similar to: Need help with zapata.conf

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the

So I have an X100P, and a TDM10B both working (at least I think they are). The drivers have been loaded and ztcfg -vv shows no errors in the configuration of two channels. When I run asterisk -vvvc and pick up my phone (plugged into TDM10B), I don't gear a dialtone. in phone.conf, I have [interfaces] mode=dialtone format=slinear ... Shouldn't that produce a dialtone when I pick up the

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi, I' ve just connected a carte X100M to my asterisk server running zaptel-1.2.5, libpri-1.2.2 and asterisk-1.2.6 on SUSE 10.0. When I make modprobe wcfxo and modprobe zaptel I haven't any error, I have also chan_zap.so module existing in /usr/lib/asterisk/modules. But, when i run ztcfg, it shows me this: Zaptel Configuration ====================== Channel map: 0 channels configured.

Im getting the following error when I try to start Asterisk WARNING[16384]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Nov 29 21:40:43 ERROR[16384]: chan_zap.c:6195 mkintf: Unable to open channel 1: No such device or address I'm using a TDM22B card. ============= # Zaptel Configuration File # loadzone=us defaultzone=us fxoks=1-2 fxsks=3-4 ==============

Ok. I am confused. I now have conflicting answers to my question: Do you need to use a special phone to use SIP? My setup is X100P and TDM10B. I would like to connect to iConnectHere, which uses SIP. Has anybody done this before (using similar equipment to what I have listed above)? And if it is not possible, could somebody please explain why. I don't understand why this wouldn't

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hi, Would someone assist me with the configuration of my TMD10B and X100P cards? I would ask Digium but my support was good for only one install...( I had to rebuild my * box). I wrote down the configuration but I must have made a mistake somewhere. I have followed the instructions on the Digium site but I must be missing something. Here's the config (snippets) I've been attempting to

Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an

Hi I am in the middle of move a small business over from legacy PABX + PSTN lines to VOIP infrastructure. I borrowed a spa9000 to place between the PABX and the PSTN lines. I have had this going for a while (>5 months) and it has been working fine (some issues with echo and other minor things), which is why I am moving to asterisk. I bought a tdm410 with 3 fxo + fxs. The fxs is connected to

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

I just received two TDM400P cards, but I'm having problems with them. The full info is at: http://pastebin.com/824079 Extra, I'm using : libpri-1.2.3 zaptel-1.2.10 On a x86 stable Gentoo box. Kernel: 2.6.17 gcc-4.1.1, glibc-2.4-r4 Is that an hardware problem? Should I try the other card? -- Gustavo Felisberto (HumpBack) Web: http://dev.gentoo.org/~humpback Blog:

I have seen this in the archives any number of times -- but I have yet to find a solution that works for me. Any suggestions you can offer would be most appreciated. Here are the answers to the questions I have seen asked in earlier posts. The log contains: Mar 10 12:26:29 WARNING[3015] chan_zap.c: Unable to specify channel 4: No such device Mar 10 12:26:29 ERROR[3015] chan_zap.c: Unable

Hello List, i am trying to set up an * box with a debian 2.6.10 Kernel. the compilation of asterisk and the zaptel drivers worked almost perfectly. so i did modprobe zaptel modprobe wcte11xp (which is the correct driver for my card) ztcfg -v and this results in ZT_SPANCONFIG failed on span 1: No such device or address (6) I don?t have any ideas whats wrong. google was no help, checking sources

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

I need help creating a channel for my phone device (Quicknet PhoneJack). I have installed and loaded the driver and phone devices listen in /dev (phone0 - phone15). [phone.conf] mode=dialtone format=slinear device => /dev/phone0 fxoks=2 ;Quicknet PhoneJack [extensions.conf] ... exten=>_NXXNXXXXXX,1,Dial,Phone/phone0 ... When I try to make a call, I get the following output: Executing