similar to: Configuring for outbound calls with PRI on T100P

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

In the next week or so, we'll be turning up a new T1 Pri from Cox Cable in Omaha using a T100P (installed but not yet configured). While discussing the interface parameters with a very knowledgable Cox engineer, we decided on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits of called number forwarded to *, and switchtype=national (NI2). They indicated their CO switch is a

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type

Hi List, a number of our customers are reporting dropped calls. here is the config. 1 T100P T1 Card 1 Asterisk (Mid Nov build) T1 is signalled as a PRI(National) The card will only sync up if we clock, if we line side clock the card goes into yellow alarm and won't sync up. the only errors we see are framing slips. Around 2500 slips over a 18 hour period. (this was reported from

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

Hi, I am getting this message on the * console on my first pri span. Pri show span show it is down, and I can't make any calls from the span. Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27

Due to some failed hardware on another platform, I've had to move a T100P card to a different chassis. After this move was completed, I am seeing some strange results on the T100P card that do not display to me any failure mode with which I am familiar. The card comes up, and shows "good" carrier and status, but Asterisk refuses to bring the D-channel up. Calls of course do

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

Dear Gurus, i am facing some unknown problem here.. first, let me describe my case. my office is using a nortel merridian option 11c PBX. and it is connected to the provider thru a E1 card, which is working fine with no problem. my plan it to slot in a server with 2 TE11XP card to intercept the outgoing calls. Provider <--te11xp---> asterisk <---te11xp------> nortel merridian

Hi, I've always used dahdi-genconf to just create the dahdi-channels.conf and since our PRI is fairly simple (just dump all the channels into one group) it works with dialing with dahdi/g1/(number). I'm trying to understand the file though for my own reference. It seems the file looks like this: group=0,11 context=from-pstn switchtype = national signalling = pri_cpe channel => 1-23

Hi Guys I'm configuring a TE212P card and have the following two entries in my /etc/asterisk/zapata.conf switchtype=dms100 signalling=pri_cpe When I reload asterisk I get the following messages: > -- Reloading module 'chan_zap.so' (Zapata Telephony) > == Parsing '/etc/asterisk/zapata.conf': Found > [Mar 30 17:48:42] WARNING[2985]: chan_zap.c:11072

Hello Group I have a Asterisk server running with 2 Digium T1 cards installed. 1 card connects to Telco via a PRI. The 2nd card is connected to a fax server via Digi DataFire RAS 24 PT1 Adapter (Digi0001). The idea is to have Asterisk route the calls based on DID or FAX tones. Everything is working great so far. The only problem is the Fax server does not see the DID. How can I tell if Asterisk

Hello, I'm using Asterisk (latest CVS head) to perform outbound call as robot/testing tool for an IVR platform, with a Wildcard T100P configure as ISDN Pri. For develop the exten context script I was using a real PSTN ISDN Megalink (DMS100) to reach the platform and my script was able to correctly detected the DTMF tone send back by the platform to synchronize the script. But for load test,

I did a cvs update this afternoon and since then asterisk doesn't seem to clean up the channels after they hangup. This has been working perfectly for quite some time previously... I do a show channels and it shows the channels still up. The only way out is to kill and restart asterisk.... I am frantically trying to would out how to get a non-current CVS copy of the source and get it back

A brandly new E400P 128 channel PRI, you can find more information on the Digium's site. The card was not used before, I sell it cause our company just don't need, we use Cisco AS5300. I can offer you the PCI PRI at $940 if bought in the next 2 days, I can send it to you via FedEx or DHL express. Please email me for more details! Regards, Kalin ----------------------------- IPPN Networks

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

Hi, I have two t100p cards installed. One card connected to the PSTN, the other card is hooked to the Definity PBX with a T1 cross over cable. The card connected to the PSTN works fine. The problem is with the card hooked up to the PBX. The light behind the card is green, but when I dial from this card I get an error. Its says it could start the D-Channel. Could someone help me out with this

I've been going back and forth with my telco for several days, trying different configurations to get a new PRI to come up. The bchannels are all up and the T1 is not in alarm status. The dchannel refuses to come up however. We've tried ni2, qsig, and now dms100 for the switchtype. The telco tech I've been working with says that he's been sending "reset all channels"

Does anyone know how to monitor * to see if they are receiving timing slips on a span connected to a T100P card? I am seeing b-channel restarts quite often and also getting "No D-channels available" warnings from time to time. Yesterday I had all the b-channels crash during a MeetMe Conference. Not good! This PRI is connected to an Avaya Definity PBX that is onsite and located in the