similar to: iax2 trunk

hi all, I am trunking via iax2 2 asterisk serverses if both of them have static ip addresses, I can connect them using no password, password or auth rsa with a pair of keys. If one of them has dynamic ip address and need to register on the other server, I can connect them with no password, but I am not able to do that using keys. The question is: which is the right register syntax to use when

I am trying to set up an IAX2 trunk between two servers. Server A has the following in iax.conf: [general] ... [ServerB] type=friend trunk=yes host=dynamic secret=myPassword context=myContext Server B has the following in extensions.conf: [outgoing] exten=>_40X,1,Dial,IAX2/ServerB:myPassword@x.x.x.x/${EXTEN} I am using bmtools to monitor the bandwidth usage, and I am not seeing a difference.

Hi, I?m trying to get app_festival to work. I got the source from the Debian woody package of festival-1.4.2 and applied the patch that came with * sources it applied fine; then I made the debian package and installed it. I have this on extensions.conf: exten => 6700,1,Festival(Hi there how are you doing ?) When I dial 6700 I hear nothing and then * hangups: -- Executing

Hi, I am trying to connect two Asterisk servers using IAX2. Everything works fine when I couple them within a LAN segment, but not when I connect them using WAN connections. I made sure that the routers' ports are mapped properly and checked this with additional ssh rules. ServerA is a Raspberry box with the vendor's Asterisk version 1.8.13.1 and ServerB is normal CentOS 7 box with

Here is my Configuration PSTN -> Cisco AS5350 -> SIP -> ASTERISK -> SIP -> ATA186 When I call from the pstn to the ATA, the ATA rings but I don't hear anything on the calling side until the call is picked up. When I call from the ATA, everything seems to work fine. When I bypassed ASTERISK, everything seems to work fine. Anyone know what I might have configured wrong?

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I was just measuring the bitrates of a couple of codecs via iax. I'm getting much higher numbers than expected, so maybe I'm doing something wrong? Measured with iptraf, values displayed are: codec: measured bitrate (bitrate according codec definition) gsm: 52 kbps (13 kpbs) alaw: 154 kbps (?) speex: 57 kpbs (24 kpbs) Seems a little

Hello, I have 5 digium's g.729 codecs and succesfully register with asterisk, I have incomming call from my cisco AS5300 to Asterisk through IP. But Asterisk always use g711 ulaw instead of g.729. When I disable all other codecs other than g.729 in both cisco and asterisk, calls get dropped once connected. The codec list show on my cisco AS5300 for g.729 are: g729r8 g729br8 I suspect that

Am using Asterisk 11.2 in one location and 11.1 in another location. when I trunk between two servers, the status is unreachable. But with different server with 11.2 and 11.2 it works fine. I tried both IAX and SIP. the trunk in sip.conf what i have is, [serverb] type=friend username=serverb secret=serverb host=10.10.10.5 port=5060 context=default insecure=port,invite dtmfmode=rfc2833

Please forgive me my ignorance ... I've spent two days trying to find out something about the format of the default configuration file, which CCM produces. The only example I have so far is the one from the chan_sccp source. There were tons of references on entering the callmanager commands on a cisco command line - which I don't have (don't need thanks to chan_skinny + chan_sccp).

Hey all...for whatever reason my caller id doesn't appear to be working. My setup is simple (Wildcard FXO and thats it) and I'm just expecting the Caller ID to show up on the console. I'm seeing this: *CLI> -- Starting simple switch on 'Zap/1-1' NOTICE[262161]: File callerid.c, Line 238 (callerid_feed): Caller*ID failed checksum NOTICE[262161]: File chan_zap.c, Line

When dialling in and dialling my extension, when answered I get " Read_channel ## vpb/1-3: Setting record mode, bridge = 0 WARNING[20499]: File chan_sip.c, Line 1111 (sip_write): Asked to transmit frame type 8, while native formats is 4 (read/write = 4/4) == Spawn extension (default, 1004, 1) exited non-zero on 'vpb/1-3' -- hangup on vpb (vpb/1-3) -- Hungup on vpb/1-3 complete --

Hi, si posible on SIP phones to have the dial tone after 9 like on the FXS card? I set ignorepat => 9 on my extensions.conf... Best regards, Chris HARIGA

I am wondering if it's possible to use a bunch of cards in a PCI backplane instead of going out to the extensions with T1 and then and adapter. How are people connecting to large amounts of extensions?

I've got 2 asterisk servers on the same box: ubuntu 10.04 lucid. I have not been able to send useful callerid info between them (callerid becomes "serverB"). serverA register statement: (serverB has the exact opposite statement) register => serverA:serverApassword at IP_of_serverB_nic/serverB users.conf of serverA: users.conf of serverB: [serverB] [serverA] type=friend

Hi all! Please I need someone that have already done an H.323 - SIP gateway to help me with some problems. I can stablish calls from a SIP telephone to a H.323, but I can't do vice versa... (problems with port 1719- when the gatekeeper tries to contact with asterisk at this port, it is unrecheable...). Please someone can help me? Regards, Mireia

I'm trying to get musiconhold to work w/ my Asterisk system, and I'm not having much success yet. First, I noticed that nothing happened even after I had enabled all of the options in zapata.conf & setup a sample extension in extensions.conf. Then I read something about how Asterisk uses mpg123 to play the files. I discovered that this had not been installed on my system, so I

Hi, I''m having trouble getting puppetrun to work, it returns: # puppetrun --debug --host serverb debug: Puppet::Network::Client::Runner: defining puppetrunner.run Triggering serverb debug: Calling puppetrunner.run warning: peer certificate won''t be verified in this SSL session err: Could not call puppetrunner.run: #<RuntimeError: HTTP-Error: 500 Internal Server Error >

Hi all, can somebody explain this ? Thanks, Thomas. ******************************************* beroNet technologies GmbH Dipl.- Ing. Thomas H?ger Potsdamer Str. 18 A 14513 Teltow FON: +49 (0) 3328 3077731 FAX: +49 (0) 3328 334779 Email: thomas.haeger@beronet.com *******************************************

Hello List, i would like to copy/mirror/rsync the backup files from ServerA to ServerB. Since i must assume that ServerA is hacked (public server with a few services), i would like to "pull" the files to ServerB (save server with no services). That means i do something like: rsync -avz ServerA:/backup ServerB:/backup IF ServerA gets hacked and the files get zeroed out (every file