similar to: The old versus new TDM400P board

Since the irc channel wasn't any help, I will try posting my problem here. I have two TDM400Ps less than a week old in a PC. All of the FXS ports work fine, and all of the FXO ports worked fine up until thisafternoon. If I try to dial in, I get a busy signal, if I try to dial out, all I hear is a very scratchy, very crackly dialtone. If I swap the first FXO module with the second on the card,

Hello list... 1) Is there an IAX softphone that supports any kind of voicemail indicator? 2) I have 2 TDM400Ps installed in a system. I need the audio on the analog phone (FXS modules) to be amplified somewhere between 10 and 15db so I set rxgain and txgain to 15 for the FXO interfaces and FXS interfaces. When a call comes in on the FXO at this setting, the call sometimes has about 20 seconds of

Hello folks, I'm very interested in the Digium/Asterisk combination but need some clarification. I would like to setup a SOHO for business and home use. Scenario One: I have one analog line, 4 analog telephones. Do I need a TDM400P + 4 FXS modules (Green) + X100P? Scenario Two: 2 analog lines, 1 selective ring number for fax, 8 analog phones. Is this what I need? 2 TDM400Ps and 8 FXS

Hi all, Theoretically, I know it's possible, but is any using multiple tdm400ps (fxo) in single * box? In a production environment? Any gotchas aside form irq sharing? Thanks Ryan

Not to sound like a broken record but...... Is there any word on the availability of the FXO cards for the TDM400P? I have an application that would benefit. If it has been dropped please let me know. Thanks Gene Kochanowsky

Hello. I've seen several posts talking about line quality using Digium cards that are sharing IRQs or on machines where X is running but after trying all of those fixes I am still having a problem with line static on outoing calls. BTW, calls that are from one extension to another extension have no static, however, they have occasional clicks and pops. At any rate, I was wondering if

I recently purchased a Asterisk Developer's Kit (TDM) and now have it outfitted with 2 FXO modules and 2 FXS modules. I'm not using the X100P modem card that came with the kit. I'm having problems with dialing out on my POTS line. Successful dial out is intermittent. About 50% of the time the call goes through. The other 50% it is dialing the wrong number. ( I can hear the error

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

I can't seem to make the fax detection work. Here's an excerpt from zapata.conf: signalling=fxs_ks group=0 context => guestaccess channel => 47-48 and from extensions.conf: [guestaccess] include => incomingmain [incomingmain] exten => s,1,Dial,Zap/1&Zap/9&Zap/10&Zap/11|24 exten => s,2,Voicemail,u7000 exten =>

Is there any way to receive and send faxes using a T100 card? If so how is it done? Gene Kochanowsky Solution Sciences, Inc.

My Cisco 7905 can't register with Asterisk (1.0.7-BRIstuffed-0.2.0-RC7k on Debian stable). It could, however, register with another installation of Asterisk and the settings on the phone (apart from the SIP proxy address) haven't changed since then. On the new Asterisk box my sip.conf contains this: [jeremy] type=friend regexten=801 allow=g729 host=dynamic secret=PASSWORD nat=yes

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

List members, Is it possible to record outbound analog calls using an X100P? I was asked if I knew how to record all calls for a shop with 4 analog phones transparently to the end users. I thought Asterisk was a good fit for this and I envisioned using either Digium TDM400Ps or Sangoma A200s with 4 FXO and 4 FXS modules. The FXO modules would be connected to the existing PBX and the FXS

asterisk-dev-bounces@lists.digium.com wrote: > I have a DSP based system that is working on a four port FXS system > using a 200MHz arm processor. Well.. since we are talking about this topic I owe you guys notes of my experience with SC1100 CPU used by various boards (www.soekris.com , www.pcengines.ch etc.). We made a Linux distro and compacted it into 32MB flash. Installed asterisk and

Hi, > Aha... Hadn't noticed that stringsAsFactors only works via as.is in read.table. > > Yes, the doc should probably be fixed. The code probably not Agreed. Is someone on-list authorized and willing to make the documentation change? I suppose I could learn what it takes to be a "player", but for such a trivial fix, it probably is overkill. Dissenting opinions?

Hi all, haven't seen many posts about asterisk in Singapore... Getting a server going there and was wondering if TDM400Ps will be fine in FCC mode, and if there are indications / cadence values that I should be putting on there as in other international locations. Seen an unsettling post on voip-info about Singapore issues with Call Polarity/Hangup Detection -- crossing my fingers I

I hooked up a SPA-1001 with asterisk yesterday and all works well except the phone doesn't ring. The phone I'm using has a LCD display so I can see the call come in. (with caller id info) I can answer and complete the call but it's just not ringing. The phone rings if pluged into a POTS line so it's not the phone that's the problem. I've used the SPA-1001's web

On Thu, Feb 18, 2016 at 6:03 PM, Cook, Malcolm <MEC at stowers.org> wrote: > Hi Peter, > > Sorry if I was not clear. Perhaps an example will make my point: > >> data(iris) >> class(iris$Species) > [1] "factor" >> write.table(iris,'data/myiris.tab') >> data(myiris) >> class(myiris$Species) > [1] "factor" >>

samba@samba.org schrieb: > SAMBA Digest 1928 > > For information on unsubscribing see http://samba.org/listproc/ > Topics covered in this issue include: > > 1) Re: NT Logon Authentication > by Gerald Carter <cartegw@Eng.Auburn.EDU> > 2) Samba-> No [.] and [..] directories > by Kai Schaeffer