similar to: E1 PRI's in Australia

Hi, I am currently trying to find a replacement for a dinosaur PBX and want to replace it with a VoIP solution. We have just moved our lines over to an Optus Multiline from a Telstra ISDN Onramp 30 service with 100 lines. My question for you good people is what sort of hardware do I need to interface Asterix into the Optus Multiline? The Optus service is terminated in my office to a SHDSL

Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not

I am having problems getting incoming caller id to work on a Telstra Onramp 10. I have changed "/DEFAULT_CIDRINGS 2"/ Is there something i'm missing ? My Cisco 7960 just shows "asterisk" Thanks, Nathan [zapata.conf] context=incoming usecallingpres=yes relaxdtmf=no rxgain=0.0 txgain=0.0 busydetect=no pridialplan=local usecallerid=yes callerid=asreceived

We are not having any luck with the E100p card here in Australia, it will work with a crossover cable to another device but will not talk to our Telco Telstra who probably have a weird implementation of an E1. Any suggestions on a replacement? Regards Mark McKibbin DCS Internet 64 Queen St Warragul Victoria 3820 Australia www.dcsi.net.au mark@team.dcsi.net.au Ph. 1300 665575 Fx. 1300 556595

Hello list, I have an X100P clone card, and I've been trying to get it to receive Telstra Caller-ID without any luck. Hence these two questions:- 1) Will a genuine X100P work? 2) If so, where can I get one in Australia? Cheers, Jon

Hi All, This isn't really a question, but it's an issue I experienced that was driving me crazy for a few days, so I thought it might be good for the archives. Basically what was happening was everytime a particular customer called (long distance), the line would disconnect immediately after answering. I thought it might have been the phone, so I swapped the phone with another - still

> > That would be called a milliwatt generator. It likely exists in their > central office, but its typically used by their technicians to ensure > new installations meet specs and sometimes in troubleshooting. Call your > telco repair number and see if they will give you the telephone number > for it. I'll try that. 1st line technical support at Telstra are not known for

I'm planning a system, just need to know if it works with Telstra's network. Cheers, Clint Sydney, Australia

I have an x100p which suffers from echo (no surprise there apparantly :), and a few of the things I've read about tuning out echo say the first thing to get right is the tx and rx gain, and for that you need a few different types of test lines from the telco (Telstra, Optus, whatever). Does anyone have any numbers in Australia for such lines? I think they just need to send out a tone of a

Telstra (Australian Telco) has recently introduced a feature to allow the sending of SMS direct to fixed analogue lines, with an appropriate handset. As best as I can figure out, this appears to use CID type signalling, or at least on a line that otherwise has no CID on it, CID is sent, but with a standard modem I can only receive the date, time, and phone number (eg normal CID info). After that

Hello, Rather than rely on a set of IF statements (as there could be many - please see below)), could the following be done in a different/better way? InternalMean <- mean(data1[,3]) if (InternalMean == 0) Intresult = 1 if (InternalMean > 0 & InternalMean < 1) Intresult = .95 if (InternalMean >= 1 & InternalMean < 2) Intresult = .85 if (InternalMean >= 2

We just installed a box into a Melbourne site with a Sangoma A101U, it is running the latest Wanpipe drivers and has Asterisk on it that someone had compiled manually from source. This initially worked fine but for the sake of consitancy we removed the existing asterisk and used emerge to install it. During this time the box was off of the e1 for about 8 hours and when it was brought back

Do any of the Australian Telstra users have some working tx/rx gain settins for the Sangoma cards on Telstra that I can try, echo is acceptable but not perfect using 0/0. I will also post them onto the wiki. Regards, Andy

Hello, We have an Asterisk 1.0.9 machine with a Sangoma A101 card fitted, it is connected to a Telstra OnRamp E1 in Melbourne, Australia. The problem we are experiencing is extreme echo and clicking noises. These are only audible to the calling party, e.g. the person calling in from the PSTN to Asterisk via the E1, the person on the SIP handset cannot hear any echo or clicking, only the

Hey all, I''m back. Some of you are probably thinking that is the longest weeks vacation on record. Well, I''d like to take this opportunity to apologise for my absence and offer a brief explanation. When I got back to Australia I naturally went home to visit my parents, only to find that they have been hit really hard by the drought. They didn''t really tell me just how

I've installed a TDM400. Having a go with AMP. I would like incoming calls to be put throuhg to an extension (at my desk) and a mobile (cell phone) at the same time. Whichever picks up, gets the call.. This should be possible with AMP (call groups, 200|201|0*0408xxxxxx), but it didn't work, so I have created a custom-incoming in extensions-custom.conf What is happening is, The extension

Thanks Mike. My data has longitude and latitude coords and I used distAB {clim.pact} then mst {ape} to calculate my minimum spanning tree. The nodes are telecoms sites from all over Australia. My goal is to determine the minimum cost of linking them via cabling, and I'm starting by calculating the distance "as the crow flies", but will probably eventually need to calculate the

I've setup a sup server on sup.physics.usyd.edu.au for use by people in Australia. It has current, ports and stable (except des, etc). The max number of connections is currently set to 10, and the daily sup updates begin at 3am local time (if a different time would be better, let me know). This machine is located in Sydney, with good connectivity to the NSW AARNet/TIS gateway. If the plans

Hi, now that these cards have approval in Australia, has anyone had any luck in connecting them to a Telstra Onramp 10 service? Are these configured as a PRI, bchan=1-10, dchan=16 in zaptel.conf and switchtype=euroisdn in zapata.conf? Better yet anyone have any of the above .conf files they could share? Is an onramp 10 what is referred to as a 'channel bank'? Craig

RH Linux 9 on AMD k6-2 500 Using HP deskjet 930c on USB Samba version: 2.2.7a cups version: 1.1.18 Hello - I have had a good look on this newsgroup - and what I've picked up I think is allowing me to ask these questions more intelligently. I've also had a good look at the CUPS documentation aswell as the Samba documentation. 1. Am I correct is assuming that CUPS only likes postscript,