similar to: Dialplan question

Hi all, I am still confused about the way to use asterisk with QuickNet Phonejack. If I am not wrong, The phonejack card should be using the phone.conf as the asterisk channel. I was initially confused with the ZAP channel (The digium card), now that I have found out that Phonejack should use the Linux Telephony Devices and its configuration file is phone.conf, but the question is I do not know

Hello; we are looking to replace our current PBX with a *-box; it is connected to ONE ppp isdn connection that is terminated by the NC. We got on this box 4 msn's configured. currently we are working with pstn fxo's behind the PBX; it works but we can't use the CSID information behind it. We want to migrate and keep the MSN's to decide routing in combination with the CID.

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the

Hi, I have recently discovered the project along with the PhoneJacks produced by quicknet, they could be the answer to something I have been looking into. I would like to be able to test using a dial-in server & possibily also a Windows RAS server, however I only have 1 phone line. I was thinking that I create a setup like that illustrated below to solve the problem:- Ext 1000

I need help creating a channel for my phone device (Quicknet PhoneJack). I have installed and loaded the driver and phone devices listen in /dev (phone0 - phone15). [phone.conf] mode=dialtone format=slinear device => /dev/phone0 fxoks=2 ;Quicknet PhoneJack [extensions.conf] ... exten=>_NXXNXXXXXX,1,Dial,Phone/phone0 ... When I try to make a call, I get the following output: Executing

Recently, there're some posts about registration problems with this gateway. These are my observations using the latest firmware version 107a. a) The gateway will register all 4 ports if you're not using password. b) If using password, the gateway will only register the 1st port correctly. For the record, the 2-port 3502 doesn't exhibit this behavior. FYI.

Hi Friends, I am new to linux and new to asterisk. I need some help setting up asterisk in my linux box. Does anyone have a step by step guide ? On my PC i have installed a phonejack (from Quicknet) as well. Your help is appreciated.. I kind lost.. thanks, _________________________________________________________________ Expand your wine savvy — and get some great new recipes — at MSN Wine.

Hi list, I have some problems to get the QuickNet Internet PhoneJack working. What .conf files do I have to edit to get a dialtone for the first test with the standard configs from asterisk? I have the ixj driver running and a cat /proc/ixj after asterisk start tells me one reader and one writer. But if I pick up the receiver I don't get a dialtone nor I'm able to dial a number.

Sorry, if this question has been asked before. I have redhat 9 and asterisk installed. I would like to know how can i make work the phonejack with asterisk.

Hi, I am a newbie in asterisk, i could compile it and run it with no problem on a RedHat 9. In the same box, i got a linejack and a phonejack cards and i downloaded the CVS driver from quicknet. This 2 card were working in a openh323 (openphone and pstn) project with gnugk on a RedHat 9. I am using the default samples, and i tried /dev/phone0 and /dev/phone1, but when i run asterisk, i get this

Perhaps this will help... I have a phone connected to a QuickNet PhoneJack card. When I pick it up, I get a dial tone. When I dial a certain number of digits, the call is processed by Asterisk. The question: How does Asterisk determine how many numbers to let me dial? I'm banging my head against the desk here... _9XXXXXXX lets me make an outbound call, but _9X. only lets me dial 9 plus

How will this fare? I am planning on putting an asterisk box for my brother in the Philippines but they only have dialup internet. I want them to be able to use a telephone set on a phonejack or linejack card and call me and vice versa via VOIP. My setup in the US is working already with a broadband cable connection. I am thinking that dialup may not work because of the bandwidth required

Hello all, I'am trying to use 2 gnophones on my LAN. But I can't get any sound. Here is my configuration: 1. on PC1, I have: - Asterisk compiled from CVS (CVS-05/15/03) and it runs. - Gnophone binary version from Debian: 0.2.4+cvs.20020624-3 - a sound card working ( module es1371 for /dev/dsp) - I registered it as "alice" in extensions.conf 2. on PC2, I

Anyone knows where can I find spandsp? Official site seems permanently down... TIA, Simone.

I have a linejack and a phone jack in my asterisk server working well between the SIP phones and the phonejack. what I cannot get to work is the outbound linejack Phone/phone0 trunk line? how can I get a SIP or Phone/phone1 phonejack phone to dial 9 then outside number and pickup Phone/phone0 and dial it? right now it accepts a 95551212 but busy's on the last digit 2. no outside dial.

Hi, When I compile * with just make I get problems, I can't ring the phonejack PCI I have installed but when I compile with make valgrind I don't have problems ringing the PhoneJack. Anyone has been through this? Maybe that's a Dev list question, anyone on that list could please forward it to them? Cheers, -P -- __________________________________________________________ Sign-up

Hello all, New to the list, Asterisk and this wonderful world of convergence. From reading the docs, list and websites I hopefully correctly understand that I can use a plain cheap isdn4linux supported ISDN (passive) TA to hook up the PC to the ISDN line from the telco (FXO card?). Next in the PC I also need a FXS card like a Digium TDM10B or PhoneJack so I can hook up an analog phone to it. In

Hi, all. I'm making my first foray into AEL. I'm starting with a simple macro, but I've already encountered an odd behaviour. I'm wondering if someone can shed some insight: Asterisk 1.2.9.1 macro newPlaceCallPSTN { s => { TIMEOUT(absolute)=7200; NoOp(Analog Out List: ${ANALOGOUT}); ChanIsAvail(${ANALOGOUT}); NoOp(Available Out List:

Being very new to Asterisk, I'm not quite sure I know what I'm doing, and would appreciate some help. What I have so far: Quicknet PhoneJack card Asterisk Slackware 9.0 IAX protocol GSM libraries I have everything installed on my Slackware box (actually I have two of them and I want to set them up so that they can call each other) with an analog phone connected to the PhoneJack card.

The device is seen in linux pnp: isapnp: Scanning for PnP cards... isapnp: Card 'Quicknet Internet PhoneJACK' isapnp: 1 Plug & Play card detected total and I've installed the drivers from the openh323 dev... but I can't get * to see it. Does anyone have experience with this? THanks. -Dave. -------------- next part -------------- An HTML attachment was scrubbed... URL: