similar to: FXO mode

I've just down loaded Xten Lite and it is now build 1079. It now finds the NAT firewall type and has loads more to configure. But it doesn't work on my poor W95 tablet PC. -- Dave Cotton Directeur Linux Autrement 193 rue Marcel Cerdan 84270 Vedene 04 90 23 30 81 "Internet Sheriff Technology" revendeur en France <http://www.linuxautrement.com> IAX 17004902330

Zaptel seems to compile fine until I enter xpp/utils and make there. I get: xpp/utils # make cc -o print_modes -g -Wall print_modes.c print_modes.c: In function `main': print_modes.c:9: error: `fxo_modes' undeclared (first use in this function) print_modes.c:9: error: (Each undeclared identifier is reported only once print_modes.c:9: error: for each function it appears in.)

Hi, I've been trying to get my zaptel x100p cards working for the past week now. this is what I've done: installed asterisk: make clean make linux 26 (for fedora core 2) make install installed zaptel: make clean make make install did a modprobe zaptel, and wcfxo got this in /var/log/messages: PCI: found IRQ 11 for device 0000:00:0f.0 wcfxo: daa mode is 'FCC' found a

Hi, in response to a previous posting regarding getting the x100p to work, I was told to run "zap show channels," but when i do i get "no such command 'zap'" There was a previous posting on this, but the guy never posted the solution. thanks, Imran

I am finding that I have to increase the txgain in zapata.conf to 8 when my X101P is connected to my BT phone line, otherwise people can hardly hear me. This then gives echo issues. Do other people have the same problem on BT lines. I was wondering if I should give BT a call and get them to increase the gain on the line. Strange though as the rxgain is OK and I don't have this problem with

Using CVS update from 11:00 CET today * crashes at this point. == Parsing '/var/spool/asterisk/voicemail/default/2201/INBOX/msg0000.txt': == Parsing '/var/spool/asterisk/voicemail/default/2201/INBOX/msg0000.txt': Found Sheriff*CLI> Disconnected from Asterisk server -- Dave Cotton <dcotton@linuxautrement.com>

Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp kernel. I've two x100p cards connected, only one card is reconigzed by asterisk. 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) 02:03.0 Communication controller: Tiger Jet

I don't think I've ever seen so many commits to the CVS, I'm not complaining. To save lots of checkout/test cycles can a message be posted when the current surge is over? -- Dave Cotton Directeur Linux Autrement 193 rue Marcel Cerdan 84270 Vedene 04 90 23 30 81 <http://www.linuxautrement.com> IAX 17004902330 FWD 42651

Hi I'm a little lost on how to set things up with the two FXO cards I have: I want card #2 to dial a number when a call comes in on card #1. Using the following configuration, card #1 picks up the line and remains silent, instead of dialing out through card #2. Anybody knows what's wrong? --------- /etc/zaptel.conf --------- # Zaptel Configuration File # fxsks=1,2 loadzone=fr

Hi All, I have followed below steps to enable echo cancellation. # cd /usr/src # wget http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.28.tar.bz2 # tar xjf linux-2.6.28.tar.bz2 # tar zxvf dahdi-linux-2.1.0.4.tar.gz # ln -s /usr/src/dahdi-linux-2.1.0.4 /usr/src/dahdi # mkdir /usr/src/dahdi/drivers/staging # cp -fR /usr/src/linux-2.6.28/drivers/staging/echo /usr/src/dahdi/drivers/staging # sed -i

Hi, We are currently testing Asterisk with Wildcard 100XP and serveral Cisco ATA Box. Everything works great except that the card does not detect the hangup signal. We are using a standard Belgian PSTN line. I have not found anything about a be zone (only us, fr, de, nl, ...). Does someone experience the same problem? Do I need to create a new zone be (and how to do that)? Another small

Hi, I installed a 1-port FXO on my Ubuntu 8.4. I was earlier only hearing a fast clicking sound and now I am not hearing any dial-tone. The FXO card has 2 slots: [phone | line ]. I hve connected the wall-phone-input to the "line" slot and "phone" to my home-phone. I do not hear any dial-tone on my home-phone. Asterisk seems to recognize my hardware....here are the relevant

When I set up my Asterisk box at home I didn't want to have to dial 9 to dial off premises, so I gave all my local phones three digit extensions with this format: 1[1,0]*. My thought is that there are no area codes that start with 0 or 1, so if I use those numbers, I can create 20 local extensions that can be dialed with 3 digits, and not have to use a timeout when dialing long distance. If

Hello All, I am getting a set of errors when I boot Asterisk that I have not been able to solve. What is causing these error(s)? Asterisk boot output: ============== Asterisk CVS-04/10/04-21:44:51, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= [

Hi All; If I need to set the opermode to King Saudi Arabia, what the name I have to use? For example, to set it for kuwait then I use opermode=KUWAIT. So what will be for Saudi Arabia? Any advise? Regards Bilal

Hi all, After reading great things about the OSLEC Echo Canceller (http://www.rowetel.com/ucasterisk/oslec) and seeing the reactions of people who have tried it on a recent Trixbox thread (http://www.trixbox.org/forums/trixbox-forums/open-discussion/need-people-echo-problems), it sounds like it is the "bees knees" for sorting out echo problems with cards like the x100p. Has anyone

I have just got my X100p card and am trying to install it. I have built and installed the zaptel drivers without any apparent errors and I am now trying to get them working. I have the following in config files In /etc/zaptel.conf fxsks=1 In /etc/asterisk/zapata.conf signalling=fxs_ks context=default channel => 1 Now when I try ti modprobe the drivers this is what happens: Command:

I lost my internet connection today for a short time. During that time 1.2.12.1 stopped talking to my phones. Asterisk was still working as I got 2 voicemails. I have TDM analog cards for incoming calls. Anyway my cisco phones had X's (lost registration) and my uniden phones said "Registration error". Why would phones loose registration to asterisk when the internet connection

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

Owias, The 537 is, for the most part, a drop-in replacement for the Digium card. Please search the archive and the Wiki, as there have recently been several discussions about this exact subject. To my knowledge that is about the only modem that works, but keep in mind it is _not_ supported. That being said, follow the instructions on Digium's site for installing the X100P and you should be