similar to: Ascom Ascotel 2050 & Fritz PCI Card (Capi)

hello! one thing i'd like to see in OpenSSH is (optional) IDEA algorith support. this would be useful especially in an environment which has a mix of old ssh v1.2.x and OpenSSH installations. according to Ascom non commercial use of IDEA is free (http://www.ascom.com/infosec/idea.html). also, there are countries (e.g. Finland) where IDEA is not patented. here's a patch suggestion for IDEA

Just to make sure, what's the goal here? Is the goal 1) to have a fast Opus implementation or are you 2) looking for an interesting FPGA implementation project? If 1), then an FPGA is most likely not necessary since Opus is not computationally expensive. If 2), then it depends on the desired size of the project and the desired quality. The simplest encoder possible is indeed simpler than the

The originating PRI system passes the entire dialed number in the d-channel setup frame, thus the concept of a wait time for additional digits is meaningless. Progressive digit gathering implies that the signalling is occuring 'in-band' as would be the case with DTMF signalling on analog lines. You need to look in the Ascom and find the configuration table that lays out the dialplan for

Skipped content of type multipart/alternative-------------- next part -------------- Nov 21 14:17:47 VERBOSE[32580] logger.c: <-- SIP read from 172.25.103.222:5060: INVITE sip:1715;phone-context=exp_net.ascom@ascom.be:5060;maddr=172.25.96.48;transport=udp;user=phone;x-nt-redirect=redirect-server SIP/2.0 From:

Hi, We would like to use the OPUS codec @ 16 kHz sampling rate and max 32 kbps. What about implementing an OPUS coder and decoder in an FPGA? Has this been done? Would either coder or decoder more suitable for FPGA implementation? Best regards Fredrik Bonde -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Since our device can only handle the Celt part of Opus (due to a MIPS limitation), we have two questions: 1. Is it possible to via SDP force the remote party to send a specific mode of the 32 different possible modes or to force the remote side to use CELT only? 2. In the reference implementation of Opus it looks like the only way to force the encoder to use CELT only

I'm not aware of an FPGA implementations yet. You could be the first! An encoder implementation would be much easier, because there are almost no rules about encoders. An encoder is free to behave any way it wants, so you could implement a very small subset of Opus and still have a compliant (and useful) encoder. A decoder implementation would be much harder, because decoders are required

On Thu, Nov 14, 2013 at 12:51 AM, Fredrik Bonde <Fredrik.Bonde at ascom.se> wrote: > 1. Is it possible to via SDP force the remote party to send a > specific mode of the 32 different possible modes or to force the remote side > to use CELT only? No, and if you cannot decode opus completely (all modes) your device is not conformant with the Opus specification. I'm

hi all this potential customer has some 70 ascom office 30 phones, and wonders if it's usable with *. Does anyone know if it is? I currently don't have one myself, so I can't test it... roy

Hi, I am wondering whether I can use Asterisk as SIP/H.323 Signalling Gateway. The setup I envisage looks as follows: H.323 end-point ---------(ETH)--------- Asterisk ---------(ETH)--------- SIP Proxy/Registrar ---------(ETH)--------- SIP end-point (ETH: Ethernet) In principle, Asterisk would just be used to integrate H.323 end-points into a fully SIP-based core-network. Hence, there

Is it just me or are there problems? The list has just shutdown over the last 24 hours :( David

Hi, Does anybody have an idea on how to realise ad-hoc conferencing with Asterisk ? Although Asterisk MeetMe and maybe a procedure with Call Holding could somehow come close to ad-hoc conferencing, it doesn't seem to be the right way to do it. Any experience with ad-hoc conferencing using SIP in general as well as with Asterisk? Thanks, Joerg

hi, we are currently planning are large site which will migrate from an old siemens hicom pbx to asterisk. the customer is currently using a paging system (small receivers which display a callback number and a base station (transmitter) with several antennas at the site) the problem is, that the currently operative base station uses 4 ISDN BRI interfaces. But the protocol is old germany 1TR6

Guys. I know there are wifi sip phones out there but I have a question, are any of these phones "anti explosive"? By that I mean, there are certain regulations about phones or cel phones that are not recommended to operate in environments like gas stations due to sparks and the chance of ingiting gas fumes. Are there any wifi sip phones out here that have complaince with regulations to

It may have gone to sleep. Chris Cooper Systems/Network Administrator EFC International 1940 Craigshire Blvd St. Louis, MO 63146 US Phone - 314-439-4325 Fax - 314-439-4443 Mobile - 314-402-8912 - -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of asterisk-users-request at lists.digium.com Sent:

Hey folks, I have a T100P card with a PRI; when doing outbound dialing over the PRI, I can use SetCIDNum(2024561414|a) to force caller ID to display as "The White House" on a land line. This is apparently done as a reverse lookup by Verizon, as I do not hand the PRI the words "The White House" -- 202-456-1414 is an actual White House number. Using SetCIDName("Flying

Sorry that I wrote in german : Ich benutze asterisk mit dem zaphfc Treiber. Jetzt hab ich folgendes Problem, habe 2 ISDN-Telefone angeschlossen. zaphfc im nt-mode. Anrufe von ausserhalb per sip (sipgate.de) kommen an. Wenn ich aber intern zwischen den zwei Telefonen (Ascom Eurit 30) sprechen m?chte geht das nur wie folgt : Erst die Nebenstelle w?hlen und dann den H?rer am Telefon abnehmen.

All, has anyone any experience in using Wifi smartphones as SIP clients? Does this work properly? What models/brands are optimal for this (in terms of ease of use, battery life etc)? Thx!! B.

Hi We interfaced our ASCOTEL PBX to Asterisk. by EuroISDN PRI , DSS1 It works fine on channels 1- 15, but on 17-31 the miststood each other. Asterisk speaks in Timeslots, the PBX in B-channels The signalling is ok, but the bridging is shifted. The first incoming connection is bridged to "nirwana" also no indication is hearable, calling a second internal subcribes bridges them to the

Hi I want to connect a Windows machine over TAPI with the Asterisk PBX. So is it possible to connect the Windows machine directly to Asterisk (Zaptel card)? Thanks Harry Baron