similar to: CentOS x64 crashed

I have a couple of 64-Bit Xeon's with CentOS 4.2 x86_64 installed on them. They don't all have the same motherboards. I've having a difficult time getting CentOS 4.2 x86_64 to boot on some of them in SMP mode (UP works fine). After the installation of CD, it boots up but kernel panics with the following error: Badness in i8042_panic_blink at drivers/input/serio/i8042.c:992 This is

I attempted an upgrade of our production system from Asterisk/Zaptel 1.2 to 1.4 this weekend. Intially everything looked like it was working properly, but some time in the day following the upgrade, the system died to a kernel panic. I wasn't able to catch the entire kernel dump on the console unfortunately. I attempted to isolate the panic, and found that when 'service zaptel stop'

Is there a way to determine what package changed from CentOS 4.1 to 4.2 (or between any two versions)? I need to create a yum repository to upgrade some machines that cannot talk to the Internet. Thanks for any help. ID:FONGVANG

What exactly is different between the 32 and 64-bit version of CentOS 4.2? The kernel (drivers, file system, etc.) is probably compiled to support 64-bit and probably glibc. What're some important differences between the 32 and 64-bit version? I'm just trying to get a deeper understanding. Thanks in advance for any help. FongVang

hi, my PCI-Express device is generating interrupts at a very high rate. when i generate legacy interrupts the system hangs saying "Badness in i8042_panic_blink in drivers/input/serio/i8042.c:992" but when i generate the interrupts using the MSI mode. the system is working fine. please help --------------------------------- Here?s a new way to find what

Hi There, we have a problem with a fresh installation of gluster 3.11 on a ubuntu 16.04 server. we have made the installaton straight forward like it ist described on the gluster.org website. <http://gluster.readthedocs.io/en/latest/Install-Guide/Configure/> in fstab is: /dev/sdb1 /gluster xfs defaults 0 0 knoten5:/gv0 /glusterfs glusterfs defaults,_netdev,acl,selinux 0 0 after

Hello, I am using CentOS 4.6 (2.6.9-67.plus.c4) on a toshiba tecra 8000 notebook. If closing the panel, "Panel Power On/Off" is enabled in bios, the notebook does suspend. But after opening the panel, the notebook completely freezes. If the suspend only takes a few minutes, then everything is working fine. But if the suspend takes a time more than five or ten minutes, the system

In our environment, we have a mixture of 32 and 64 bit systems. Would the 64-bit CentOS flavor work 32 bit systems? What kind of impact would this have on performance if the 64-bit OS on 32-bit hardware?

In CentOS 4.1/2, what package contains this library: libstdc++-libc6.2-2.so.3? I installed a couple of the compat- packages, but this library is still missing.

I read that XFS has problems with 4K Stack size for Linux on 32-bit systems. How did we address this in the centosplus kernel? Since what release of CentOS was this problem resolved? Is there a quick way to know what size the Linux stack is configured to be in a system's that's running? Thanks for your help. -------------- next part -------------- An HTML attachment was scrubbed...

Hello, I just went back to 2.4.9-ac18 from 2.4.10 (i386), and then for the first time migrated all my ext2 partitions to ext3. I did this over a series of reboots, as I confirmed that indeed things continued to work. The last step I took was to convert /. I have set up /etc/fstab to mount my 'ext3' partitions with 'auto', I suppose thinking this will make it easier to roll

I'm getting a couple of systems that are arriving with the new 3ware 9550sx controller. Does anyone know when this will be natively supported by CentOS? Has anyone built an RPM of the driver/module for this new controller?

3ware now provides driver disk for CentOS. A couple of months ago, I had to add support for the 3ware 9550sx. The driver disk provided for CentOS 4.1 work perfectly. I now need to add support for the 3ware 9550sx for CentOS 4.3 x64. Although the driver disk is available, it doesn't seem to work. Anaconda just can't find the 3w-9xxx module. This is the same seutp as CentOS 4.1 (which

At the beginning of August, Mikulas Patocka posted to linux-kernel mailing list about adding snapshot merging to LVM[1]. Basicaly, snapshot merging means that it is possible to turn a snapshot back into its origin. Using LVM, however, means that you need to have free place outside of the filesystem (i.e., in physical volume) to make snapshots, which is not always possible on workstations and

I downloaded the src rpm for CentOS 5 and tried to recompile it. It failed with the following message: + sh ./scripts/modsign/modsign.sh /var/tmp/kernel-2.6.18-8.el5-root /lib/modules/2.6.18-8.el5PAE/kernel/drivers/char/watchdog/pcwd_pci.ko CentOS gpg: WARNING: unsafe permissions on homedir `..' + mv -f

For some reason, CentOS 4.1 waits approximately 3-5 min at the "Determining host name and domain" during kickstart. RedHat 7.1, RedHat 9.0, RedHat Enterprise 3.0, and even CentOS 4.0 do not have this problem using the same kickstart server (my kickstart server is configured to kick all of them). Does anyone know why CentOS 4.1 is particularly slow at this stage of kickstart? Thanks

The xfs kernel modules at dev.centos.org are very handy. There are a couple of xfs modules in the 4.3 x86_64 directory, but I don't think it's for the x86_64 4.3 kernel (2.6.9-34). The latest ones in that directory is for the -22 kernel (I believe this came with CentOS 4.2).

For over five years now, we use Perl during the post install of kickstart to perform customization. It appears the Perl setup is broken in CentOS 4.3 x86_64. It still works fine on CentOS 4.1 32-bit. The library Perl needs is missing: # perl -V error while loading shared libraries: libperl.so: cannot open shared object file: No such file or director Is this a bug or is RedHat deprecating

What's the easiest way to disable a kernel module during kickstart? Is there a syslinux command that could be passed in to prevent a module from loading? TIA!

Hello, please help me: After searching for nearly 2 weeks for a solution, I have to ask for assistance: System: debian sarge - update from an working installaton on woody (without printing) Now the samba server joins ADS, authenticates users, but should also provide printers. I have installed cups, configured my smb.conf: --------------------------------- [global] load printers = yes