm trying to use a 4 port ATA that was designed for use with MGCP 1.0 / NCS 1.0 -- is the channel_mgcp compat with NCS -- anything I can do to make it compat?? This is what happens - below *CLI> mgcp reload Reloading MGCP == Parsing '/etc/asterisk/mgcp.conf': Found Use EXIT or QUIT to exit the asterisk console == MGCP Listening on 10.1.22.39:2427 == Using TOS bits 0 mgcp

Hello, I have just received an MGCP Phone for test purpose and I can't place a call from my MGCP Phone. I can call my MGCP phone from a SIP Phone. Here is my mgcp.conf: ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr = 0.0.0.0 ;[dlinkgw] ;host = 192.168.0.64 ;context = default ;line => aaln/2 ;line => aaln/1 [192.168.10.10] host = 192.168.10.10 context =

Hi. I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk with the next configuration files. '--------------- extensions.conf ---------------------------------------------------- [general] static=yes writeprotect=yes [globals] ap1 => mgcp/aaln/ap200@64.76.148.186 [macro-apl1] exten => s,1,Dial(${ARG1},30,Ttmr) ;exten => s,2,Voicemail(u${MACRO_EXTEN})

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

Does anybody has the expirience configuring Asterisk with Cisco ATA 186 MGCP firmware ? I have Cisco software v3.1.1 atamgcp (Build 040629A) Asterisk 1.0-RC1 On ATA i only put domain test. mgcp.conf looks like this [test] host = 192.168.195.55 context = default line => aaln/2 line => aaln/1 Asterisk CLI shows this: Jul 31 16:05:40 WARNING[135449600]: chan_mgcp.c:485

> Hello all, > Can someone help me on the problem which I have on MGCP phone test . I test mgcp - asterisk- zap. But I got several NOTICE message from rtp.c. > NOTICE[20501]: File rtp.c, Line 221 (process_rfc3389): RFC3389 support > incomplete. Turn off on client if possible > > -- Endpoint 'aaln/1@VG101-1-1' observed '9' > NOTICE[20501]: File rtp.c,

Hi all, I am configuring asterisk in a cable modem network, using a motorola TM401A. I can make calls from the MTA but I can receive, display the following error: -- Executing [1500 at alberti:1] Dial("OSS/dsp", "MGCP/aaln/1 at 0-13-11-82-bd-a.ssw.intercal.net|30") in new stack [Sep 2 00:10:53] NOTICE[28062]: chan_mgcp.c:3572 mgcp_request: Asked to get a channel of

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

I have a DG-104S (which I reset to factory settings, it's DHCP'ing off my network, plugged into the WAN port). The system comes up, and I through the web browser set under Call Agent IP Address to: Notify Entry: dlinkgw@[192.168.1.1]:2427 (192.168.1.1 is the * server) I have RGW Name: and DNS IP addres the DNS IP of the MGCP box and DNS State disabled (not sure what to set it to) --

Has anybody had any luck getting an Adtran Total Access 616 working via the Ethernet port/MGCP to an * box? The voice lines don't seem to be coming up and I wasn't sure if I had something missing. Here's my mgcp.conf file: [general] port = 2427 bindaddr = 0.0.0.0 [10.189.189.31] context=nicktest host=10.189.189.31 canreinvite=no line => aaln/1 line => aaln/2

Hello List, I'm trying to setup MGCP channel with a Centile Media Hub box. My Centile box has 4 ports and I got no dial tone. Can somebody help with this isuue? This is my mgcp.conf and extensions.conf Thanks Daniel. ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 192.168.11.20 disallow=all allow=g729 allow=alaw allow=ulaw [192.168.11.200] context=MGCP

Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ... TRUNK=H323/BYEXTENSION@pstn_gw ...