similar to: Asterisk terminates unexpectedly with SIP call and G.723 codec

I have a ATA 186 with SIP firmware 3.1 when I changed the configurations to use the g.726 codec I received many erros and the calls doesn't work. I changed the fields: - LBRCodec: 6 <- the code for g.726 - TXCodec: 6 - RxCodec: 6 The errors: Jul 9 13:15:37 NOTICE[1192491824]: rtp.c:500 ast_rtp_read: Unable to calculate samples for format G726 Jul 9 13:15:37 NOTICE[1192491824]:

Yesterday, I started to experiment with Cisco to Cisco SIP calls using the g729 codec. According to the documentation, both the ATA-186 and 7960 are able to make use of the g729. >From an earlier e-mail, I made a change to the configuration of the ATA, changing the values: LBRCodec:3 RxCodec: 3 TxCodec: 3 The first thing I noticed was that when I did a sip show channels, the format had

When I try to connect to * using a Cisco ATA 188 configured with a MGPC firmware (v3.1.1), I just keep getting this message every 30 seconds or so : May 10 10:08:21 NOTICE[7913]: chan_mgcp.c:1509 find_subchannel: Gateway '192.168.1.27' (and thus its endpoint '*') does not exist Using tcpdump, I have checked that the ATA188 (with IP 192.168.1.27 and port 2427) sends UDP packets to

Hi, I wish to connect several ATA186 Phones to each other, to iconnecthere and to the PSTN using asterisk. Please tell the appropriate settings for firewall (ports to open etc.) sip.conf and extensions.conf(part relevant to iconnect). Also I would be glad to get a working example of your ATA186 configuration. I tried searching the mailing lists and several sites but did not find an answer.

I'm having a horrible experience getting a Cisco ATA-186 to work with *. I can make calls from the ATA with no problems. However, incoming calls make the ATA ring once, and then the call is disconnected. I have no problems with my Sipura 2000 or my Grandstream phones. I am running 2.16.1 sip code on the ATA 186. Neither * nor the ATA is behind a NAT. They are both on public IP addresses

I installed * to primarily test its voicemail feature. I installed it on a server WITHOUT any telco board (i.e., digium). Installation looks ok, however I am having problems. MY SETUP: 2xATAs are configured to use * as GkorProxy Asterisk is registered to my SER SIP/RTP Proxy 1.) First test - ATA1 calls to ATA2. When voicemail starts playing, it just cuts-off after 5-10seconds (consistently).

To me it's a error if I can't complete calls using the ATA configured to use the g726 codec. I just tried it usign a sipura SPA-2000 (preferred codec: G726-32) and I received NOTICES and WARNINGS, but I can't complete a call. On a zap channel: -- Executing Dial("SIP/2007-e4d8", "Zap/1/2217008") in new stack -- Called 1/2217008 -- Zap/1-1 answered

When I make a call using sip, I get the line NOTICE[327696]: File rtp.c, Line 292 (ast_rtp_read): Unknown RTP codec 19 received Repeated many times on the console ; SIP Configuration for Asterisk ; [general] port = 5060 ; Port to bind to ;bindaddr = 0.0.0.0 ; Address to bind to context = outgoing ; Default for incoming calls allow=gsm allow=ulaw

Hi, I was able to connect asterisk to iconnect's service. It took me almost two hours, but it's because I was having NAT trouble. I finally discovered that you can set the iconnect host to natrealy.deltathree.com to make it work. (for those of you who, like me, don't have the time to search the archive I'll provide a working sample in a minute) My problem was sound

This appears to have been the magic bullet for me. Thank you very much. So, the bottom line is that there is a bug that ends up making inbound calls use type=peer rather than type=user. Correct? > -----Original Message----- > From: asterisk-users-admin@lists.digium.com > [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Paul Cheng > Sent: Tuesday, August 10, 2004 8:35

Hi folks, I want to fix hole in my asterisk set up. I use Vocal as my sip proxy and * for voice mail and the g/w to PSTN, Iconnect, fwd etc. So from Vocal I redirect sip requests which needs to go 'other' places. This senario works fine. Now the issue is someone else running a vocal or another SIP proxy can redirect his calls to my * as well. Those calls two will come through general

Hi, I am calling from a grandstream phone with g723 codec through * to iconnect. Incoming context as well as outgoing context set to g723.1 codec in *. Call get connected and I can talk. However I get the following warning, which scrolls on my screen until I hang-up. [root@asterisk sath]# cat g723.1 - Executing SetCallerID("SIP/-08122ae0", "1001") in new stack --

Folks, I have to admit that I MAY have changed something (at someone's advice) on a previous CVS head (May 28), but I'm not sure. I think that it had to do with changing "digest realm," but that may be a different issue. At any rate, I had both incoming and outgoing with iConnectHere. Now, I made exactly ONE change: I upgraded to the CVS head dated 7/30. I

Hi.. I just wondering why DTMF are not recognized by aterisk on incoming calls from my SIP provider ... ANy suggesteions ?` /Mike

I am going to have to find a fix for this problem or I'm going to have to quit using iconnect. About one call in 10 or so, iconnect's gateway gives me an error (console output appended below). So upon receiving the error, which as a 4XX error means, "Fatal," asterisk gives up and drops the call. But not iconnect!! The phone at the other end starts ringing, and rings

Hello, I've subscribbed to "IConnect". I use it eclusively for outbound calling. I like the rates they charge but people I call complain about the audio quality. They say it sounds like I'm using a "cheap mic." or they complain about echo. The sound is very clean at my end. I'm using a Bundgtone phone with meadi routed through Asterisk to IConnect. It's

Clicking on the "For more information, click here" link on the Digium site nice brings back up the same page I was looking at before, without any additional G.729 information that I can see. I'm wondering if some kind asterisker out there could provide us neophytes with some "typical scenarios" where that codec would be useful to us. For instance, I assume that it

I have an asterisk Redhat 9 box running 4 hardphone extensions. Inter-extension calls are crystal clear. However when I dial out through my iconnect account I get a lot of jitter. At first I thought it was my nat gateway but after I programmed on of the hardphones (budge tone 100) for direct dial to iconnect I have clear voice transmission. I have no way of explaining this. My asterisk sip.conf

I am getting (with older image): RFC3389 support incomplete. Turn off on client if possible How do I turn that off for the DG104s? Or if I can't how do I tweak asterisk? I see posts about ATA-186's having an audiomode, but the closet I came to was inbanddtmf. I tried =0 and =1, no effect. Thanks! -- Zot O'Connor <zot@zotconsulting.com> White Knight Hackers, Inc.

Hello, Recently I am seeing this message on my asterisk console received from Iconnect. Apr 30 11:37:21 NOTICE[1125329600]: chan_sip.c:5648 handle_request: Unknown SIP command 'NOTIFY' from '213.137.73.41' It is prety annoying as it appears once every four seconds. I've seen similar posts in the archives which points me to NAT keep alives being send by the remote end. I am