similar to: mkinitrd-4.2.1.3-1 unsuitable for 2.6.13+ kernels?

Hi List, I've started looking into iSCSI, and I'm wondering if there is an iSCSI target (I've found the initiator in iscsi-initiator-utils) that ships with CentOS, or if not, what the recommended target would be. I'd like to export either a partition or (preferably) a file-as-a-partition. Yours, -S -- Simen Thoresen, Wulfkit Support, Dolphin ICS

Basically the issue comes down to my Volume Groups not being found by this initrd, causing good ole kernel panic. initrd-2.6.12.6-xen3_12.1_rhel4.1.img [root@xen01 lvm]# uname -a Linux xen01.inside.***.com 2.6.9-22.0.2.ELsmp #1 SMP Thu Jan 5 17:13:01 EST 2006 i686 i686 i386 GNU/Linux [root@xen01 lvm]# cat /etc/redhat-release Red Hat Enterprise Linux ES release 4 (Nahant Update 2) Everything

I''ve compiled xen without any problems. but now i have to create an initrd file. When i use the command mkinitrd (without any options) the i''ve got some errors: # mkinitrd Root device: /dev/sda3 (mounted on / as reiserfs) Module list: ata_piix mptbase mptscsih qla2300 reiserfs Kernel image: /boot/vmlinuz-2.6.11.12-xen0 Initrd image: /boot/initrd-2.6.11.12-xen0 Shared

Hello Sir, (This applies to the RH8.0 supplied syslinux 1.75-3 and the upgraded tftp-server-0.32-1 from RH Rawhide) I'm having fun remotebooting my ViA EPIA box (an ITX form-factor 800MHz ViA C3 semi-embedded pc), and have landed on pxeboot as the 'best tool for the job'. Right now I have it working, but the documentation found elsewhere on the web has confused me. Specifically,

I have a Tyan Tiger S2466 MPX motherboard with Dual Atlon MP 2800+ CPUs and 1GB PC2100 DDR SDRAM. For disk drive I have an LSI53C1030 and 4 Seagate ST336607LWs in a software raid 5 configuration. I installed Centos 4.1 and everything was fine running kernel-smp-2.6.9-11.EL. However when I upated to Centos 4.2 I have run into problems. Namely after a finite amount of disk traffic the system

Hi all, i've installed AMP and Asterisk following the INSTALL file and i have a problem with the TDM04B with 4 FXO: [root@srvoip ~]# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default) (Slaves: 03) Channel 04: FXO Kewlstart (Default)

zaprtc 'load' is failing on my machine (the make was fine, same output as other posts to this list) [xxx@xxx zaptelrtc]# make load sync modprobe zaptel insmod ./zaprtc.o ./zaprtc.o: init_module: Input/output error Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or

Hi all, I'm wondering if I'm running into some dependency issues on my CentOS5 test-machines. I've installed with a fairly minimal package set, updated, removed old kernels and am now experimenting with iscsi and gfs. I think I need kmod-gfs to get gfs -support, but there is only a version that suits the base-kernel, 2.6.18-8.el5. " [root at node02 ~]# yum install kmod-gfs

CentOS 4.3 (SMP, x86_64, Athlon64 X2) with all pre-4.4 release updates applied. Since I ran into the Yum issue at the previous upgrade, I first did yum upgrade to get the list of packages (6 to install, 206 to update). I then did yum upgrade yum (which passed without issues) yum upgrade sqlite (which passed without isseus). Fairly certain that yum now works correctly, I wanted to just do

Hi! I am trying to export a PCI device (an AVM Fritzcard PCI ISDN card...) to a domU but when starting my domU I am getting this error: "pciback pci-4-0: 22 Couldn''t locate PCI device (0000:00:06.0)! perhaps already in-use?" My system is running both debian etch in dom0 and domU... Below you can find (hopefully) all important information... Sincerely, Gaubatz Patrick

Hi all, I'm sure this eventually will be resolved with a BIOS or kernel update, but in case someone experiences this on this or a similar motherboard, I thought I'd post a problem-and-workaround report. Platform CentOS5, x86_64 kernel-2.6.18-53.1.21.el5 Motherboard Asus M3a78-EMH HDMI SATA-controller configured as AHCI Experienced symptom; Periodic, ~20s lockups/freezes, several a

Hi all, Another FYI-mail (and just to verify that I'm not going insane here); I recently purchased an ASUS M3A78-EMH HDMI -board with a tri-core Phenom. This is a small uATX-board with all the garnish integrated motherboards are supposed to come with, and fairly well supported in CentOS 5 and other modern distros. When I installed it (~2 months ago) the NIC was not supported; Ethernet

Alle, I am trying to install CentOS 5 on a Dual Xeon 5160 FJ RX200 S3. The RAID hardware is an internal LSI MPT 1068 SAS/RAID controller (LSI 1068SASIME-2300). I have downloaded the drivers (mptsas, mptscsih and mptbase) and created the required floppy. When I run linux dd after booting from either the DVD or Disk 1 of the CentOS distro, it says it loads mptsas, mptbase and mptscsih and

Hi people, I ran into one of these silly issues I'd like to share as I think the reason behind it may be a flaw in the current initrds. The setup; Dual-Xeon Intel-chipset motherboard. SATA-disk attached to ICH, onboard Adaptec SCSI-controller. Installed system, updated packages, no problems. Basic, non-LVM partition setup - OS-disk is /dev/sda, single filesystem-partition /dev/sda1 is

Hello all, I have a problem with Xen and FibreChannel. The Dom0 can''t export a Disk on a FibreChannel SAN-Box to the DomU''s. In the DomU configuration I try: disk = [ ''phy:/dev/sdb1,/dev/sda1,w'' ] or disk = [ ''file:/mnt/sambashare.img,sda1,w'' ] sambashare.img is a 512MB great Diskimage on a Partition on the FC-SAN-Box, the Dom0 mount this

I am unable to boot Dom0 on a machine with Reiser file systems. Reiser support is built into the xen0 kernel. I have similar setup with ext3 file systems working just fine, so I don''t think it is a setup problem. I have tried booting with and without and initrd file, booting with the original Linux distro initrd file, etc, but nothing seems to work. I recall seeing a thread about ReiserFS

All, I am running xen3.0.2 and xen unstable on RHEL 4, and get this error when trying to boot Xen kernel(domain0) ...... Creating root device Mounting root filesystem mount: error 6 mounting ext3 mount: error 2 mounting none Switching to new root switchroot: mount failed: 22 umount /initrd/dev failed: 2 Kernel panic - not syncing: Attempting to kill init! Then system reboot.In grub.conf,I have

All, I am running xen3.0.2 and xen unstable on RHEL 4, and get this error when trying to boot Xen kernel(domain0) ...... Creating root device Mounting root filesystem mount: error 6 mounting ext3 mount: error 2 mounting none Switching to new root switchroot: mount failed: 22 umount /initrd/dev failed: 2 Kernel panic - not syncing: Attempting to kill init! Then system reboot.In grub.conf,I have

NOTE: this is happening on Centos 6 x86_64, 2.6.32-504.3.3.el6.x86_64 not Centos 5 Dell PowerEdge 2970, Seagate SATA drive, non-raid. I have this server which has been dying randomly, with no logs. I had a tail -f over ssh for a week, when this just happened. Feb 8 00:10:21 thirteen-230 kernel: mptscsih: ioc0: attempting task abort! (sc=ffff880057a0a080) Feb 8 00:10:21 thirteen-230 kernel: