similar to: "immediate=yes or Compleate recieved" with intcoming calls with new CVS

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

Hello, Configuration: Asterisk CVS HEAD 20050730 on RH EL3+ DIGIUM TE110P PRI card + euroISDN E1 I am trying to sort out the problem: 1. Provider's switch sends "SETUP"; 2. Asterisk receives "SETUP", rings allocated extension but does not send "Setup acknowledge" (or any other messages) to switch; 3. After 4 seconds of waiting of *'s response switch sends

Hey all, I am running a Asterisk 1.2.9.1 with Sangoma A101 card, newest firmware, configured with a help from Sangoma Tech Support, running fine. It is connected to a PRI circuit split from Cisco MC 3810, which in turn is connected to a Converged T from CTC Communications. While Asterisk works fine and I can call in/out on my BV account, I am only able to dial in through CTC. I have spent

hello everyone, I have a trixbox server with an E1 card(not digium).It connects to an AVAYA pbx use E1. It works fine.But when i change the E1 card to digium TE220B,there is a problem. When sip extension A(on trixbox) call PSTN extension B(on avaya),A must wait longtime before B start to ring.From the log I find there are two times call. I don't know why the first request be rejected

Hello all, the scenario: Carrier ----S2M------ * -----S2M------Siemens | | SIP Clients and many other features With much help from the list, the PRI links are without alarms and inbound calls are working fine (from both: Carrier and Siemens). But I am not able to dial wether outbound nor to the Siemens PBX. I allways get the message: == Everyone is busy

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

Hi, When we make an outgoing call on ISDN (zaphfc) with overlap dialing we get immidiate hangup after answer. But when we place a full number before dialing everything is ok. Any help appriciated!! Thanks here is info with debug: == Primary D-Channel on span 1 up -- Executing Dial("SIP/200-164c", "zap/g1/|100|tc") in new stack -- Making new call for cr 192 --

Hi, When have a incoming call from E1 to a extension FXS, and this extension is busy, the incoming call recive ring tone, and it is wrong. What can I do? Thanks in advance Pedro Here is the trace: asterisk-1*CLI> < Protocol Discriminator: Q.931 (8) len=41 < Call Ref: len= 2 (reference 66/0x42) (Originator) < Message type: SETUP (5) < Sending Complete (len= 4) < Bearer

Hi, ? I'm trying to figure out what the issue is splicing Asterisk between our Telewest PRI and a GDK-186 with a PRI card. ? We're using the Digium TE405P ? Our telco provider is Telewest, and Telco directly into switch is fine. ? When I splice Asterisk in, I can make and receive calls from Asterisk extensions, I can make outbound calls from the GDK, but inbound calls do not seem to pass

OK I am going to do it again. Global Crossing is now sending ANI but it is not in the format I expected. Any one know of a way to get this data into two seperate variables? The first number is ANI and the second is DNIS so it is "*tendigits*tendigits* on one line like below. < Called Number (len=26) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan

I am trying to put a call on a E1 ISDN : The configuration are simple: zapata.conf : [channels] context=inbound switchtype=euroisdn signalling=pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes ;echocancel=no echocancelwhenbridged=yes rxgain=0.0 txgain=0.0 ;immediate=yes immediate=no callerid => asreceived amaflags

Hey all. We have a DS3 circuit with GBLX split off into 7 systems with a 4 port sangoma card (A104D) in the first 2 systems, and digium T410P cards in the other 5. GBLX numbers their spans from 0 to 3 instead of 1-4 and we have a NFAS configuration with the d-channel on chan 96. All of our systems are running 1.0.7 for stability reasons (and no good time for maintaince, the entire platform

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (just one!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR some time

When trying to make outbound calls I am getting the Warning: File app_dial.c line 313 (wait_for_answer) Unable to forward voice. When making the call it attempts to dial (pounds are actually numbers but replaced to not show numbers we are dialing): Executing Dial("Sip/donas-bd7b", Zap/g1/1##########") in new stack Called g1/1########## Channel 1, span 1 got hangup **Above

Hi, I have a problem with dialling internationals numbers, and I don't now what is the cause. I have one asterisk with a e100p card connected to the Telco (spain/telefonica) and it can dial local and national numbers without problems but when I try to dial a international number it hangs-up. I call the Telco to ask if the E1 can do international calls and it said that it can. I have tried

We've got a EuroISDN (32 channels) with a TE405p, running cvs head as of 5 days ago. In the past couple of days, we've hit a scenario where incoming calls to the * pbx from the PSTN are being marked as busy, but outgoing calls work just fine. When we reboot *, the problem goes away. Has anyone else had this ? I've attached a PRI debug below. I've changed the phone numbers (x

I am hoping someone could shed some light and point me in the right direction? I'm attempting to get callerid work between an Avaya Definity PBX and Asterisk via TE110P connected via T1/PRI Crossover PRI. From the Definity side I've searched endlessly and came with an example which we modeled as close as we can, but still no luck. While doing PRI intense debug span 1 in I see a couple

I have a PRI E1 link between Asterisk 1.4.24 and Alcatel-Lucent OmniPCX Enterprise R9.0. As EuroISDN it works fine. However, I need to move to QSIG because of a firmware upgrade on the Alcatel PBX which doesn't support EuroISDN (please don't ask why). Besides, I've read somewhere that 2 B Channel Transfers "should" work with * 1.4, the latest 1.4 libpri and QSIG. So this

Hi all, I have to asterisk-1.0.9BRIstuffed-0.2.0n boxes each equipped with a TE410P. Box A is connected with pri1 to the PSTN. Box B is connected with pri1 (cpe) to the Box A at pri2 (net). Now I want Box B to dial out to the PSTN tunneled thru Box A and have it get all ISDN indications in case of call failure, eg. unallocated destination number etc. But currently Box B always gets only