similar to: ISDN problems (Take 2)

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

G'day, New to Asterisk alert! I have a Netjet card running on linux 2.4.27 kernel using the HiSax module, and trying to use it for incoming/outgoing calls from *. I've tried playing with modem.conf and extensions.conf every which way I can think of, using samples and whatever I can find off the net, and I get the same message everytime I try to dial in. The complete message is:

Hello List! I finally got asterisk with capi working, and its already answering my call as well! :) Now i would like to call a number from my shoft phone (kphone). This is my extentions.conf: --- [general] static=yes writeprotect=no [globals] CONSOLE=Console/dsp ; Console interface for demo IAXINFO=guest ; IAXtel username/password

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm having some problems using the asterisk modem driver with an ISDN4Linux card (AVM Fritz). (I realise that it's better to use CAPI, but unfortunately this card doesn't have any CAPI drivers). Every so often the ISDN just stops working (it neither dials out nor accepts incoming calls). Trying to dial out just logs: --

Hi, I have a problem that I just can't figure out how to solve. I start *, dial it using a ISDN phone over PSTM, to a Hisax card installed in * I get the demo-greeting, listen for a few seconds and hang up. I dial it again, but this time the first second is sound from where the previous call ended, then the greeting starts as it should. Right now I have removed all codecs but codec_gsm.so

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Hello all, I currently have an Eicon Diva Client isdn card using i4l. Outbound dtmf doesn't work (and never has), but there has been an annoying problem with false dtmf detection in calls (that could be triggered easily by blowing into the receiver on the remote end). I looked through the list and found two patches that need to be applied - 1 to isdn_tty.c in the kernel, and another to

Hello, I try to use Asterisk with an Eicon-card called "DIVA Server 4BRI-8M PCI" but I don?t get it to work. I?m running on RH8.0. The Eicon-card supports isdn4linux. In the modem.conf file i have put following: ----------- [interfaces] ; By default, incoming calls should come in on the "remote" context context=remote ; Modem Drivers to load driver=i4l ; Type of dialing

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

I have installed a Billion ISDN card in my Asterisk. Calls between sip and isdn work. The i4l channel has MSN=26. I also put incomingmsn=26,27 in modem.conf. extensions.con: [incoming-isdn] exten => s,1,Dial(SIP/701,20,Ttr) ;will make my extension 701 ring, while exten => 26,1,Dial(SIP/701,20,Ttr) ;will cause an error message in the Cli interface: WARNING[196621]: pbx.c:1814

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

Hello, I acquired a Diva Server 4BRI for an AsteriskPBX system and installed a 2.4.20 kernel modified with the latest eicon capi2.0 support from www.melware.net. Capi support seems to work fine: Asterisk+chan_capi answers the calls. However if I try to use my old isdnutils apps by loading a i4l compatibility layer then I have the following problems: - if I use the diva2i4l module and start the

Can anyone work out why my callerid doesn't work on my isdn4Linux with asterisk (or without asterisk for that matter)... This used to work fine, and I am quite confident that the telco is sending callerid information (because they always do on all ISDN lines standard, only extra cost on POTS lines). This is the information from dmesg, whether asterisk is running or not: isdn_net: Incoming

Currently we have problems with our asterisk server connect with an Eicon Diva 4BRI Card to a PBX. Asterisk is running in version 1.0.0 on RedHat Enterprise Linux 3AS with kernel 2.4.21-4.EL. The Diva server is running in version 7.5 Can someone help us in reolving the errors with incoming calls? When we try to call to an extension we get these messages in the CLI: -- creating pipe for

I'm trying to use an hfc based pci card with asterisk but every call fails falling in the congestion extension. exten => _0.,1,Dial(${TRUNK}:${EXTEN:${TRUNKMSD}}||tr) exten => _0.,2,Congestion Looking in the syslog i can see: isdn: HiSax,ch0 cause: E001B it seems that this is a terrible error when arrives... hard to tell what is the cause. Also terrible is finding a lot of material