similar to: Adding an app

Thanks for the help. I was able to get my application to load with Asterisk, now I just need to get it to work. After reading your comment, I don't know that I fully understand what's going on as far as the channels and extensions. Are you saying that the MWI is tied to the channel? If that is the case, then for my SIP phones, would the channel be (SIP/XXXX)? If it should be, then

After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of which do not have "phone company" compatible FSK/stutter MWI, I finally got smart and found out just which Panasonic phones have this feature. Only the following 5.8G models in their current line have FXO compatible MWI. I purchased the 5771 unit and one remote. I have confimed it does in fact work with Asterisk

I need to setup MWI on a few Aastra 9112's. I've tried doing so in the web interface by setting "Explicit MWI Subscription" to true, but no lights, no stutter tone. Firmware: 1.4.0.1048 Thanks! -- Warm Regards, Lee

I have a quick question... In the previous thread http://www.marko.net/asterisk/archives/0210/0306.html it is mentioned Mark added support for MWI to the chan_zap. Is this in the zapata.conf and if so, if stutter is turned on then the MWI is turned on with it? Geoff

Hi, Using 1.4.26.1 & DAHDI 2.2.0.2, FSK VMWI devices off a TDM840 work fine. With 1.6.1.[45] & same DAHDI, instead of the FSK spill I get a line polarity reversal. Stutter dialtone is generated as expected. Has anyone else seen this? Is there anything special I need to do for 1.6.1 to make FSK MWI work? Thanks, --Barry

Let post this question.. Because I must be real slow... The following is my config on this... group=1 context=default signalling=fxs_ks channel => 1 context=local signalling=fxo_ks callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes rxgain=1.5 txgain=1.5 immediate=no musiconhold=default usecallerid=yes

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

My grateful thanks to whoever can guide me in implementing this... I have a need to place calls via Asterisk Manager Protocol to a legacy PBX and twiddle its MWI lights. By some means I get notified that an MWI light has to be changed. Via AMP: 1. Send an ORIGINATE command honking up an incoming port on the PBX via a TA804. a. I presume that the TA804 should be a SIP channel. yes/no? b.

May be I have fiddled too much with my sipura settings but I can't get it to give the stutter tone when there is a new voice mail waiting on the asterisk box. I can either get a stutter tone all the time or not at all. Anyone got this working. Thanks Chris

I have many remote locations that dial into a central server to retrieve voicemail via IAX. Outbound calls are handled as SIP calls from a Snom to a local (to them) Asterisk server that dials the main server thru IAX. I have trained them to check their voicemail via the emailed WAV file, however some of them are, how shall I put it, idiots*, and insist that they *have* to have the MWI indicator

asterisk-users-request@lists.digium.com is believed to have said: >I don't mean to be rude to everyone who responded to this question, but >I think that everyone is answering the wrong question. The point is that >the message waiting indicator doesn't light up, at all, ever. All that >happens when messages are waiting is that the display blinks and the >phone gives a

I am trying to set up the Message Waiting Indicator (stutter tone/light) so that my cisco ata-186 will let my phones know there is a message waiting. However this does not seem to be very well documented. I found this on wiki mailboxnumber@context ... where does that go? Do I put it in my SIP.conf definition for my cisco ata, or where. In my SIP cisco definition i already have a

Sorry for the partial post a moment ago With help I got two phones communicating - PCMA/PCMU was the problem. Next stpe is to try voicemail. VM works fine, I can leave a mesage and then retrieve it - but no MWI on the phone and no stutter dialtone. I promise I've spent the requisite 4 hours + on google etc. but have really no further ideas. The setup is 2 Grandstream phones (latest

Hi.. I am about to replace my aging Nortel Venture system with an Asterisk system and 6 Polycom IP 501 phones, and a couple sipura 841's for less used areas. We have 3 phone lines here. One is SBC, one Vonage, and one Voipjet... One hangup is that I can't figure out how to pass through a voicemail waiting indication from SBC. This is important because my wife and her family all

Using a TE410P with Zhone 24FXS channel banks to power standard analog phones I can't seem to find out if it's possible to support FSK or voltage type message waiting lamps. I don't want to use stutter dial tone because of the dramatic difference in per phone cost. TIA

Howdy I have a question regarding support for picking up when the telco sends a MWI message. My client's setup is a small office with three incoming lines on a TDM400P with iaxy's and a Grandstream as extensions. I am using CVS Head from yesterday. (I was resolving a different issue.) Since they only have two voice lines, with the third as a fax, I am using voicemail from the telco.

Hello, it is possible to get MWI working with Grandstream and Asterisk? Thanks. -David

Has anyone come up with a clever way of indicating DND is activated? I've thought of stutter dial tone and using the mwi, but have no idea how to implement these. I'm using Budgetones. My concern is that users will activate the DND, then forget about it not realizing that they are not receiving calls. Thanks, G

Hi all, Configuration: Analog phone connected to TDM400p. I'd like the phone to give a half-ring (chirp) periodically when there is a message waiting. Can this be done? How is it configured? The visible "Message waiting" indicator and the stutter dial tone are working fine, but are not sufficient for me. Thanks!

Does anyone have personal experience with a 5.8gig wireless phone (system) that has an MWI that WORKS with asterisk via fxs (in my case spa3k) generated MWI. I know the spa3k does stuttered dialtone but not sure if it generates FSK MWI. I see some that state they do but I also see reviews that say they don't. Doug