similar to: Odd ringing conditions

I have a TDM400 with 2 FXS cards, and a Samsung 6100 DECT base station connected to one of the ports. The base station appears to only support UK (BT) style CLIP Caller ID signalling. Does anyone know if it is possible to configure the ZAP channel to send in this format, or alternatively can you recommend a GAP compatible base station which will handle both BT and Bellcore signalling? A search

Nearly got an SPA922 phone working behind a NAT, the phone registers, and I can dial out and have two way speech, on an incoming call the SPA922 rings I answer and the SPA922 shows "Anwsering" but never does and the far end continues ringing until the voicemail answers, this then show as a disconnected call on the SPA922 I'm on the lastest firmware 6.1.5(a) Thanks in advance

Hi All I'm having problems posting to this list, no bounces the mails just dont show any advice how to get the postings through is there filtering? robb

As you my be aware the X100p cannot collect uk caller id, now I have a modem and a perl script that creates a file /etc/asterisk/callerid.txt on each incoming call in the format number,date,time,name over writing each time a new call comes in I can asterisk read this file and populate the callerid for internal phones and cdr? I think it can be done with AGI but don't know where to start

Hi I have looked through the wiki and search the mailing list, but I cannot find a way to intrude on a call, can asterisk do this feature? if so how? Thanks for your help Robb

Hi All I cannot seem to find a way to stop atserisk inercepting DTMF tones and regenerating them even on a zap to zap bridged call is this possible? Thanks Robb

Hi All Just been looking at stats for one of my sites, and I'm conserned about the number of error cause codes being returned from the telco for example 12000 calls processed 131 are cause code 31* normal. unspecified.* 139 are cause code 28 * invalid number format (address incomplete).* 112 are cause code 1 *Unallocated (unassigned) number. *this adds up to about 3% of calls not

Hi, can anyone recommend a Linux based TFTP server to go on an asterisk box? Thanks in advance Robb

So made my first forray into 1.4 and DAHDI and hit a problem. (Not convinced this is a DAHDI issue though...) Testing an analogue line and asterisk sees the caller ID being passed, but then fails to detect ringing. A plain old analogue phone plugged in rings just fine. Console output: == Starting post polarity CID detection on channel 4 -- Starting simple switch on

Hi I have a requirement to bridge Digital ISDN call through an asterisk box but no matter what I setup in the dial plan the second leg of the zap bridge is always set to Transfer Capability of SPEECH, I wondered if any one has come across this and managed to fix it? Thanks in advance for your help Robb

Hi List I'm trying to update to the lastest kernel but I have a dirver that is not inculded in the distrubution, and I had to use the driver disk when installing centos 4.4 in the first place, The driver megasr .ko works fine with the installed kernel but I cannot find on for the updated kernel, any adive would be appreciated. without the updated driver there is a kernel panic on boot due to

Hi I have a problem with a new DECT phone I have bought The key pad works like a Mobile phone where you dial first then pick up the line, but it seems to dail too fast or spuriously, ie 012826736464 show on thew Asterisk console as 0012282677, could any one offer advice how to fix? Also when doing a ZAP bridge to this phone from an outside line the call is very echoy, but not an internal

Hi I have had a Centos 5 installed with asterisk and zaptel for a couple of weeks, I had to reboot eh machine today, and when it rebooted it got stuck at "Starting udev" if I remove thew tdm400 it boots OK, but no zaptel has anyone seen this , and can offer any advice? Thanks Robb

hi all, i have an asterisk install with a digium 4 port fxo card and cisco 7960 sip phones -- running on a compaq Pentium III (Coppermine) at 800Mhz 256KB cache and 1GB of ram. when a call comes in on zap/1-1 for example, the delay between when zap sees the line going to ring state, and when the desktop telephone rings can be as long as 7000 milliseconds (or about 3 or 4 rings on an ear piece).

Hi I'm having a problem where the recall button doesn't work If i press recall before I dial numbers it disconnects me which is what I would expect, but during a conversation if I want to transfer the TDM 400 just ignores the recall Any advice would be gratefully received Thanks Robb

Hi All BT are providing a SIP gateway for PSTN through the BT communicator with Yahoo Messenger, I have done an ethereal trace and found that the BT Communicator side of the software is using SIP, so in theory I could add more PSTN lines to Asterisk for BT using SIP, but I am having problems deciphering the trace so my question is has anyone else tried to get BT Communicator work with

Don't you just hate it when something was working and when you come to use it in anger it's broken :-( Something in the, fairly, recent series of Asterisk updates has broken DIGITAL call passthrough. I've an ISDN PBX behind my Asterisk Box (PRI ISDN comes into port 1 of a Digium Wildcard and the PBX it connected to port 2 via an ISDN crossover cable). This PBX used to be able to

Hi All, Channels 25-28 on a customers PBX are regular Zaptel FXO cards that are hooked into 4 incomming phone lines. They are all in a group to do automatic rollover for outgoing calls (if channel 25 is being used, dial on channel 26, etc.). Sometimes when a user is dialing a number, instead of bridging to one of the FXO cards it goes and rings to Zap/1-1. This doesnt occur all the time but some

Hi, What do I need to do to get asterisk to NOT pickup a Zap channel when it rings? The channel in question is used for outbound calls only, and all incoming calls are answered by an analog phone elsewhere in the building that does not run through asterisk... so.. either make it not answer.. or make it delay for like 90 seconds.. I've tried wait's.. but it still seems to pickup the

Hi all I ahve been having problems loading the wcfss and wcfxo drivers I get an error message invalid argument and something about post install insmod failed the currently load modules do show the drivers loaded but asteris won't start lsmod root@slackware:~# lsmod Module Size Used by Not tainted soundcore 3332 0 (autoclean) wcfxo