similar to: SIP X100P Echo Problems

Hello, I resolved my echo issue using grandstream/estara etc etc sip phones and wcfxo interfaces from digium. I swapped out my via kt400 based msi kt4vl motherboard for an asus p4pe? i845? based motherboard and the echo has completly gone away along with aggressive suppressor option in the makefile. I hope this helps others. Brian J. Schrock Anistone Technologies, LLC 6926 Avery Rd. Dublin, OH

> Brian> Hello, I resolved my echo issue using grandstream/estara > etc etc Brian> sip phones and wcfxo interfaces from digium. I > swapped out my Brian> via kt400 based msi kt4vl motherboard for an > asus p4pe? i845? Brian> based motherboard and the echo has > completly gone away along Brian> with aggressive suppressor option > in the makefile. I hope this

Everyone, Just thought I would drop a line telling everyone here I have the software RxFAX/TxFAX up and running without any real problems. I did have to..... RH 9.0 1) Install an audio devel rpm 1) install libtiff from source, and copy over a bunch of include files to /usr/local/include 2) build/install spandsp 3) move app_rxfax.c and app_txfax.c to apps/ dir in asterisk source tree. 4)

Hello, Does anyone know what may be causing this? Asterisk was built from cvs tonight. Ztcfg also says us is an invalid tone zone. Anyone got some information on what this is, why is it happening, and possibly some solutions? [root@anistonetech zapata]# asterisk -f -d DEBUG[1024]: File config.c, Line 653 (__ast_load): Parsing /etc/asterisk/asterisk.conf DEBUG[1024]: File config.c, Line 653

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hi, We are looking at consolidating our lines with PRI. This will allow the elimination of many fax lines. Some of them will be replaced with this type of config ... PRI * IAX * Channel-Bank FAX We will have daggressor suppressor enabled. Is anyone doing this and should I expect smooth operation? John This e-mail was scanned and found clean by Monroe-Woodbury CSD Antivirus.

Hello, How would I go ahead a record all phone calls into and out of my asterisk server. I know the legality issues behind it, but I could always play a recording to let people know they will be recorded. Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-537-2817 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hello, I have my sip stuff seemingly working fine as well as my zaptel stuff working great... But I have a problem with sip registration timers (I'm guessing here). In my extensions.conf file I have this... exten => 2244,1,Dial,Zap/2|25 exten => 2244,2,Dial,Sip/brian|25 exten => 2244,3,VoiceMail,u2244 But if I close my sip phone and a call goes through it will still wait the 25

I'm wondering if anyone knows of ISPs with service that has QoS features that would be good to use with VoIP stuff. Granted, the QoS would only be supported as long as you stayed within their network, but it might be better than nothing. --Eric

I have a simple problem with sialing a SIP device. I'm SURE it's a syntax problem, but I dunno what it might be. Here are the debug messages: == Accepting call on 'Zap/1-1' ("PENSACOLA, FL" <8503846785>) -- Executing Goto("Zap/1-1", "2111|1") in new stack -- Goto (default,2111,1) -- Executing Dial("Zap/1-1",

Hi, I did not find any hints in the web where to configure/setup/manipulate the rx/tx ring buffer allocation within dom0 for xen-unstable, maybe someone here can nudge me towards the right knob. The problem: when booting a handful of domUs and connecting them (comprising a small experimental IP network with links and nodes etc.), some interfaces that have been given by the configuration files

Hello everybody! I have some problems with my Astersk. I have an analogical OpenVox card and A Billion ISDN card (with mISDN). I load the modules with modprobe zaptel and modprobe wctdm. When I run ztcfg -vv I have this: Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No

Has anyone else experienced a problem with the LED for span 1 on a TE410P or TE405P? I had a TE410P on which the span 1 LED would not light red, but once the span was connected, it did correctly light green. I RMAed the board to our UK distrbutor and received a replacement. However, the replacement board displayed the same problem! Wondering if it was related to the computer I was putting it

Anyone else seen this eth-device and what brings it up? [root at oh1mrr etc]# ifconfig __tmp1192348344 Link encap:Ethernet HWaddr 52:54:AB:DD:2E:D1 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2094689 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645734 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX

Why standard Centos 5.2 kernel does not have a module "pata_via." I have an old motherboard and IDE drive. The standard kernel does not work. Kernel include a module "pata_via" only in centosplus. It is a bug?

Hi, does anyone have any idea whether VIA VT6102 "Rhine II" and Realtek RTL 8100 Ethernet chips are supported by FreeBSD? The hardware list for supported chips does list 'VT86C100A "Rhine II"' but according to VIA website VT86C100A is actually just "Rhine" and it is obviously not the same chip. (The 'VT3043 "Rhine I"' chip mentioned in

All, I have a problem with a new Seagate hard disk. The problem occurs when i go to install CentOS, i insert the cd and start the boot up process, when it gets to the section where it detects the hard disks, the driver is seems crashes, the message it produces complains about no one caring about a interrupt on IRQ11. The hard disk is a Seagate 200GB 8MB SATA150 NCQ drive, on a SilliconImage

One system I have is configured thusly: AMD Duron 1200 (I have frequency restrictions in this application, and must stay below 1.3GHz or must be above 2.0GHz, and the 1200 fits nicely in our interference plan; besides, I was given the chip, and it's fast enough for the application). Soyo DRAGON KT400 motherboard, 512MB DDR RAM (DDR266). Silicon Image SATA interface card. Machine boots

Hi , I'm disperated I've recently installed FreeBSD 4.8 ,and all at the first look was ok , this was only a try in a small partition , and now I have decided to install it in a bigger partition , so I've downloaded the 5.1 ISO (to give it a try too) and I've tried to BURN it with "burncd" . Now, I've noticed that in the DEV directory there are the devices

https://bugs.freedesktop.org/show_bug.cgi?id=75569 Priority: medium Bug ID: 75569 Assignee: nouveau at lists.freedesktop.org Summary: [nv34] [v3.14-rc3] DMA_PUSHER get 0x00029044 put 0x000184d0 state 0x80000040 (err: INVALID_CMD) push 0x00000000 QA Contact: xorg-team at lists.x.org Severity: