similar to: DTMF Tones During Call

Hi, I am using a Netjet-s ISDN Card, and am having some trouble dialling out (Incoming Works Fine). TRUNK=Modem/ttyI0 exten => _90XXXXXXXXX,1,Dial(${TRUNK}/${EXTEN:1}||Ttm) exten => _90XXXXXXXXX,2,Congestion I get the following when diallingout: -- Starting simple switch on 'Zap/2-1' -- Executing Dial("Zap/2-1", "Modem/ttyI0/04XXXXXXXX||Ttm") in new

I found this old post using a Google search for DTMF tones heard during an Asterisk call. The calling party does not hear them, only the called party. We are experiencing this sporadic DTMF "beep" followed by a momentary silence on a random number of our calls. This happens on trunk to SIP and SIP to SIP calls, so it's not PRI related. Since this thread is dated 2003, and the

Hello, I'm having trouble working out how to send DTMF tones to an external IVR. My system has an analog phone connected to a TDM400P card, a SIP software phone (Zultys LIPZ4) and is connected to a BRI in Australia with a NETjet-S card. I'm using ISDN4Linux and a 2.4.25 kernel patched with the ISDN audio patch from Traverse (which allows the card to do voice). DTMF works fine between

Trying to get a myth backend running in fedora core 6 and xend 3.0.3 but having some issues with the DVB ATSC card, I have removed it from Dom0 and presented it to my vm, but I am unable to scan for channels...this is what lspci looks like for the card: lspci -v 00:00.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev 02) Subsystem:

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

I'll try again using my subscribed address... Apologies to the moderators... --- Hi All, I've successfully got SIP and IAX2 working on Asterisk using X-Lite as a SIP phone and talking to a remote Asterisk over IAX2 using G729. I'm now trying to get an ISDN BRI connection working. I have a Traverse NetJet card (http://www.traverse.com.au/) which I currently have working with

Hello all, I would like to document some things I am doing with asterisk, but would prefer to do this from a web interface. I am unfamiliar with any software that allows you to create online documentation from a web interface. Ideally I will be able to create documentation online from a browser, which then when saved, is immediately ready to be read online. Perhaps I can setup different authors

Hello all, I was wondering if anybody knows where one might obtain a PCI ISDN card supporting a single BRI for use with Asterisk in Australia (and using something like chan_capi). Because of the Isdn4Linux DTMF issue, I don't want one of those cards. I've already spent too much time messing about with my current card. I'm after something like the AVM Fritz! cards. I found one place

Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Asterisk - 1.8.4.1 Dahdi-linux - 2.4.1.2 Dahdi-tools - 2.4.1 Kernel: 2.6.37.6 Kernel BKL: enabled I am upgrading Asterisk on this box. It has an OpenVox A400P PCI analog card with 1 FXO and 1FXS module. This server has been running just fine for two years with Asterisk 1.6.1.0 I've just upgraded all the OS and installed Asterisk 1.8.4.1. On trying to configure the A400P I get: # modprobe

I'm trying to use a Teles (netjet) ISDN BRI card with asterisk 1.2.9.1 Anyone was able to use this card with asterisk? I couldn't find much information about it. Any help?

I am one of the few people left in the US with a ISDN connection to the internet. (Internet cable has been promised "Real Soon Now" for a couple years). Worse, my home network runs on a decrepit Cisco 2500 series router, and is double-natted via a firewall, which is why I currently use iax to call anywhere. I have been making ever-increasing use of my asterisk PBX, and I'm ready

Does Asterisk support Radius accounting?.... -----Mensaje original----- De: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] En nombre de asterisk-users-request@lists.digium.com Enviado el: Lunes, 17 de Noviembre de 2003 12:08 p.m. Para: asterisk-users@lists.digium.com Asunto: Asterisk-Users digest, Vol 1 #1912 - 11 msgs Send Asterisk-Users mailing list

Hi, Last weekend I was planning to buy a physical PBX system, but instead I have been blown away by the fact that VoIP really works, that Asterisk is so easy to set up and use... and free! We're in Australia, so as I understand it, we aren't allowed to use the Zaptel cards. We need to set up our system to route incoming 56K data calls to the PPP daemon on our Linux box or to our

I see many posts about using ISDN cards and modem cards. Does this mean I can use a regular modem (that supports voice) as an FXS, or FXO ? If so, can you provide an example. It might be the easiest way to test Asterisk's collaboration with the PSTN (or analog phones) and provide proof of concept to non-believers. Thanks. Shoval -------------- next part

If I want to send outgoing DTMF over a BRI interface, can I do it with 'isdn4linux' or must I use the 'capi' library? -- . . ___. .__ Posix Systems - Sth Africa /| /| / /__ mje@posix.co.za - Mark J Elkins, Cisco CCIE / |/ |ARK \_/ /__ LKINS Tel: +27 12 807 0590 Cell: +27 82 601 0496 -------------- next part -------------- A non-text attachment was