similar to: E1 yellow alarms

Hi! I have the chance to play with a couple of E400P cards, each installed in a IBM e330 XSeries servers (2 x 1GHz P-III CPU 2 Gb RAM, 36Gb SCSI HDD with RH8.0 2.4.18-smp kernel), and I'm trying to test/benchmark this e330/E400P combo generating calls thru /var/spool/asterisk/outgoing One e400P if doing the carrier work making calls and the other just receives the calls: Server#1

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Hi, After temporarily pulling the T1 cable out of our Asterisk box, we ended up getting a strange error messages even after the cable was plugged back in. [...] Dec 10 09:01:11 WARNING[1192437440]: File chan_zap.c, Line 5683 (zt_pri_error): PRI: Read on 63 failed: Unknown error 500 Dec 10 09:01:21 WARNING[1192437440]: File chan_zap.c, Line 5683 (zt_pri_error): PRI: Read on 63 failed: Unknown

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Good day eveyone, I'm hoping that someone can help me. Perhapps i'm overlooking the obvious, in truth, I hope that I am. I've scoured the mailing list and google, and haven't come up with much. I have a Digium T400P thats been connected to a channel bank for testing for some time now. all has been well. I've now just had

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. I'm getting the following error at random intervals on my TE410P with Asterisk CVS-03/30/04-11:49:01-CEST. I have two spans active, one connected to my Telco, the other to a Siemens PABX. Both spans display this behavior at random intervals. All calls are dropped when this happens. Spans are not necessarily in use when this happens.

Hi all: I have problems to setup my zaptel E100P hardware. When I start * after receive the "Asterisk Ready" I see this: *CLI> Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 1 Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 2 Up to channel 31. anfter this: Jun 22 20:37:55

Hello - I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I am not able to call the FXS extensions or get dialtone on them. The channel bank is connected via a T1 crossover to the cable and lights show green. I really need to get this functioning by end of day. If anyone can help me out I would be greatly appreciative. Thanks, Dave zaptel.conf loadzone =

Hi guys, I've been trying to get my ISDN-10 line up for the past few days, but its been going up and down. I am using OpenVox D110P card on asterisk version 1.4.21. It seems to me like a cable problem. I tried using Ethernet straight cable (12, 45, 36, 78) and also a "straight" cable where the twisted pairs are on 12, 34, 56 and 78. The problem remains the same.

This looks like a fun box... a Voip to Dect gateway, I've mailed them for pricing details.... < <http://www.computex.com.tw/news_archive_detail.asp?index=4053> http://www.computex.com.tw/news_archive_detail.asp?index=4053> Betel Consultancy Abelenlaan 19 T: +31 20 640 3018 1185 RT Amstelveen E: <mailto:info@betel.nl> info@betel.nl The Netherlands W:

Simple Q but I can't find the answer in the archives (and am too lazy to look in the source, but then its 32 Celcius here... Do all digium cards provide the zapata timing? e.g. also the analogs (including the X100P) or only the E1/T1 -ones or do I need to use ztdummy on the analog cards? Thanks, Michiel Betel Consultancy Abelenlaan 19 T: +31 20 640 3018 1185 RT Amstelveen

Hi all, I'm using asterisk CVS-08/14/03-22 on a box with a digium T1 connected to a channel bank and a digium E1 connected to the PSTN. I get occasional warnings from asterisk: WARNING[37909]: File chan_zap.c, Line 3197 (zt_read): zt_rec: Unknown error 500 This happens mosttimes in a loop like this: [netland_helpdesk] exten =>

Some switches provide the functionality to try a number till it becomes available. Thus when one dials a number and get a busy, one enters a *XX# code and the switch will call your extension when the called party becomes available. Has somebody already built this in/for Asterisk, otherwise I'll look into it. Michiel Betel Consultancy Abelenlaan 19 T: +31 20 640 3018 1185 RT

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

I need your help I have a sangoma A104D on my dell server; I got card status ok with no alarm If I dialed the extension 6210006, it shows the output as stated below, but there is no ringing from the pstn number nor the iax softphone am using on my pc. I will be glad if someone can give me a working config? What I want to achieve is to send all my call to the pstn on A104D? The pstn am

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

Hi all, Has anyone already written something which allows saving and loading the internal DB settings? All users CFWD and speeldial settings are stored in the DB in my setup which makes it a pain to restart Asterisk.... Looking at showtree in db.c (why isn't that exposed in the CLI?) It shouldn't be too difficult, but I don't want to reinvent the wheel. On the same track, I am also

I have configured TDMoE sucessfully and I am able to make a Zap connection from one box to the other. The question I have is.. I'm getting repeated errors every second on both systems.. Oct 3 09:53:16 WARNING[4409]: chan_zap.c:6252 handle_init_event: Detected alarm on channel 1: No Alarm Oct 3 09:53:16 WARNING[4409]: chan_zap.c:6252 handle_init_event: Detected alarm on channel 2: No Alarm

Hi All, For the most part, the PBX works as it should. Occasionally people complain that they call and the PBX doesn't pick up. Other times it looks like the call is answered by Asterisk but I still hear ringing and I start listening to the IVR menu a few seconds into it. As for Asterisk not picking up, I see the following in the logs: [Mar 27 13:32:29] NOTICE[13197]: chan_zap.c:7071

Guys.. I just saw this for the first time... I did some google and wiki without any luck.. what does a red or yellow alarm mean in zaptel? Feb 23 02:54:16 WARNING[16890]: chan_zap.c:5865 handle_init_event: Detected alarm on channel 2: Red Alarm Feb 23 02:54:24 NOTICE[16890]: chan_zap.c:5860 handle_init_event: Alarm cleared on channel 2 This just happened by itself..