similar to: Hardware question

Could someone explain to a non-US dummy the following phrases I have seen on the list. "I can provide you with tier 1 termination 6/6. I can blend or NPANXX breakout." "We provide US48 termination, blended rate for 1 MOU and above is .008 with 6/6." What is 6/6? What is US48? What is blended? What is MOU? What is NPANXX breakout? -------------- next part --------------

Greetings list, I've been asked to provide a system for 200 extensions, most of which will be existing analogue POTS handsets, not IP handsets. I've not really had any experience with large channel banks in the past (since most of our deployments are strictly IP-only to the desk), so I'm at a loss as to which ones are worth looking at. If anyone's had experience using channel

Hi, Is this card the same as the T410P, after all, it's made by Digium. There's one prior reference on the mailint list[1] but it didn't answer the question. There was also an SS7 status report[2] last June but it's doesn't seem to have lead anywhere either. There was post saying an SS7 release was immenent last September[3], but then silence. Any info anyone would like to

Hi, I found E400P quad PRI card quite cheap (749USD): http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754 in comparison to te410p (approx 1500 USD ) http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P Now newer generation with HW echo canceling emerged (te411p). I'm not sure in what things those two cards

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Hi, Digium's E400P has RJ45 conector and my E1 link has BNC concetor. Could someone tell me the cable pinouts to make this conection? thanks Eduardo

I have 7965 and am trying to convert the firmware to SIP (SIP45.8-3-4SR1S). Does anyone have a valid XMLDefault.cnf.xml they could share? I have tried the version at voip-info<info.org/wiki/view/Asterisk+phone+cisco+79x1+xml+configuration+files+for+SIP&view_comment_id=14768#Troubleshooting>for the 7941/7961 but unfortunately /var/log/messages shows in.tftp stops sending after

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

hi All, quit new to asterisk, can anybody tell me whether Wildcard E400P and Wildcard E100P support R2 CAS protocol. if they do, what is the value, i should set to 'signalling' parameter in the zapata.conf file? Surajee -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi everybody. We have a problem with the configuration of the card, the cards work and we receive incoming calls but asterisk don't receive dnid. We have 5 servers with 1 E400P with the same problem and the telco told us that we need to configure the card to request it, how we can do this? Can you help me to solve the problem. Best regards, Carlos Fernández Puente carlos.fernandez@alisys.net

We've changed E1 providers and I'm trying to reconfigure an E400P to make it work with the new lines. They're supposedly "standard" EuroISDN lines (in the UK). I'm initially just trying to get a single line up. I have the following in /etc/zaptel.conf: span=1,0,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 loadzone=uk defaultzone=uk The LED on the back

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Hello all, I have some questions about the libpri and zap lib. I've sent mail to Mark for help. Also I wonder whether anyone else would be interested and helpful in them. I'm going to migrate a program to Wildcard E400P card. Our original program is based on C API similar to the functions provided in libpri.h and zap.h, so I want to use the E400P card in the following way: 1. install and

A brandly new E400P 128 channel PRI, you can find more information on the Digium's site. The card was not used before, I sell it cause our company just don't need, we use Cisco AS5300. I can offer you the PCI PRI at $940 if bought in the next 2 days, I can send it to you via FedEx or DHL express. Please email me for more details! Regards, Kalin ----------------------------- IPPN Networks

Hi! I have the chance to play with a couple of E400P cards, each installed in a IBM e330 XSeries servers (2 x 1GHz P-III CPU 2 Gb RAM, 36Gb SCSI HDD with RH8.0 2.4.18-smp kernel), and I'm trying to test/benchmark this e330/E400P combo generating calls thru /var/spool/asterisk/outgoing One e400P if doing the carrier work making calls and the other just receives the calls: Server#1

Hi, I came back from a quiet weekend today and found my E400P box to have gone astray. Asterisk is loaded from inittab, and started crashing and reloading a couple of thousands of times, each time notifying my monitoring service :-P I remember there would be issues on old cvs stuff since the crash at digium so I made a clean checkout just now. Here is what happens when I load manually:

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help