similar to: chan_capi and poor voice quality

Hello! I'm curently using * with two old Teles PCI card (wich, btw, were hard to install and make good use of) with ISDN4Linux. The sound quality is simply perfect. However both dialing in and out through the ISDN line, there seems to be a _little_ bit of echo that eventually gets on your nerves ! Also the echo seems to get a _little_ bigger after a minute or so into the conversation. Now,

Hello, Is it possible to use * as a gateway in the following setup: LAN (with Windows NT/Linux PCs) | Ethernet (IP) | Linux PC with * and AVM Fritz! ISDN Adapter | ISDN | Someone with a analog/digital phone (POTS) Basically, people sitting on their PCs will wear a headset, and whenever they want to call someone,

Hi list! I'm currently using a HFC-S card for my ISDN BRI line with bristuff. The instability is driving me crazy however. I'm having continuous problems where inbound calls will not work after some time of operation (the number then appears as not in use to the caller) or also outbound calls do not work. The solution is to unload the modules, stop asterisk, re-load the modules and

Good day, *newbie alert* I try to run * with capi_chan (and later on SIP). System: Debian 3.0 / apt-getted most stuff except chan_capi and b1.t4 HW: AVM B1 ISA / Celeron 400 / 128MB RAM Starting * the following ends up in the messages Jul 22 19:47:03 WARNING[16384]: File chan_mgcp.c, Line 2925 (load_module): Unable to get our IP address, MGCP disabled Jul 22 19:47:03 WARNING[16384]: File

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hello asterisk-users, I recently set up an asterisk server using Debian Sarge. I also added an ISDN card (AVM FritzCard PCI) to the machine. I built amd installed a new kernel (2.6.15.1) with modular support for the CAPI stuff and also integrated the FritzCard driver available from AVM. capiinfo succeeds in correctly showing the ISDN card. When talking from one PC to another via SIP, everything

hi all it seems like whatever I do, I can't use more than 1 BRI on my AVM C2 with chan_capi. Both channels seem to work, but not at the same time. And - yes - they're connected to different NT boxes :) Any ideas? kapejod? -- Roy Sigurd Karlsbakk, Datavaktmester ProntoTV AS - http://www.pronto.tv/ Tel: +47 9801 3356 Computers are like air conditioners. They stop working when you open

I have 10 msns on my isdn bri incoming (AVM Fritz, chan_capi 3.5) When i set in capi.conf [interfaces] msn=1,2,3,4,5,6,7,8,9,10 incomingmsn=* controller=1 softdtmf=1 accountcode= context=tcom-in echocancel=yes devices=2 Only msn 1,2,3 are working. What can i do? Thanks Jens

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Has anyone got the BT Speedway (AVM Fritz) card working on a RedHat 8.0 system with *. If so could someone give me some pointers on getting the right sequence of installing the drivers and which versions to use. Thanks, Stuart -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I'm having a problem with DTMF tones from my SIP client apparently crashing the chan_capi driver. However I'm not sure whether this is a bug or misconfiguration on my part: if I set "softdtmf=1" in /etc/asterisk/capi.conf the problem goes away. Does the AVM B1 not support DTMF detection? The set up I have is using latest CVS (3 days old) running RH8 on a 933MHz P3. SIP

Hi, my setup is quite simple: an asterix CVS of 2003-11-15 on a 2.4.21-debian-5 GNU/Linux box in an internal network (192.168.1.0/24, asterisk is 192.168.1.10). - with a SIP phone configured as 192.168.1.190, and with its SIP server being 192.168.1.190 - with an ISDN AVM c4 i4l card on an ISDN connection with 2 channels. I try to: - dial-in from ISDN, then transfer to the SIP

I'm getting a strange error on one of the two controllers on an AVM C2 card under chan_capi-cm-0.6.3. I have two ISDN controllers defined, both in the same group, both connections are UK ISDN2e Point to Point: On the third outbound call (both of the first two calls are handled by the second controller "ISDN2",) I get this error : chan_capi.c conf_error 0x2001 PLCI=0x301

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

Hi, Is it possible to use 2 B channels simultaneously with either I4L or CAPI drivers? We use AVM A1 (Fritz) PCMCIA with I4L driver and AVM B1 PCMCIA with CAPI driver. Thanks, Michael.

Hi! I'm goining to connect an AVM C4 to 4 BRI-lines in PTP-Mode, all BRI-lines will have the same number (1234-XX for example). I don't know if this is possible and I can't test it, because I don't have these lines yet. Is anybody out there, running such a configuration? I'm looking for some example configs. Especially I want to know how it is possible, to let asterisk

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Hello, first of all I have to say: I read the handbook but there are some questions left I couldn't answer. It's very basicaly. Sorry about that. I have a AVM B1 PCI - Card. I think there is a I4L and a Capi-Port installed. 1. How can I define the right channels, how are they defined. I found the modem.conf example with an ISDN section but how can I make asterisk load it? 2. Do I

I had unexpected hangups from my asterix box using the i4l driver. (SIP <-> SIP calls worked execellent, but SIP<->ISDN didn't.) Then I changed the i4l driver in modem.conf with the chan_capi from jungham. (http://www.junghanns.net/asterisk) I followed his instructions in the INSTALL file, and first encountered some errors compiling it. It help by deinstalling several