similar to: Using asterisk with ISDN - How to configure

I am trying to get our Meditech application to work on a Mandrake 8.1 in GNOME. I am getting the following messages when I try to run it: The application runs, sort of. The screen is a complete mess. Warning: The Wine launcher is unable to find xmessage. The launcher script relies heavily on finding this tool, and without it, it will behave poorly. Most Linux distributions have one or

Hello, i have asterisk with 2 internal isdn cards - handled by isdn4linux and i need to setup whol system like this route some call beggins with 0 or 00 - long distance through first card, route calls to mobile network via second card ( tehere is isdn gsm gateway connected).how i can do this using only isdn4linux (/dev/ttyi) ? regards Marian -- SUNTEQ s. r. o. Bojnicka cesta 35 # Prievidza

Having ISDN FXOs and a bunch of ISDN DECT base stations, I went looking for a CAPI compatible active BRI adapter capable of NT mode. I have found that the 'Eicon Diva Server 4BRI' fulfills theses requirements. However, at EUR 1387 for four BRI interfaces, it does not come cheap. Are there other users of similar hardware that can point me to alternatives ?

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

I want to test asterisk with its DID functions on a smaller scale without the expense of a PRI. I am in the US, and want the most reliable/stable, and feature rich solution that I can have. What ISDN card would be reccommended? My clec switch operator says he can/will send DID info to my BRI's if I wish. Can Asterisk, or one of its addons support this? What BRI solution would be

I know this has come up before but... Has anyone done anything to get an IAX client built on Windows? I thought someone had started one, but I haven't heard anything about it since - and that was months ago? Anyone have any idea what the status is? -- Ron Gage - Saginaw, Michigan I am looking for work - resume at http://www.rongage.org/resume.doc Electrical Engineering, Linux Programming,

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway

This is my first posting to the list. Thus hopefully the question has not been asked several times before... I'm trying to install asterisk on a PC using Debian Sarge but without any real success... Problem: I may get the Asterisk packet (Debian version) installed using 'apt-get install asterisk', but that does not include the bristuff from Junghanns

anyone has idea what problem can be here, something with codec but i have today CVS version and grandstream phone with 1.5.0 firmware.I try to change codec in phone and also in asterisk-sip.conf but the same. What can be problem ? tnx, Tomaz *CLI> -- Executing Dial("SIP/102-767c", "CAPI/2:5") in new stack -- Called 2:5 -- CAPI[contr1/2003002]/0 is making

I'm currently using the SJPhone softphone with asterisk for remote SIP. When I dial into the voicemail, and attempt to pass the extension, I "hear" the sounds, but asterisk is not receiving any DTMF signals. If I use the Estera softphone, asterisk does receive the DTMF signals. Normally, I'd just say "Use the Estera" softphone to myself, but that's not an option,

Hi All, First of all, please no flames about the footer of this message. It's being inserted into all outgoing email by the server here without asking me personally first once I send out email. Since I've been very interested in setting up an Asterisk PBX + IVR + Voicemail system to support a small business and a foundation for quite some time now, in order to replace their current ISDN

hello! I'd like to use my asterisk-box on a p2p-line from my alcatel pbx. isdn4linux and capi works fine on a s0-line from the pbx, but i need more then 8 msns, cause i'd like to implement a voice-mail system and an extension to our "old" pbx with voip-phones. had anyone success using isdn4linux on a t0 (p2p) line (of course with an inexpensive passive card like my avm

Hello, I am trying to install a Billion ISDN on Asterisk I have Debian Etch and I installed theese packages: apt-get install linux-headers-`uname -r` apt-get install make apt-get install ncurses-base ncurses-bin ncurses-term apt-get install libncurses5 libncurses5-dev apt-get install bison apt-get install openssl apt-get install libssl0.9.8 apt-get install libssl-dev apt-get install

Tried update on wine (7/9/2009, appx 20:15 EDT). Needed wine-core added to my includepkgs. Did and looked like it would go until this. --> Finished Dependency Resolution Error: Missing Dependency: /usr/bin/xmessage is needed by package wine-core [root at wlmlfs08 etc]# yum provides xmessage Loading "protectbase" plugin Loading "fastestmirror" plugin

Hello all. Since half december we are trying to implement * as our primary PBX. We had a test machine running with 2 sip phones and a single ISDN card. Since this was working ok, we installed * on our main Debian server. Some specs: P4 2.8 Ghz HyperThreading 512 MB RAM Debian Sid updated every week. Linux 2.6.9 vanilla kernel (not the debian package) 1 Intel Pro 100 nic for internal network 2

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

Hi Alessio Yes, the problems you report do seem similar to the issues I had. I found on the Dells that the audio prompts were very choppy and played slower than normal. Occasionally there would be 'bursts' oav a second or so of 'good' audio. I also suspected IRQ issues but the Dell Mobos had no way of adjusting them. Best thing is to try and get the card on its own unshared

Hi, my setup is quite simple: an asterix CVS of 2003-11-15 on a 2.4.21-debian-5 GNU/Linux box in an internal network (192.168.1.0/24, asterisk is 192.168.1.10). - with a SIP phone configured as 192.168.1.190, and with its SIP server being 192.168.1.190 - with an ISDN AVM c4 i4l card on an ISDN connection with 2 channels. I try to: - dial-in from ISDN, then transfer to the SIP