similar to: Cisco 7960 config?

I have three questions about my 7960 phone that I can't discern from the docs/wiki. 1st - If I change the SIPxxxxxx.cnf file to change registrations it sets up new lines as expected. If I delete a line it doesn't get removed when I reboot the phone. I have to go to the phone, unlock it, and reset the SIP parameters. How do I make it "forget" what it has programmed and

-----Original Message----- From: Adams, Gavin Sent: Monday, August 04, 2003 6:10 PM To: 'asterisk-users@lists.digium.com' Subject: Cisco 7960, SIP, NAT, Voicemal Hey all, I've got a couple 79xx phones working peer-to-peer and am now trying to work on the voice mail. In extensions.conf: [ATL] exten => 4001,1,Dial(SIP/gadams)|10 exten => 4001,2,Voicemail,u4001 exten =>

Dear All, I'm trying to configure my new phone Cisco 7960 to work with asterisk. I followed http://www.asteriskguru.com/tutorials/cisco_7960_ip_phone_configuration.html and I got into the point where I can see on the the display line indication showing "55 <phone icon with x>" so it looks like the phone is not registered. The phone and the asterisk are in the same local

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031207/e5e9b8eb/attachment.htm -------------- next part -------------- Hello all, I am newbie to Telephony world (IP and PSTN). Please excuse me if you find my questions very dumb. I am trying to configure my IP 7940 with the Asterisk, when phone boots up it only shows the message "Phone

Hello all, I've got a Cisco 7960 running version 7.4 firmware (heard there were problems with 7.5) and I can't get it to register with Asterisk. I've stripped down my configs on the phone to a bare minimum, and posted them below. Basically, the Cisco phone sends absolutely no packets to the proxy when it gets booted. If I make an outgoing call I see traffic getting to Asterisk, but

I'm starting out w/ a Cisco 7940, running the Sip image version 6.3. I've downloaded/installed asterisk via cvs. I've set the phone up to get its info via dhcp - the dhcp, tftp, astericks box & phone are on the same network. I've gone through and setup a test account per the instructions @ http://voip-info.org/wiki-Asterisk+phone+cisco+79xx but time I do a sip show

I need to set up an office full of Cisco 7960 phones behind NAT with the server out in Colo. The first test phone registers fine, but the second one does not register. The first phone's registration looks like so: /SIP/Registry/3115552368 :64.169.xx.yyy:38836:3600:3115552368:sip:3115552368@64.169.xx.yyy:5060 When the second phone tries to register, it gets back a 404 not found. Not a

Hi all, So I have been reading through the docs available online and the different threads on this list, but I cannot seem to get this phone to work. I have configured the OS79XX.TXT and SIP/SEP*.cnf files (see attached), when I configure the phone to point to my tftp server and reboot it I get this message: Connection received from 10.6.0.224 on port 50608 [09/02 12:16:11.750] Read request

Hi everyone, I googled this followed the instructions, but it hasn't work for me yet. I have universal setting in SIPDefault.cnf and phone specific settings in SIPXXXXXXXXXX.cnf. But it doesn't get registered. I need to register it on two different asterisk boxes. So my SIPXXXXXXXXXX.cnf looks like this: phone_label: "Zeeshan A Zakaria" line1_name: "523"

This I am sure is a very easy question, but I can't seem to find the answer. Here is the scenario: cisco 7940g phone has SIP 6.3 firmware applied the file SIP<mac>.cnf does not seem to have a place for it: image_version: P0S3-06-3-00 #line 1 settings line1_name: "5010" ; Line 1 ExtensionUser ID line1_displayname: "5010" ; Line 1 Display

Hi All Total noob on the list so all help appreciated.... I've successfully installed Asterisk on an IBM A30P Thinkpad using fedora Core 2 (I'm looking at having a mobile PBX for conferences and shows). I've plugged in two Cisco 7960 phones.... The phones register with the Asterisk correctly and I can run the demo's and even the AIX demo through to digium works correctly.......

Hi all I have a problem to register a cisco 7960 to an asterisk 1.2.2 I defined in sip.conf the next : ["phonenumber"] type=friend username="username" secret="password" host=dynamic context=work I am trying to catch the register requests with sip debug with no success (empty screen). I can only catch the register messages with ngrep on host it's comming

I'm trying to get inbound calls from a TNT working but get 407 errors from the TNT. This is what I have in sip.conf: [maxtnt] type=friend host=x.x.x.x dtmfmode=rfc2833 callerid="MaxTNT" <maxtnt> context=demo qualify=yes disallow=all allow=g729 allow=ulaw insecure=very This is what the TNT is spitting out: Jul 24 14:55:12 tnt1 1/17: Releasing

I have an *ipphone 7965G* which has to be connected to Asterisk. It has been flashed with SIP firmware but the config file doesn't seem to work maybe I am missing something in it. I appreciate it if you can share your working sample config file with me. Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am using IAX to send a call to my cell phone. I want to be able to hit # and transfer it back into the office. I have added tTr to the dial command and hitting # prompts me for the transfer, but after I start dialing 103, it stops at 1 and tries to transfer it within nufone instead of my dialplan. This is the debug output: -- Called me@NuFone/1515480XXXX -- Call accepted by

Anyone have experience with the 3-08-2 release of Cisco's SIP firmware? Are there any new features in the SIPDefault.cnf? Thanks, Ron

Hi, I am upgrading a Cisco 7960 phone from SIP V.5.1 to 6.0 and then will to go up to 7.5 However in my first attempt to go from V.5.1 to 6.0 this is hat happens: - The phone reboots - The phone then reads the file OS79XX.TXT from the TFP server. In the file I added the version "P0S3-06-0-00" - It starts upgrading firmware - Then I get the following message: (Upgrade Failed -

I've searched around and found a few similar situations where the phone will call out when using a Asterisk server but not receive inbound calls. My issue is a little stranger. If I call out from the phone then the phone will receive the next inbound call. The phone will not receive another inbound call until a call out again from it first. Any ideas? I am using SIP and am using the latest

Can you also post information such as: Type of phone (model Number would be idela) How is it conencted, SIP, ZAP, IAX, Channel Bank. Corresponding config files would also help. Help us help you. >>-----Original Message----- >>From: asterisk-users-bounces@lists.digium.com >>[mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of >>Paul A Brown >>Sent:

Hi, First off, a big thanks to Digium (Mark, John, and Martin) for helping sort out a BellSouth config issue on our PRI. T100P working like a champ! Now it's back to tweaking the configuration on our SIP phones (7960s). The message_uri parameter in the phone's configuration file is working great. Dials comedian mail directly. Is there a way to let voicemail2 know what the incoming