similar to: Passing audio stream through Asterisk or not?

Will Vonage unlock your ATA for you for the $15? Or someone else? I have an ATA from them I would like to use with asterisk as well. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Thursday, April 29, 2004 8:16 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Vonage and * (and what

We need to configure asterisk to authenticate two sip ATAs, but the stream must go directly from one to another ata without tuching asterisk. Is this possible adding canreinvite=yes into sip.conf? is it true laso if asterisk doesn't recognize the spd (t38)? thanks Rosario -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I have been trying to get T.38 to work with clients behind NAT for the past week but with no success. I have an asterisk server on the public internet and several Grandstream (I tried Linksys too) HT502 ATAs behind NAT in different locations. I tried every possible combination of NAT, canreinvite, t38pt_usertpsource entries, I even tried asterisk 1.4.19, 1.4.24.1, 1.4.25 all with the same

We have bought and installed 10 channels worth of G.729. We reset our ATA186 boxes to use this encoding, and it seemed to be working. However, we analyzed the data stream and saw that the ATAs were sending about 4 kbps, while the stream from asterisk was still 64 kbps, which says to me that asterisk is still using ?-law. I looked in the sample sip.conf file and don't see any place to set

I've configured Asterisk 0.7.2 to work together with Cisco ATA186 (SIP,G.711. RFC2833) and OpenPhone (H.323, G.711). But there is an issue while calling from ATA186 to OpenPhone via Astrisk - when I press any key on analogue phone connected to ATA, Asterisk shows following message: -- Executing Dial("SIP/519-3781", "OH323/62.213.36.100|20|Tt") in new stack --

-----BEGIN PGP SIGNED MESSAGE----- Greetings, I've just about got Asterisk up and running and am wondering the following. Currently, I subscribe to both Vonage and Broadvoice and as such, I've got a Sipura and Cisco ATA186. Although I'm sure this is expressly prohibited somewhere in my service agreements, can I reprogram these devices to access my own asterisk server rather than

Here is the setup: Phone A (in NYC) on own bandwidth. Phone B (in LA) on own bandwidth. Asterisk box in Houston,TX on own bandwidth. Both phones contact asterisk to register. Not much bandwidth used for this as it is a few packets every hour or so. Phone A calls Phone B. Phone A sends a call request to asterisk and asterisk calls phone B. Both phones are connected and both people are talking.

Hi Is posible to make a call from site A to Site C, and my question is, the rtp data is from A to C or is from A to B to C Site A Site B Site C ata186<-------->FW<--------->Asterisk<--------->FW<----------->ata186 Thanks -------------- next part -------------- An HTML attachment was scrubbed...

I have two ATA186 running 2.14 and 2.15. I see in the SIP debugs that both ATAs keep on sending SIP registration packets over and over. The flow is as follows: Asterisk receives REGISTER packet Asterisk sends 100 trying, 200 ok with an expire of 3600. Kurt __________________________________ Do you Yahoo!? Yahoo! Finance Tax Center - File online. File on time.

Hi all, we have a problem with a reinvite sent by our SIP provider to change audio codec due to the recognition of a fax tone. After that the SIP call session has been established (INVITE and 200 OK) we have the following codec situation: UAC ASTERISK UAS | ASTERISK UAC PROVIDER g711 <----------------------> g711

Perhaps I was a little too hasty in my conclusions of dysfunctional fax on the SPA-2000. It turns out I have a one way audio problem on line one of my SPA-2000. I have all the correct settings according to the comments in the wiki, but the problem persists. However, if I do a hook flash out of and back in to the call that isn't transmitting audio, it works fine. My sip.conf entry for the

<div style="font:14px/1.5 'Lucida Grande', '微软雅黑';color:#333;"><p style="line-height: 1.5; margin: 0px; font-family: 'Lucida Grande', 'Lucida Sans Unicode', sans-serif !important;">Hi All,</p><p style="line-height: 1.5; margin: 0px; font-family: 'Lucida Grande', 'Lucida Sans Unicode', sans-serif

I am facing one way audio problem in sip trunking between asterisk and avaya. +-------------+ +----+ | avaya sip |-------| P1 | +-------------+ +----+ | | | +-------------+ | Asterisk | WAN

Do functions like call forwarding, do not disturb and so on work with SIP phones? I had these features working with the S100 USB device but can't seem to get them to work with the phones that are plugged into the ATA186s. Also, how do I get an extension that's plugged into an ATA186 to present caller ID? Thanks...

This *should* be something that's easy to fix, but apparently I'm not doing something right. Our SIP long distance provider is telling us to only use formats G.723 and G.729, so I've set up their trunk configuration in sip.conf as such: [t564] type=friend host=XXX.XX.56.4 context=default disallow=all allow=g723 allow=g729 However, the Dial application gives the following error:

We have issues with all of the SPA-2000 ATAs we have where incoming calls from only one of our Asterisk servers do not complete. Details: 1- On the CLI we see that when the call is pushed to the ATA it shows Busy/Congested 2- We can make calls to this same server just fine 3- We can receive calls from other Asterisk servers running older CVS versions of Asterisk with the same exact ATA

Hello, I am having a problem with my current SIP over VPN setup. We have a server running asterisk at our office. All the phones in the office are on the same network / local to this server. We also have two employees with home offices using SIP phones over VPN to connect to the asterisk server. These phones have no problem with calls to the phones in the office, however there is no audio

Hi list, i've problems with my * server and the 4 phones which are linked to it. i've 2 grandstream bt100 with the firmware upgraded to 101, a wi-fi phone (i don't know its brand) and another ip phone i don't know its brand. with this sip.conf : [general] port = 5060 bindaddr = 192.168.100.229 context = default ;x changed from default to sip localnet = 192.168.100.0/24

I have done my homework on this, I hope. I have a customer with an ATA186 who uses Nufone as his IAX provider. His network operations center in the Bahamas was destroyed by the hurricanes, and I'm helping him rebuild. We have a nagging problem getting his ATAs (located in public IP space) to talk through his IAX provider (Nufone) to the outside world. As far as we know, things worked OK

I really should be doing something better on this beautiful weekend, but I'm trying to save myself some time for later projects by documenting some things that have been particularly troublesome in the past. That being said... I've written up a configuration guide for the Cisco ATA-186, which describes some of the features that are possible to set in the ATA and specifically what