similar to: NEWBIE looking for advice.

All, I need help. I have an (actually 2) Adtran TA750's with 8 FXO ports. I get a terrible buzz on every FXO port. If I unplug the Adtran and put an analog phone on each incoming line, I have no buzz. I also have 2 Carrier Access Access Bank I's with 12 FXO ports. When I plug the same analog lines into either one of those, no noise or buzz whatsoever. I went so far as to move the TA750

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

Hello. I have been going thru the wiki and asterisk related sites and have not been able to find any documentation about how to configure an Adtran TA750 channel bank. The remote disconnect supervision doesn't seem to be working, when the remote caller hangs up asterisk takes up to 30-45 seconds to hangup the call. Can somebody help? Thank's

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Can anyone share any advice / documentation on how to configure a Tellabs 2572 T1 echo canceller? I connected one between a T100P and an Adtran TA750 FXO/FXS channelbank, but when echo cancellation is active I get a LOT of snap-crackle-pop (and other problems) on the line. The 2572 has a bunch of configuration options and they're impossible to guess without documentation, which I cannot find

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

Folks, I recently obtained a Western Electric multi-line phone and am seeking help with getting this beast working with *. The interesting stuff in my * implementation consists of a T100P card, a TDM400P card, and an Adtran TA750 channel bank with three quad-port FXS modules and a quad-port FXO. The TA750 is wired to a 24-port Cat 5 patch panel via a 25-pair Amp cable. The phone is a model

Hello, I need help in creating a simple PSTN Gateway. This is the scenario: -I have one client sending me VoIP traffic (they don't have asterisk, so IAX is out of the picture for me) and I need to validate that traffic (only accept calls coming from his IP). After that I would terminate the calls to the PSTN network and keep logs for billing purposes. -I have a TE405P board and

Hello, I have been researching Echo Can's for a while now, and wanted to post this out to the list to solicit feedback (and if my assumptions are correct, hopefully help others out)... If anyone out there knows anything about wiring up an Echo Can, and my outline below is incorrect, please let the me/list know.. I have posted the Documents I received from Tellabs at:

Rich, Thanks a bunch, totally understand now and that actually makes total sense. (no need for schematics). This also explains why I used an TA750 to go into a Nortel MICS system, using FXO and no buzz. Totally balanced load from the analog ports on the Nortel across the 5 feet of CAT5 to the FXO on the adtran. Now I need to get rid of some Adtrans --- Anyone lookin to buy? :) Thanks

I believe it is not fiber, but I am not sure. I am going to take one of them home tonight and hook it to my POTS line there, which for sure is not fiber. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Michael Welter Sent:

Hello, We have a high volume of incoming and outgoing calls that come in via our analog POTS lines connected to FXO cards in an Adtran TA750. This is connected to a T100P. We are using Polycom IP 500's. The problem we are experiencing is, on frequent occasions, when someone dials out, there is another person who has just dialed in. I have had this problem at my house before (without an *

We currently have a 15-phone system using Asterisk, a combination of analog phones/Grandstream HandyTone-286 and Grandstream BT101s, and 4 X100Ps connected to analog lines. The system works well except for the occasional echo problem. I have all the echo parameters configured, removed all the extra incoming analog lines except to the PBX, etc. following all the advice on the wiki and on the

I've been trying to get a Win 2000 RAS server working with my asterisk PBX for quite some time, to no avail. I've googled, I've tried loads of configurations, I've rewired phone lines, and still I am not winning the battle. Here's my config. PRI->T400P->Asterisk->T400P->Adtran 750(L36 Firmware)->RAS Server. I have 4 Zap channels signalled FXO_KS to the 750

Hello, I new to this, but with the help of mailing lists archives and IRC I am able to build my PBX. Thanks to all who had help me to reach till here. I am stuck at a point where I can't find the solution on mailing lists or even on IRC. I have individual 4 DID (Direct Inward Line) coming from Telco and terminating into TA 750 to FXS card. Many of them told that Phone instrument terminates

I have two Adtran 750's connecting our analog phones to asterisk. On occasion, I get a channel that gets "stuck" off hook. 'show channels' shows: Zap/27-1 (longdistance s 1 ) Rsrvd (None) (None) And will just stay like that until the phone is manually picked up and hung up again (or asterisk is stopped/started). I guess this is a function of an unclean hangup (being

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Ok, the Zhone sucks and the Adtran 750/850 seems to be a little too expensive. Can anyone recommend a decent channelbank that won't break the bank? TIA, -- Troy Settle Pulaski Networks http://www.psknet.com 540.994.4254 ~ 866.477.5638 Pulaski Chamber 2002 Small Business Of The Year

Rob at draughon.org writes > I recently obtained a Western Electric multi-line phone and am >seeking help with getting this beast working with *. > > The interesting stuff in my * implementation consists of a T100P >card, a TDM400P card, and an Adtran TA750 channel bank with three quad-port >FXS modules and a quad-port FXO. The TA750 is wired to a 24-port Cat 5 patch >panel