similar to: Robbed bit signalling debugging

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Hi, We've got a dedicated T1 with two trunks running into our ILECs selective router for 911. Split out of the T1 into two MF CAMA trunks on ILEC side. I'm trying to use asterisks e911 signaling, but I'm having trouble with the dial command. (== Everyone is busy/congested at this time (1:1/0/0)) I'm missing something and I'm thinking it has to do with the hookstate

We have had quite a bit of success with our T100P and TE410P cards interfacing to Nortel Meridian PBXes and also to a Livingston Portmaster 3 using ESF/B8ZS and various combinations of E&M wink and ISDN PRI (usually in 5ESS mode). In the near future, I may also need to interface to a Definity via a T1. I was planning to use PRI--is that an option for you on your switch? -----Original

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

Hi All, I'm trying to configure a Digium T100P to talk to a legacy voicemail system. I have the signaling specs verbatim from the original manufacturer documentation as follows: [T1 Signaling] Service Type: T1,D4 format, AMI(Super Fram) Signaling: Four wire, terminated, E&M (Robbed bit) Start Protocol: Wink start; 250msec duration Dial Tone: Enabled Digits: DTMF, 4-digits DTMF: 50msec

> -----Original Message----- > From: Jerry Geis [mailto:geisj@pagestation.com] > Sent: September 8, 2004 2:19 PM > To: asterisk-users@lists.digium.com > Subject: [Asterisk-Users] T100P calls with playback starts speaking > before pickup > > > Hi > > I am using a T100P connected to a panasonic phone switch using T1 and the > switch has 4 analog lines

Ok, I'm about to take the plunge, and am trying to decide between Channelized T1 E&M and PRI. I'm getting an "Integrated T1" which will have data and voice capability, all plugged directly into my digium single T1 card. In either case the data piece looks pretty straighforward, just setup the channel properly, hand it off to the linux hdlc layer, and route away.... the

I've been having some problems getting a channelized T1 working with a T100P card. Perhaps someone can help: I have an Eschelon T1 coming into a Vina Integrator box. This box splits out the T1 into an ethernet plug for bandwidth and a secondary T1 which I plug into the T100P card. I've connected the two with a T1 crossover cable. I get a green light on the t100p card and can make

All, Alright, I've looked around the internet, the voip-info.org wiki, and browsed the contents of this mailing list. While I've found a couple of scenarios that are close to this one, I haven't found one that uses my particular card (T100P). Without further delay -- I have successfully configured internal SIP services between a Snom 200 and a Windows X-Lite client and have

Has anyone here used T1s with RBS with asterisk? Cary Fitch

Hi List, a number of our customers are reporting dropped calls. here is the config. 1 T100P T1 Card 1 Asterisk (Mid Nov build) T1 is signalled as a PRI(National) The card will only sync up if we clock, if we line side clock the card goes into yellow alarm and won't sync up. the only errors we see are framing slips. Around 2500 slips over a 18 hour period. (this was reported from

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

I have an nec electra elite 192 with a t1 card; and am looking for suggestions as to integrating them (can't throw out the system yet!). I have a fully working asterisk server -CVS-04/27/04-19:01:05- (found a hp d220 for $350.00!), 2 digium t100p cards, a plain t1 with loopstart signaling, and 2 working bt102 grandstream ip phones (thanks again Matt for your "start from scratch"

I've compiled Asterisk on Redhat 9 and Fedora Core 1 in the past, generally without any problems. Especially w/ the stock kernel, which I generally loathe. When I tried to upgrade my Redhat 9 Server to the 2.4.27 kernel, doing a manual/clean compile, I had massive quality issues. I was forced to go back down to a stock 2.4.24 kernel. Never figured out why. Now, I've installed Gentoo

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

I have TE405P span connected to a patton/digi 2977 T1/PRI port. Zaptel starts up fine without any errors. Libpri is installed as well. But I get the following when trying to load asterisk ------- Jul 3 19:30:26 ERROR[8192]: Signalling requested is PRI Signalling but line is in Unknown signalling 896 signalling Jul 3 19:30:26 ERROR[8192]: Unable to register channel '25-48' Jul

I am having a problem trying to do inband DTMF passthru via asterisk. My setup: PSTN gateway MAXTNT v11.0 SIP (T1 PRI/NT2) Asterisk HEAD or v1.0 makes no difference (I am using HEAD mostly) 12/10/04 and 01/17/05 (no difference) CAC ABII-T100P to/from analog lines to/from asterisk BTW, I have used a ABI and it works just like the ABII with asterisk. What I am seeing is: I make a call from a