similar to: CAC Access Bank

Hello Astrites, I was just about to send out a long email about not being able to detect hang-up with my CAC II FXO module on my PSTN POTS lines. I had tried many configurations. I had attached a toner to the line to see if I was getting this "disconnect supervision" signal after hang-up. (toner has a line powered light in the off position) It seemed that I was getting the signal,

Callerid issue 1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone if yes then we beleive the CAC is passing fsk 2) in chan_zap->ss_thread around line 4154 (current cvs) if you get to the callerid_feed at least once then if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs) does this parse fail

Hello, I have a CAC Channel Bank I with FXS cards. I've the system up and running, with just 1 issue. When I make an inbound call, Asterisk says "Zap/26 is ringing", however, the phone never rings. No lights are lit on the CAC during the calll. Outbound call works no problem, and the CAC lights up correctly. Any ideas what could be the problem? -- Richard Cook

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part

Ok, the Zhone sucks and the Adtran 750/850 seems to be a little too expensive. Can anyone recommend a decent channelbank that won't break the bank? TIA, -- Troy Settle Pulaski Networks http://www.psknet.com 540.994.4254 ~ 866.477.5638 Pulaski Chamber 2002 Small Business Of The Year

Hi all, Don't know if anyone can help me. We just set up a CAC Access Bank 1 with Asterisk. Everything works great except, when we ring a Zap interface, the analog phone does not actually ring. The light blinks, and if you answer it you are connected to the person, but the actual phone does not ring. Using the "Test" option for the channel does make the phone

Hi guys, I posted a somewhat similar question about a month ago and got a thoughtful resonse from Steven Critchfield, but I've got a quick follow up question to it. I'm looking to setup a 16 extension / 10-14 phone line Asterisk install for a customer who would like to have DID numbers for the extensions, since they're currently on Centrex and already have the 1-to-1

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

Can someone recommend a good quality 24 or greater port channel bank? Steve -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070506/e5896021/attachment.htm

Need to add some fxs and fxo ports behind a fonebridge2 box any recommendations a channel bank Thanks Mark -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070829/1131cad4/attachment.htm

So I made the mistake of buying a Carrier Access channel bank without noticing the page on the wiki about the fact that they don't support disconnect supervision (bastards!). However, apart from that, I do have it working fine for incoming calls. Is there some trick to get asterisk to detect the hangup tones from SBC? I've tried busydetect and callprogress as suggested, but neither

Hey all, I've been seeing this repeatedly and am wondering if anyone has a clue what's causing it.. at least once a day I see two zap fxo channels being bridged, and hanging..now, these two channels should never bridge, but they keep doing it.. any leads on where to look for what's causing it? here's what I see when I 'show channels' Zap/37-1 s@from-pstn:1

Can anyone help with getting the new DoD CACs (Smart Card) to work in CentOS 6.6? I don't use it for console logins, only for email and .mil web sites. I recently had to get a new DoD CAC (Smart Card) when one of the buildings I work in upgraded their security system. My old CAC was working fine prior to this for signing and encrypting email and for authenticating to various DoD (.mil) sites

Jon, I actually had some more discussions with Tim on this issue, and it seems that the channel bank would still be a good option to choose for internal purposes. I would not see any other solution than a channel bank to connect many 2wire phones into one asterisk box. I had a talk today with Carrier Access, and it seems that the adit would do us fine. The fxs cards of the adit 600 are

So, I'm still having this problem with outbound calls not working when using a channel bank. I've purchased a Rhino FXO channel bank from VoIPSupply.com to make sure it wasn't an equipment problem. I am using a Digium TE411P card, and have simplified it down to just 1 port plugged into the channel bank, with just 1 analog line plugged in. If I place an inbound call on the line, it

Anyone ever thought about an Ethernet based channel bank? Basically a rack mount set of 24 IAXys? That would be cool, IMO. No wrangling with zaptel, etc. IAX as the * <-> Channel bank protocol. Just an idea...

We are a voip terminating company, we're using Channelbank with FXS modules, Rhino, CAC, etc.. What we're wondering is, is how to would you echo cancel a channelbank. Of course we're realizing that cancel'ing on the T1 (on Ast) does no good (we think?) because the analog conversion is at the channelbank. Suggestions? Lowering the gain helps but we're looking for a real solution

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

I'm going to install asterisk with four digium cards. Can anyone mention a brand that carries boards with 4 compatible pci slots? Thanks Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd. Office: +972-3-9230686 ext. 179 Fax: +972-3-9216642 Mobile: +972-54-8000200

Hello, I am working for a charity in the UK and I am projecting a new phone system. We would like to connect our two-wire telephones (40 or so) to an ADIT 600 channel bank, and connect that into an Asterisk box via the CMG card or T1 card. I have been in talks with Carrier Access about the purchase of a new channel bank and we tried to get a minor version of it first for testing with the