Displaying 20 results from an estimated 400 matches similar to: "3 fritz-cards pci"
2005 May 22
0
Trouble using two Fritz ISDN cards in one machine
Hi,
I'm heaving trouble using two Fritz ISDN cards in one machine.
I followed "http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO" and i
think everything works great.
cat /proc/capi/controller shows:
1 fcpci running fritz-pci A1 3.11-02 0xb400 5
2 f2pci running fritz2-pci A1 3.11-02 0xa400 10
The asterisk CLI shows:
*CLI> capi info
Contr1: 2 B channels
2005 Mar 28
1
Kernel panic loading second fritz card
Hi Everyone,
Long time reader, first time poster.
FINALLY got my First AVM Fritz Card up and running under Centos 3.4
Installed the second....modified the drivers etc as per the instructions
found at the wiki
System boots
Modprobe capi
all good
modprobe fcpci
all good
modprobe f2pci
the kernel then goes into Panic
If Modprobe f2pci before fcpci the kernel still goes into panic.
2005 Aug 03
1
Is it possible to use CHAN_CAPI with ZAPHFC enabled card ?
I have an ISDN card, Billion ISDN PCI Card
I tried to use the ZAPHFC, I patched the kernel, I did anything (also
followed reccomandation on use on Suse Linux Professional 9.2 --my box is)
using bristuff last version.
In the end I succesfully compile zaphfc, but I am not able to use the card
(a lot of problem running zapcfg, a loto of problem starting asterisk
saying about wrong anything (from
2005 Feb 07
2
2 x Fritz!pci card
Hello,
Has anybody installed 2 Fritz pci cards in an asterisk box ?
I can't make them work : each card is working fine when installed alone
(with chan_capi), but I get a kernel freeze when doing 'insmod' with
both cards installed.
I am using Mandrake 10.1 with kernel 2.6, so the hack described at
http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO cannot be used (the
hack requires
2005 Feb 20
1
Mandrake & CAPI
All,
I have been trying to get CAPI4Linux working on my machine and being
frank am failing miserably! I am looking for any help available, I am
real newbie (so please be gentle) and choose to run Mandrake 9.2 as it
appears quite friendly (or so I thought!).
I have been following the guidance found at
http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI for the
AVM card (actually I
2003 Aug 11
1
avm fritz pci
hello,
does anybody know how to setup avm fritz pci card in p2p mode ?
regards marian
--
SUNTEQ s. r. o.
Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic
Tel: +421-46-5430 754 # Fax: +421-46-5439 144
http://www.sunteq.sk/
------------------------------------------------------------
A mind is like a parachute... it only works when it's open.
2004 Dec 27
0
[chan_capi] can't get it compiled
OS: Redhat 9.0
Kernel: 2.4.20-8
Asterisk: latest CVS head
Hi all,
I try to compile the latest chan_capi, but it won't work. I also tried
the patch that is arround there from frank sautter and I have
installed the asterisk header files.
Asterisk is working very good :) and the Fritz AVM pc Card is running.
capiinit:
1 fcpci running fritz-pci A1 3.11-02 0xbc00 5
lsmod:
fcpci
2004 Apr 08
2
Fritz ISDN PCI v2 and CAPI
Hi,
First, here is my config: Kernel version 2.4.25 on a Fedora distro,
Asterisk and a Fritz! Isdn PCI Card (v2). I try to make the CAPI drivers
deal with Asterisk but I can't try to figure out to get of this issue.
As I see, Fritz modules are integrated with the kernel, so I directly
loaded the 'hisax_fcpcipnp' module from it. I install also Capi modules by
downloading archives of the
2004 May 28
3
2 Avm fritz passive card in the same box
Hi, I successfully installed 2 avm card in my asterisk box but I'm unable
to make call. My capi.conf is:
msn=0721111,07211115
incomingmsn=*
controller=1,2
softdtmf=1
context=default
echocancel=yes
callgroup=1
devices=2,2
my capi info :
Contr1: 2 B channels total, 2 B channels free.
Contr2: 2 B channels total, 2 B channels free.
my extensions.conf :
exten =>
2004 Dec 21
1
two avm usb isdn fritz v2.0 cards
I have a problem trying to install two avm fritz cards on one asterisk
machine. I am using fcusb2 driver. 1 card works perfectly.
I tried to recompile driver like it is described on this page but with
no success.
http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO
I think the problem is that i can not find this part of code.
dev = pci_find_device (AVM_VENDOR_ID, AVM_DEVICE_ID, dev);
if
2005 Jan 24
1
AVM Fritz crash
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Not strictly Asterisk related, but I'm trying to get an AVM Fritz! card to
work with Asterisk on a Fedora Core 3 box. I've grabbed the official AVM
Fritz CAPI driver from the AVM website and compiled against the current
kernel. However, as soon as I modprobe it I get:
CAPI Subsystem Rev 1.1.2.8
fcpci: module license 'Proprietary'
2004 Sep 22
2
Problems compiling CAPI
Hello all,
I'm trying to setup a AVM C2 card.
I have read the kernel requirements for this card.
<M> CAPI2.0 support
[*] Verbose reason code reporting (Kernel size +=7K)
[*] CAPI2.0 Middleware support (EXPERIMENTAL)
<M> CAPI2.0 /dev/capi support
[*] CAPI2.0 filesystem support
<M> CAPI2.0 capidrv interface support
My problem is when I make a "make
2004 Jul 15
4
Kernel panic with two Fritz cards
So I've got a PBX running with one Fritz card with the fcpci module and that
works fine, but add another one and... kersplat... Kernel Panic.
It boots fine with two cards, but panics as soon as the first fcpci.ko
module is 'modprobe'd - I don't even get as far as modprobing the second.
Any ideas on what's going on? Should I just back-up to an older version of
the fcpci module
2008 Feb 16
1
Fritz! Card/CAPI Help.
Hi list, i'm keen to move to Asterisk 1.6, so really need to update my
system which is running Mandrake 9.2 although it has been solid for years,
fo Fedora 8.
I have a Fritz! card for ISDN BRI, I have installed the drivers/kernel
drivers from ATrpms
(http://dl.atrpms.net/all/fcpci-03.11.07-14.fc8.i386.rpm and
http://dl.atrpms.net/all/fcpci-kmdl-2.6.23.14-115.fc8PAE-03.11.07-14.fc8.i686.rpm)
2004 Apr 08
0
Réf. : Re: Fritz ISDN PCI v2 and CAPI
If I do that, the modprobe doesn't find any module called fcpci and is
looking for any module called hisax_fcpcipnp as it's the one install for
the isdn fritz card.
# capiinit
modprobe: Can't locate module fcpci
ERROR: failed to load driver fcpci
Maybe, I should reinstall the fritz card drivers itselves? (however, I
don't think so...)
2005 Mar 15
2
fcpci - capi driver for Fritz
I've put my fire proof suit on ready to ask a question ;o)
Redhat 9
Kernel 2.4.20-8
AVM Fritz PCI
Problem 1...
i have followed instructions from:-
http://www.voip-info.org/wiki-Asterisk+AVM+Fritz+CAPI+Driver+Install
http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI
(Plus many many other sites found via google over the last 16 hours)
after modifying the makefile & defs.h,
2006 Dec 06
1
Error compiling Eicon Diva from source
Hello everyone,
I'm having some errors while compiling the source code for an Eicon
Diva BRI card.
I am using Fedora Core 6 with a compiled from source Linux kernel
2.6.19. I have downloaded the Eicon Diva source RPM
(divas4linux_EICON-106.12-1.i386.rpm) and installed it already.
When I go to /usr/lib/eicon/divas/src/ and run ./Build, everything
starts correctly until that part where it has
2010 Mar 01
1
AVM Fritz! mISDN with Kernel 2.6.32 - Any experiences? - Email found in subject
Hi again!
> I have excellent success with the tiny "fcpci" and chan_capi, which is
> also working great with capi4hylafax. See
> net-dialup/fcpci-0.1-r1 in gentoo (should not be difficult to use this
> on other distros, but I have never done so). Do not confuse this with
> the "fritzcapi"!
I managed to install fcpci and it seems to run fine (capiinfo
2003 Nov 19
1
fritz pci / chan_capi / australia setup
Hi * Fans,
I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28:
->
Thanks for your info but I think I have it working at last. Below are
the steps I took which might help others.
1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware
2) Download the Chan_capi from http://www.junghanns.net/asterisk/
3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which
2004 Apr 08
2
Réf. : Re: Fritz ISDN PCI v2 and CAPI
I tried that but it still doesn't work... I think I don't have the correct
approach. Have I to install any ISDN drivers (=modules ?) BEFORE dealing
with CAPI ?
If yes, why shouldn't I use the hisax drivers (which are kernel ones)
instead of fcpci drivers (which doesn't seems to work, by the way...)
And finally, how is it possible to link the two modules together?
As you can see,