similar to: ISDN BRI active adapters with NT mode - any alternatives ?

The demo 1235 extension that Asterisk ships with works fine and the messages are sent to the address I set in voicemail.conf. I guess that means that my configuration is working perfectly so far. But when I set up another extension with a voicemailbox, no mail is sent when a message is left, although I can dial voicemail and listen to the message just fine which I guess rules out voicemailbox

Hello, I need to connect one diva server 4bri to a portuguese BRI interface. The operator (PT) said that this bri is in point-to-multipoint mode (S0). Previously one PBX has connected to that interface. The asterisk and diva drivers are working ok but i cannot communicate to outside via this bri. Xlite gives me the message: "call failed: declined". Anyone have experience with this

Hi (Armin?) ! Today I had a problem with Diva Server 4BRI-8M 2.0. Asterisk 1.2.12.1 chan_capi-cm-0.6.5 divas4linux-melware-3.0.f-106.622-1 Asterisk could not receive and make calls on the BRI ports, although the ports looked fine within Asterisk. I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line activity. This time there was no activity (cryptic log

Hi there I am in the UK.. and am running latest asterisk on FC1 (2.4 kernel). I would like to know what the best option is for a 4 port BRI card. I notice Digium don't provide one.. I have heard the Junghanns do one...but are there others ?? Is the Junghanns card reliable/stable with good sound quality ?? I notice it is very expensive in a per port comparison with the Digium cards.... hence

Is the Sipura 3000 the only way to interface a remote pstn line and connect incoming calls to Asterisk? I have a location connected by network that has a phone line, when the room is occupied I want the line ti ring there as normal, but when the employee is travelling I want the line to be conencted to a ATA that then feeds it as an incoming pstn line to the pbx located at my office so it can

We recently had a customer install that went horribly wrong. Serious echo (pots lines into a cac cb) that, although * did a good job getting rid of alot of it, could not get rid of it all. We tried everything, every canceller, gain setting, etc... combination possible to no avail. Both the vegastream and mediatrix boxes also could not get rid of all of the echo. So, on an off chance, we

Hi All, I'd really like to see a show of hands with regard to people's experience with FXO interfaces. I own a few X100p cards and have had nothing but problems with them. I also took part in Sipura's beta program, for the SPA-3000. While it can be an improvement over the X100p, it presently has echo problems that make it unusable. Sipura has not acknowledged the problem ( at least

Hello, I try to use Asterisk with an Eicon-card called "DIVA Server 4BRI-8M PCI" but I don?t get it to work. I?m running on RH8.0. The Eicon-card supports isdn4linux. In the modem.conf file i have put following: ----------- [interfaces] ; By default, incoming calls should come in on the "remote" context context=remote ; Modem Drivers to load driver=i4l ; Type of dialing

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

I want to test asterisk with its DID functions on a smaller scale without the expense of a PRI. I am in the US, and want the most reliable/stable, and feature rich solution that I can have. What ISDN card would be reccommended? My clec switch operator says he can/will send DID info to my BRI's if I wish. Can Asterisk, or one of its addons support this? What BRI solution would be

Hi everybody. I'm trying to setting up a V4 BRI EICON card on ASTERISK 1.0.7 My linux is a debian. It was working during a few days an suddenly (after a lot of reboot) I've got this error message that seems to be very popular but I couldn't find any answer on the net : ==============================================. Asterisk Dynamic Loader Starting: == Parsing

We are looking to lose the TDM400P in favor of an ISDN-BRI solution. This should get rid of static on the line (at least any static generated by our half of the circuit), right? I am a total virgin to ISDN. I understand that we need two BRI circuits to provide four voice channels, and that the hardware to speak to the BRI circuits can be passive or active, with the active type being much more

Hi (Armin)! Does someone knows how to identify the type of the card? The delivery note says it is a V-4BRI-8M, whereas lspci reports a 4BRI-8M. What is it really? Are there any Eicon tools to identify the card type? thanks klaus 0000:0a:03.0 Network controller: Eicon Networks Corporation Diva Server 4BRI-8M Rev 2 (rev 01) Subsystem: Eicon Networks Corporation Diva Server 4BRI-8M Rev

Heya Mark (and others), Here's an update on my adventures while trying to debug the Zaptel-related panics, as discussed on this list a while back. While debugging the problem, I completely swapped the machine for an entirely different model (Supermicro dual Xeon 2.4GHz with 2Gb of RAM), put the cards in, recompiled * + Zaptel and administered my stress-test. The machine stayed up in excess

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n:

I am trying to configure a VegaStream 50 FXO to work with asterisk. The problem that I am having is that the VegaStream does not support incoming registration from asterisk. VegaStream only allows outbound registration. My question is does asterisk allow incoming registration from an FXO? If yes how? Or better yet, has anybody been able to make the VegaStream FXO work with asterisk? According

Hello Everyone, I am once again wondering about EICON. I have had no success with the Diva Pro or Diva Pro PCI, so my question is, does anyone use an Eicon Server BRI card on Asterisk? Or would I be better off trying to get a split PRI? Regards, Greg

Hi Guys! I got a Diva passive ISDN card and I can't get it work with asterisk 1.4, It is supported in the kernel as an isdn4linux device but I can't find "Modem" channel type when i type in: core show channeltypes. I'm guessing it is removed in asterisk 1.4. Tried with capi interface but it does not work :( Anybody got some idea how can i make it work or got a link to a

Dear all, I'm planning to buying Eicon Diva Server V-BRI for my asterisk server and run with chan_capi. Is anybody using that card ? Would appreciate any feedback. Bartosz