similar to: Dual T400P, SMP, performance issues

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Anyone care to elaborate on the differences between the T400P and the TE405P? -Darren -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050908/e817f8bb/attachment.htm

Below you will find, what I believe to be a typical setup with a T100P card. My question is - 1. Is this correct? 2. What kind of phones would be needed here... (Would you have to use Digital phones) And if so what would you recommend. PRI/T1----- | | | ---------------- | | | Channel Bank | | |

Can T400P be configured for nfas (one d-channel providing signaling for more than one span)? Thank you. Alex Zarubin -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030522/f2b637a9/attachment.htm

Modem connect speeds on calls through * seem to be lower than calls made through the telephone company lines or our old Rolm PBX. All data calls have 2 wire analog modems on both ends. For my set up I have channels of a Zhone channel bank tied to 2 modems. The Zhone channel bank interfaces my * server with a T400P card. modem --- Zhone Channel bank - * via T400P card - Zhone channel bank -

Hi, Is this card the same as the T410P, after all, it's made by Digium. There's one prior reference on the mailint list[1] but it didn't answer the question. There was also an SS7 status report[2] last June but it's doesn't seem to have lead anywhere either. There was post saying an SS7 release was immenent last September[3], but then silence. Any info anyone would like to

Hi, I've posted this question on OpenSS7 mailing list but I didn't get a clear answer. I have a system running asterisk using Digium T400P card. Can this same card be used with OpenSS7 project to carry SS7 links? Is there any difference between these two cards? -- Matteo D'Amato Network/Telecom Administrator Intelco Communication Inc

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

We have been pretty much able to solve our echo problems, except for the primary mode in which we desire to operate our system. See system diagram at bottom. Prior to making adjustments to cancel echos (all echocancel=no): Call Type Result (Before) --------- --------------- CP <- LEC PRI * TDMoE * FXO -> AP

I've been trying to get a Win 2000 RAS server working with my asterisk PBX for quite some time, to no avail. I've googled, I've tried loads of configurations, I've rewired phone lines, and still I am not winning the battle. Here's my config. PRI->T400P->Asterisk->T400P->Adtran 750(L36 Firmware)->RAS Server. I have 4 Zap channels signalled FXO_KS to the 750

Hi, I have scanned through the archives of this list and found a number of question about hardware, but I just can not find the answer to my question. I am new to phone systems, I got "drafted" to come up with a new phone system for our company (I guess they figure since I know computers I know phone systems as well :O). We have 5 analog (I guess they are called PSTN lines) lines coming

Ok, if I missed something in the wiki please point me there with the correct search terms. Asterisk 1.0.7 (AAH really) 4 co lines from Bellsouth into a Diguim T400P. Polycom 501 x 4 on the desktops. My problem is on calls to or from the CO I hear a "pinging" (thing sonar ping in a submarine) every 12 seconds. You can set your watch to it. COuld this be a "call recording in

Could anyone with any experience with * over a non-PRI T1 help this newbie? I have a fractional T1 that is working fine through a channel bank, but I can't get any response on * using a T400P. My analog line and the extensions work fine, but the T400P port 1 shows a red led (what exactly does that tell me?). I brought up zttool which shows a condition red also, but ztcfg shows nothing amiss.

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

System is built on a SuperMicro motherboard with Serverworks chipset, IRQ is not shared. Have a dialplan that worked for 8 months without errors, tried reverting to older release then upgraded to 1.0.3 stable release, currently running on fedora core 1 kernel 2.4.22-nptl.2199 (have tried plain jayne), telco says "it's not us", HDLC abort seems to occur when when a Zap channel hangs

Does anyone know if there are any plans for Zapata or anyone else for that matter to come out with a 3.3v PCI version or PCI-X version of those cards? Gene

Hi, I believe the issues raised by this message are the same as mine, more on a commercial sense than for self use, but mostly the same. I've seen posts where real-life installations are mentioned, but not a reference to how Asterisk is working on production (and productive) environments. Any experiences would be very welcome I believe, not only on pure technical, but wider, sense. Thanks

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

I'm trying to hook up a non-PRI fractional T1 using a T400P port. The Telco says that it is provisioned as AMI with SF (not ESF) and that they are signalling by "sending down a straight DS1" (I'm not sure what exactly that means). They are also sending DNIS over these channels. I currently run it through a channel bank for my IVR application and it works fine but I am now