similar to: X100P odd state behavior on shared/split line.

Hi all. I`ve installed a X100P on my box and is working well with incoming and outgoing calls as a trunk with one PTSN line. I want to connect the X100P to my Panasonic 616 EASA-PHONE as an internal extension to permit to users to make calls to SIP devices from analog phones, the problem is when I dial the ext number where the X100P is connected I get busy tone. What config I need to change to

I have an X100P connected to an extension of a Panasonic PBX. When a call from the PSTN comes in, it is routed directly to the extension where the x100p is . I want * to answer the call, play a message and then transfer the call to another extension via the Zap channel where the call was received (I need to flash the zap channel) . If this extension doesn't answer I want then to dial an IAX

Hi All... I have installed a single X100P card in my PC and am playing with Asterisk. The wire I plugged into the X100P has two POTS lines on it, wired on the RJ45 in the normal way. I am getting odd behavior. It seems when I dial out that the X100P dials both lines at the same time. I have two questions. First, I see that the X100P is only a single channel. Does this mean that I can

Thanks for the information Lee ! Still, something is still strange to me, since this two Panasonic Fax machines are receiving at least 20 multi-paged faxes a day (they are in same office as both Asterisk boxes, and me :) ). Beside that, POTS lines in those two faxes are from same PSTN switch as line in X100P in one of Asterisk boxes, and the ISDN PRI lines in other Asterisk box is from same PSTN

Hi, I'm currently running asterisk 1.0.9-r1 and zaptel 1.0.9_p1-r1 (the current gentoo ~x86 versions), with the UK CallerID patches from http://www.lusyn.com/asterisk/patches.html applied. The Zap interface itself seems to work fairly well - although it's a little quiet, there is no echo. Unfortunately, there's also no CallerID. My zapata.conf is as follows: [channels]

Hi. I've searched the archives and found nothing regarding collaborating Asterisk with a Panasonic PBX (TD1232 to be exact) Here's my question: Can I use a Wildcard X100P to connect an outgoing line jack (on the Panasonic) to Asterisk, so I can route calls from the PBX to Asterisk, and calls from Asterisk to the PBX? On the hardware page for the X100P card is says it's great for

I currently have: Telco-PRI ---- Panasonic DBS576 PBX ---- E&M wink T1 ---- Asterisk. I have configured the Panasonic to forward my Asterisk DIDs to the Asterisk extensions over the T1. I do not get DID nor CID on the Asterisk, so I want to use PRI between the PBXs. I do not want to pay for another PRI card for the Panasonic. (T1 and PRI are different cards) I see this as my least

I've got a single phone line coming into an X100P. In extensions.conf I've got this: [inboundzap] exten => s,1,Answer exten => s,2,EAgi,hanguptest.agi I see the ring come in and Asterisk detects it and tries to do something with it: NOTICE[20492]: File chan_zap.c, Line 4017 (ss_thread): Got event 2 (Ring/Answered)... -- Executing Answer("Zap/1-1", "") in

Hey folks, I have a Digium TE205P working as a man in the middle: PRI line -------- Asterisk/TE205P -------- PBX The PBX is a Panasonic KX - TVP 100. Everything is working great except for one little issue. Asterisk isn't hanging up the PRI B channel when the PBX channel is hung up. I don't want to overload you with information but please ask if more is needed. I suspect I'm

I've configured my [*] to dial the pstn which is working like a charm. I've also configured an extension to ring when the PSTN line is ringing which is also working brilliantly, but, sometimes it doesn't detect that the call has been hungup. I've had a look on voip-info and checked the conf files but I can't see anything that I've missed. Cheers Matt

Hi, Anyone know anything about Asterisk's support for door phones? Receiving the call from the door intercom system, opening the door, etc? Any hardware recommendations? I understand that the equipment we have now is Panasonic proprietary and came with the currently deployed Panasonic TD12-32 pbx. We intend to deploy Asterisk in a 72 extensions + 16 trunks in a while, so any info will be

I have been experiencing hung up when answering incoming calls through x100p. NOTICE[1242768320]: chan_zap.c:4584 ss_thread: Got event 2 (ring/Answered).. -- Executing Wait("Zap/1-1","1") in new stack -- Executing Answer("Zap/1-1","") in new stack -- Executing DigitTimeout("Zap/1-1"."5") in new stack -- Set digit timeout to 5 --

Does anyone know if it is possible to use the following disconnect tone setting with an x100p card? Disconnect Tone: 350@-19,440@-19;4(.25/.25/1+2) This tone was written for a Sipura SPA-3000 for a Panasonic KX-TD1232. The Panasonic does not support disconnect supervision, so this tone is the only thing that will detect a disconnect. It is not a standard fast busy or offhook tone.

Folks, For the last few days I've been trying to experiment with a Panasonic PBX and an X100P but have run into quite a few problems which I am not sure if they can be solved with this type of card (how about TDM01B?) 1) I wanted to use *'s IVR capabilities, so I routed the calls to the extension where the x100p was connected to. Asterisk should answer the call, playback a message,

Hi, I've got an x100P and I'm able to dial out and make phone calls with it ok but I just want to set it up to answer the phone and be a simple answering machine but it doesn't seem to want to answer the phone. I keep getting this: on the console when the phone rings: -- Starting simple switch on 'Zap/1-1' Nov 28 08:55:09 NOTICE[29298]: chan_zap.c:5458 ss_thread: Got

Hello. I've got a Samba server and I'd like it to be master browser and everything else except domain controller (the customers wants a workgroup, not a domain). Lately a Windows 2003 server was added to the net and then I guess it was removed. I keep getting messages like the following in the logs: > Apr 10 03:07:51 apocalypse nmbd[57552]: [2005/04/10 03:07:51, 0]

Hi All, I wasn't too sure how to word the subject, so I apologise for that. Anyway, I've got two X100P cards here accepting calls. Basically in Australia our ring cadence is 400ms on, 200ms off, 400ms on, 2000ms off, repeat. What I've noticed is that it takes about 8 seconds after the caller has hungup for the internal phones to stop ringing, whereas in Australia the maximum time

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

I have an Asterisk server running todays CVS (updated it just in case that was the problem). It has 3 X100P cards. The first two lines I use as my normal work lines and the third is my fax line which I use with SpanDSP. I run Fedora Core 4. I have a problem that the third X100P does not answer the call. From the console I can see that there is an incoming call with the following: --

Problem: Flash on X100P does not flash. Phone line has Call Transfer. With this line plugged into a regular phone, it can receive a phone call. Then, depress the hook momentarily, release. Dialtone is now available. Dial a different number. Call is answered. Hook Flash again, now in a three way call. Hang up. The other two parties are still in communication. Now, plug same line into the X100P.