similar to: newbie question: Meetme

Hi Peoples I am having problems with meetme, in that it responds with "conf-invalid" when I dial a conference number. I notice that there is a note with regards to ztdummy, and the need for that to be loaded. Is this still the case? Is meetme dependent on this module? I do NOT use zaptel cards in my system, and there for zaptel is not loading. Can anyone shed some light

Any thoughts on the following? I am running asterisk from CVS (downloaded yesterday's version, just to be sure) on a test system with no digium cards in it, so I have installed ztdummy (see logs and screenshots below) as a timing source. When I call the music on hold extension from a Sipura Sip connected analog phone, I hear nothing and start getting Warning[98310]: chan_sip.c:674

Hi, I am using Debian OS kernel 2.6.22-3-amd64 and zaptel driver 1.4 with ztdummy module for meetme application. I use meetme with SIP channels. I have such problem that when one connects to the conference voice is "cut". Each voice sequence is disturbed. Does any one have similar issue and could give me some advice?? my extension.conf for meetme: ;switch =>

When I call meetme: exten => 1000,1,Answer exten => 1000,n,Meetme(|||d) Asterisk is complaing with: -- Executing Answer("IAX2/xxx.yyy.142.204:4569-2", "") in new stack -- Executing MeetMe("IAX2/xxx.yyy.142.204:4569-2", "|||d") in new stack -- Playing 'conf-getconfno' (language 'en') Warning, flexible rate not

Hi, I don't have a zaptel device for conferencing. I read from the lists, that ztdummy and zaprtc need to be installed to get conferencing. I could able to compile successfully with ztdummy and when i receive the call it says, -- Goto (13732,s,1) -- Executing MeetMe("SIP/-08118800", "1234") in new stack == Parsing

I have ztdummy installed: Module Size Used by ztdummy 3464 0 zaptel 218756 1 ztdummy crc_ccitt 2176 1 zaptel ohci_hcd 16388 0 floppy 49028 0 pcspkr 2180 0 piix 8580 0 [permanent] ehci_hcd 24456 0 uhci_hcd 26256 0 rtc

Hey folks, Using FreeBSD 5.2.1 and I've got the current zaptel driver installed from ports (0.8_1) and current ports asterisk (1.0.1). I've set options HZ=1000 in my kernel config, recompiled and rebooted and as far as I can tell, I've done everything right but when I try to use the conference, the audio is very delayed, choppy and segmented -- totally unusable. At the

Good day all I've installed asterisk with sip on my LAN,no special cards,if done sip.conf and extensions.conf and all work 100,I'm using x-lite as a client. I'm trying to do conferencing.What I did was to has out the meetme.conf looks like [rooms] conf => 9876 conf => 2345,9938 and extension.conf exten => 9876,1,MeetMe,9876 When I go onto x-lite and type 9876 it gives me

Hi, is it and how is it possible to live monitor (barge - in) a SIP to SIP call without any Zap Interface? I am using asterisk 1.0.5 with chan_capi from Junghanns and SIP clients. I was looking for chan_spy application but it seems to be no longer available. Bye, Sven -------------- next part -------------- An HTML attachment was scrubbed... URL:

Yes. Tim Thompson http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: CW_ASN - Gus [mailto:cw_asn@fibertel.com.ar] Sent: Wednesday, October 22, 2003 1:12 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Meetme Do you have ztdummy or zaptel device in your system? ----- Original Message ----- From: "Panny Malialis"

Does anyone know where to disable rtc support on redhat 9.0 using make menuconfig? I thought I disabled it but still got the following error when trying to make zaprtc: zaprtc.c:109: storage size of `rtc_irq_timer' isn't known zaprtc.c:719: storage size of `rtc_fops' isn't known zaprtc.c:107: warning: `DECLARE_WAIT_QUEUE_HEAD' declared `static' but never defined make: ***

I do not have any zaptel hardware on the Asterisk box, I could not have meetme functioning. I did modify the Makefile in zaptel directory on line 168 by including ztdummy as one of the modules to compile in. The error message from the concole: -- Executing MeetMe("SIP/1002-e9ca", "4700") in new stack == Parsing '/etc/asterisk/meetme.conf': Found

Hi, when I build zaptel-1.2 and asterisk-1.2 I can modprobe ztdummy and start asterisk to be able to use MeetMe(). When I build zaptel-1.4 and asterisk-1.4 I can modprobe ztdummy and start asterisk but I am not able to use MeetMe(). What do I miss? Stefan -- amooma GmbH - Bachstr. 126 - 56566 Neuwied - http://www.amooma.de Let's use IT to solve problems and not to create new

I need a timing device for the DL360G2 for conferencing and meetme. For a timing device I have 2 X100P cards but neither will work in my DL360G2. The system will not even boot with either card in the system. Other PCI cards seems to work fine. I called Digium support and was told that there must be a conflict between the card and my Compaq DL360G2. I then moved on to ztdummy. I'm sure the

Hello System: Debian etch with kernel 2.6.18-4-686 or 2.6.18 custom. Asterisk Version: SVN-branch-1.4-r55483M Zaptel Version: SVN-branch-1.4-r2302 modules all ok in compilation time. And modules loaded: ztdummy 5928 0 rtc 13364 1 ztdummy zaptel 181540 1 ztdummy crc_ccitt 3200 1 zaptel In /dev/zap directory I have:

We have recently started making more frequent use of the meetme conference of our * system. We are using v1.0.8 with a 2.6.11 kernel on our system. We generally have 4 callers in it: two with the gsm codec and 2 with g729. Initially, the conference works fine and there is little latency. After about 15min., though, the latency is very noticable and by 25min it's unbearable. If we all leave

Hi I want to set up * as a conference bridge. I would like to be able to conference is SIP calls (up to 12) I am looking through all available documentation for * to get info on how it is done. No luck so far. Can somebody direct me to the info in this subject? Thank you Serge _________________________________________________________________ Protect your PC - get McAfee.com VirusScan Online

Hi there, I know this question is kind of stupid. But, I don't know anywhere else to ask. I've received some answers when I asked about the need of having a zaptel interface to make the meetme application work, that said that it was better to have a real hardware then the zaptelrtc software modules. So, my question is, would any of the following cards work with the meetme

I try to use meetme app after reading manual i compile and install zaptel with ztdummy when i make lsmod i have ztdummy 2532 0 (unused) wcusb 20064 0 (unused) zaptel 179168 4 [ztdummy wcusb] usb-uhci 26348 0 [ztdummy] usbcore 51616 0 [wcusb usb-uhci] after it i recompile asterisk and after it i have

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, As I understand it, IAX2 trunking requires zaptel timing. Zaptel timing is provided by Zaptel cards, ztdummy or ztrtc. ztdummy requires usb-uhci and ztrtc can't run on smp systems. So if you only have smp systems with ohci and no zaptel cards (because it's a sip/iax2 gateway) then you're screwed? - -- Regards, Tais M. Hansen