similar to: Asterisk 1.2.11, Asterisk-Addons 1.2.4 and Zaptel 1.2.8 Released

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Hi, I've been able to make make install the Zaptel drivers (1.2). I'm using a b410p so I executed the following command make b410p. I tried this on multiple machines, but it always failes: root@asterisk:/usr/src/zaptel-1.2.11# make b410p [ -f misdn-b410p.tar.bz ] || wget ftp://ftp.digium.com/pub/zaptel/b410p/misdn-b410p.tar.gz --23:59:54--

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

Just to add.... P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] Sending :160 bytes 2 MISDN P[ 0] misdn_jb_fill: written:160 | Buffer status:256 p:861fee0 P[ 0] misdn_jb_empty: read:128 | Buffer status:128 p:861fee0 P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] PH_CONTROL: channel:1 oad2:07nnnnnnnnn dad0:820055 P[ 1] --> DTMF

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

Hi, I'm using a 4-port BRI card (b410p) to make and receive calls (via chan_misdn): http://www.digium.com/en/products/digital/b410p.php This card supposedly has hardware echo cancellation. How can I check that echo cancellation is actually ON (taps, etc) on a given misdn channel (like with the "zap show channel X" command). "misdn show channel X" doesn't seem to show

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, We have a BRI installation who is experiencing constant echo with the Digium b410p and mISDN. I have adjusted gains, and originally thought that the desktop phones were at fault, although we experience the same problem when a call is bridged out to an external number. I've tried it with 128 taps (the default and I believe the supported

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

I have used the b410p card with Asterisk 1.12 quite successfully. I now want to get the card to work with Asterisk 1.4.0beta3. It however can't seem to get chan_misdn compiled. In menuselect, chan_misdn has this: Depends on: isdnnet, misdn, suppserv Can anyone help? -- thanks, yusuf -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to

Hi all, I'm trying to get a digium B410P to work with asterisk 1.6.0.1 (but i have the same problems with asterisk 1.6.0) Official digium documentation cover up to asterisk 1.4.x and suggest to use zaphfc... but as i understood zap is completely gone in 1.6 I tried with misdn (1.1.8, 1.1.7.2 and 1.1.5) and card is recognized correctly by the kernel but chan_misdn does not work as expected.

Hi list, we have a dual Xeon server with 2GB RAM running Debian Etch 2.6.18.4-686 kernel. The server has 2 B410P cards plugged in. No other card. We installed Asterisk 1.4 trunk with zaptel trunk, ran make b410p, the install mISDN1.1.0 (for bug 9064) configure and compile Asterisk with chan_misdn, all is fine. In misdn-init.conf we have added option=1,master_clock. Asterisk is up and

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

I have the same problem as the following: http://threebit.net/mail-archive/asterisk-users/msg36602.html I am using a b410p (Wildcard) in TE mode on 4 channels of ISDN2e and it totally fails to detect incoming DTMF. The newer mISDN drivers have a parameter "dtmfthreshold" where you can tune the volume above which DTMF detection is initiated. However (I've tried it) the newest

Hi List, I?m having problems compiling chan_misdn: asterisk:/usr/src/chan_misdn-beta-0.0.3-rc4 # make install cc -ggdb -Wall -D_GNU_SOURCE -Wno-missing-prototypes -Wno-missing-declarations -fPIC -I/usr/src/asterisk/include -DAST_CONFIG_DIR=\"/etc/asterisk/\" -I/usr/src/mISDNuser/include -I/usr/src/linux-2.6/include -I/usr/src/mISDNuser/i4lnet/ -Wall -c -o chan_misdn.o chan_misdn.c

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Not being able to build mISDN on Ubuntu using "make b410p" I have used mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version of mISDN to work ok with these cards? Or is there a way to build using "make b410P" on Ubuntu? (make force does not help at all) 2) In some of our installations

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Hi i am experiencing some problem with asterisk and misdn i've patched and recompiled the 2.6.15.5 kernel on the server i use a BN8S0 card with alla channels in TE mode. i can load hfcmulti and mISDN_dsp i load this with: /sbin/modprobe hfcmulti layermask=0xf protocol=0x22 type=0x08 and then /sbin/modprobe mISDN_dsp dmesg returns me the following: Modular ISDN Stack core $Revision: 1.34