similar to: FW: asterisk call waiting X100P -> MGCP ata 186

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one

Does anybody has the expirience configuring Asterisk with Cisco ATA 186 MGCP firmware ? I have Cisco software v3.1.1 atamgcp (Build 040629A) Asterisk 1.0-RC1 On ATA i only put domain test. mgcp.conf looks like this [test] host = 192.168.195.55 context = default line => aaln/2 line => aaln/1 Asterisk CLI shows this: Jul 31 16:05:40 WARNING[135449600]: chan_mgcp.c:485

Hi there! I installed the BudgetTone (GrandStream) on my LAN without any problems. Then, I moved it to another location using a D-Link NAT. I opened 5060 (SIP) and 5000 to 5008 for RTP. I also fixed the IP address of the BudgetTone. When I receive a call on my Asterisk, it would ring my FXS as before. However, after I pick up, it hangs within a few seconds (Hungup Zap1-1 in the log). The

Hey guys, can you shead some light on this? I will copy my mgcp.conf and post below, but here is the problem. I can't get call waiting to work with my MGCP device. I already have one call going, and I can hear the second call come in, I flash over to it, but all I get is a dial tone, * puts the 1st call on mute/hold, but I never get the second, and it terminates. I flash back over and pick

I'm using app_festival to speak some text to callers. I'm having two problems with this. The first is with IAX calls (I've not tried others) the first few seconds of the speech is garbled. The second problem I'm having is the the volume of the speech IS VERY LOUD. I tried putting the following in the siteinit.scm but it didn't seem to make any difference. (set!

Hello list, i am using: asterisk CVS-10/13/03-11:54:33 chan_capi-0.3.0 ATA-186 V2.16.1.ms over MGCP Situation: ISDN calls ATA ISDN speaks with ATA ATA-Phone presses Flash and speaks to another one (SIP/snom200) ATA-Phone hangs up ISDN talks to SIP/snom200 snom200 hangs up The incoming extension of ATA keeps busy for a time (20 sec?), even its not off-hook anymore! Any ideas? -- Swapping

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

Hi all: Very disappointed, finally I left the attended call transfer with ATA 186 using SIP. With image 2.16-1, ATA sens '486 - Busy Here' when trying to transfer the call.. I consulted with Cisco guys and accepts that some problems with this service exist. Soon as I can I will try using MGCP. My doubt now is if somebody proved the DynExtenDB application. I read some commentaries but

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

Hi, I would like to use the asterisk box with zapta card to enable some conferencing. I would like to use only TDM connections without VoIP. I'd like also use the Meetme app. I have some questions: 1. Does any one use it for a few conference rooms at ones ? 2. Is it possible to restrict the number of users connected to one conference room ? Regards. Pawel.

We are working on a new implementation of asterisk. We are using a fiber-served WorldWide Packet switch at the home that incorporates a VOIP T2 switch that feeds 2 POTS connections. We are told that the T2 is programmed with code that follows the PacketCable spec. This version has a problem with the 'congestion' message which is based on the MGCP RFC (2705) spec. This causes the T2 to

hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,

Hello everybody! I have an Asterisk 1.2.12.1 server with SIP as the VoIP protocol. What I want to do: I want to talk to the "outside world" via MGCP. I suppose I must set an MGCP peer to route outgoing calls. So, I must set the endpoint syntax of the Asterisk server (Asterisk will act as an MGCP gateway and will talk with an MGCP Gatekeeper) and with other MGCP gateways via

I am trying to dial a mgcp extention from my sip phone and i am getting this error message. anyone got any idea? error I> -- Executing Dial("SIP/2204-5dc2", "MGCP/aaln/1@10.0.1.150") in new stack May 19 22:30:01 NOTICE[1251156800]: chan_mgcp.c:1104 find_subchannel: Gateway '10.0.1.150' (and thus its endpoint 'aaln/1') does not exist May 19 22:30:01

Hi everybody, I have a MTA from Terayon that I try to make run with Asterisk using MGCP channel. The device is running with MGCP 1.0 NCS 1.0 Each time Asterisk try to send a Request (Request Notify, Audit Endpoint....) the device returns error 510 "Protocol Error" Does anybody have already meet this problem and provide me support to make run it ?! (I have already try to change

I have 1 IP phone (Swissvoice IP10S) and 1 POTS phone. When I dial the number for the IP phone off the POTS phone, the IP phone rings. But when I pick up the handset on the IP phone, I get a busy signal and this message on *: Aug 23 09:38:57 NOTICE[1142106560]: chan_mgcp.c:2243 handle_response: Terminating on result 502 from svip10@00059002042b-1 Here is the entire session. svip10 is the 1 and

Hello I have a problem with my MGCP voice gateway. I use D-Link DG104S Boot PROM Version 3.0B38-D Firmware Version 3.0T86-D I tried asterisk v 0.7.2 and I am using latest CVS version now. When I dial a number very fast, or when I use a redial function, my asterisk receives coupled digits. My co-worker called number 245005111, these are a few lines of my debug. The identifier of first digit

Hi, I have the following situation: I've installed Asterisk at Machine 1 (M1 - IP: 192.168.1.145) and X-Lite (X_lite-Xten-Win32-1103m.exe from www.xten.com) at Machine 2 (M2 - IP: 192.168.1.100) and Machine 3 (M3 - IP: 192.168.1.200). I need to catch the SIP and MGCP messages that will appear when M2 calls to M3 and vice versa. The SIP messages are working (I don't have problems with the

Hi I have asterisk 1.4 I want to make a MGCP trunk as a client to connect to a provider who is using MGCP protocol, he provided me with user & password, I tried a custom trunk: MGCP/$OUTNUM$@user:password at 66.152.163.106:4000 Not seems to help, Any suggestions plz?