similar to: drive size limit for syslinux [solved]

I was working on making a 40gb laptop ide drive bootable via syslinux as the drive is in an external hd enclosure. syslinux installed on a 100 mb bootable fat32 partition and when I tried to boot from the drive, I got a syslinux prompt which was correct as I had not done a config file yet. I later found a 60GB laptop ide drive and put the larger drive in the enclosure and tried to install

I have a 40GB IDE laptop hard drive I took out of a dead laptop and I was hoping to put some good use to it. The drive is inside a USB drive enclosure and I carry it in my laptop bag. Its not big enough to be a backup drive, and generally too big to BIOS boot from. The chipset on the enclosure is from Prolific and registers as a "Mass Storage Device" I haven't had good luck with

I've begun working on a syslinux project with a portable usb drive. Up to this point I was a pxelinux.0 user only. My virtualmachine system (Oracle VirtualBox) can netboot so testing config file changes was no big deal. VBox is currently unable to boot from a usb drive despite documentation that says it is possible. Is there a windows based tool that can scan and test a syslinux

Hi all, Space is starting to get a bit tight here, so I''m looking at adding a couple of TB to my home server. I''m considering external USB or FireWire attached drive enclosures. Cost is a real issue, but I also want the data to be managed by ZFS--so enclosures without a JBOD option have been disgarded (i.e., I don''t want to use any internal HW RAID controllers). One

Hello, Is there a way to touch Shoutcast directory with an Icecast server ? Is for a mp3 stream. The server is already serving ogg stream but our foundation got a new member that did not know about ogg, and he needs time to encode his tracks to ogg, and then we should temporarily relay his mp3 stream, but we want to be dired by SC directory ... How to ? :-) -- ASPO Infog?rance

I have 15x SAS drives in a Dell MD1000 enclosure, attached to an LSI 9200-16e. This has been working well. The system is boothing off of internal drives, on a Dell SAS 6ir. I just tried to add a second storage enclosure, with 15 more SAS drives, and I got a lockup during Loading Kernel. I got the same results, whether I daisy chained the enclosures, or plugged them both directly into the LSI

Hello, The message you posted to the List below contained file enclosure data and consequently was not posted to the List. You will notice that the enclosure is quite large and contains data that many mailer programs can't use. This enclosure also adds far too much 'useless' data to the already huge archive file. If you wish to share files such as photos of your project with the

Hello Everyone, I have a CentOS 6.3 host running a few KVMs. One of them is a CentOS 6.3 KVM that I want to use for making backups with BackupPC. What I'm having a problem with is assigning the KVM an external drive. I used to run BackupPC on an Ubuntu box. The backups went to an external eSATA 1.5TB, ext4 format, single partition drive (regular 3.5" in an enclosure). I want to now

My apologies if this is a bit off topic... I am going to start doing backups to removable hard drives and I will need to send these hard drives to an off-site storage facility. I am looking for some way to protect the drives after I pull them out of the system. I was hoping to find some kind of clamshell enclosure similar to what is used with external hard drives, but so far I haven't found

The serial port install has almost gone by the wayside, yet I still find a number of cases where it would be great if there were such a thing. Headless servers come to mind specifically. Grub legacy has a way to setup the serial port and broadcast output to both the console and the serial port to check to see where the real person is. I'd like to know if syslinux can do this as well. Id

HI All, I have a dilemma and I would appreciate advice 1. Get a good size case, mobo, processor, etc and put 8 hard drives it in and RAID them. (yes an 8 port SATA mobo). Running CentOS. or 2. Get an eSATA enclosure that has room for 8 or 10 drives and just connect it to box? I know that RAID is not a full proof backup, but I am looking for a solution to store all of my data, projects, music,

I recently purchased an I/O Magic USB enclosure for 3.5" IDE hard drive. Has anyone else used one of these? It works fine with Windows, except of course that Windows can't read the ext2 partitions on the disk I put into the enclosure. CentOS4 can't find the device, much less access the drive -- it doesn't show up in "lsusb" output, although the active light on the

On Jan 12, 2018, at 3:18 PM, david <david at daku.org> wrote: > > Or is it related to the annoying spin-down and spin-up delay of external USB disks. More likely, crap hardware, which is awfully hard to avoid in USB-land. Just the other day, I traced a machine that failed to reboot to an external USB disk. Unplug it, machine boots right up. Move the same disk to a machine as

Hello, Is it possible to have one password per source with Icecast 2.2.x ? How to ? -- ASPO Infog?rance http://aspo.rktmb.org/activites/infogerance Unofficial FAQ fcolc http://faq.fcolc.eu.org/ LUG sur Orl?ans et alentours (France). T?l : 02 34 08 26 04 / 06 33 26 13 14

Warren Thanks for the thoughts. Even with 'dmesg', I found nothing. The reboot got rid of the problem and it continues to run perfectly in the same configuration. I, too, have a slight dislike for external USB disks, and much prefer internal drives for esveral reasons: - Internal drives are protected by being inside a tower and thus have less chance of falling or being bumped than

I am building three identical systems. Well they will have different host names, and with time the software setups will drift. But at install time they are identical. Is there some way, (with dd I might guess) to do a hardare level copy? All three drives are Hitachi DK23DA-40F (40Gb). Supposedly factory reconditioned (they are in sealed bags with a drive sticker stating: "Refurbished

̨ʤÏòÄãÎʺÃ! ÎÒ¹«Ë¾³¤ÆÚ´Óʹú¼ÊóÒ×,ΪÍÚ¾òÊг¡Ç±Á¦¡¢À©´ó¾­Óª¹æÄ£,ÒâÔÚ¹óµØ Ñ°ÕÒÁôÒ×´°¿Ú,Ìؽ«´Ë¼Ûͬ±í³Ê¹óµ¥Î»²Î¿¼.ÎÒ˾ÌṩһÁ÷Æ·ÖÊ,Ò»Á÷·þÎñ,ËÍ»õÉÏÃÅ, »õµ½¸¶¿î, ÅúÁí¾ù¿É.»¶Ó­¸÷½çÅóÓÑÀ´µç´¹Ñ¯¼°Ö§³Ö.¶àл!!! ̨ʤ¹«Ë¾ ÖйúITóÒײ¿ :ÇØ Áú ͼ ÇëÎðÖ±½Ó»Ø¸´£¬ÓÐÒâÕßÇëÀ´µç ------0139-59726696 Ò»:±Ê¼Ç±¾µçÄÔ(È«ÇòÁª±£µ¥,ÈýÄê) ±Ê¼Ç±¾µçÄÔÊÖ»úÉÏÍøרÓÃPC¿¨----------1450Ôª A . Ë÷Äá SONY SR/27K(4500Ôª)

̨ÕýÏòÄãÎʺÃ! ÎÒ¹«Ë¾³¤ÆÚ´Óʹú¼ÊóÒ×,ΪÍÚ¾òÊг¡Ç±Á¦¡¢À©´ó¾­Óª¹æÄ£,ÒâÔÚ¹óµØ Ñ°ÕÒÁôÒ×´°¿Ú,Ìؽ«´Ë¼Ûͬ±í³Ê¹óµ¥Î»²Î¿¼.ÎÒ˾ÌṩһÁ÷Æ·ÖÊ,Ò»Á÷·þÎñ,ËÍ»õÉÏÃÅ, »õµ½¸¶¿î, ÅúÁí¾ù¿É.»¶Ó­¸÷½çÅóÓÑÀ´µç´¹Ñ¯¼°Ö§³Ö.¶àл!!! ̨ÍåÕýÈÙ¹ú¼ÊóÒ×¹«Ë¾ ÖйúITóÒײ¿ :Áø½ðÃú ÇëÎðÖ±½Ó»Ø¸´£¬ÓÐÒâÕßÇëÀ´µç ------0138-50738839 Ò».µçÄÔÅä¼þ(RMB.Ôª): A:Ö÷°å: ΢ÐÇ 845Pro2-LE(Socket,i845,SDRAM,AC97Éù¿¨)---530 845Pro

I'm trying to learn Asterisk (specifically Trixbox) and, as you probably know, it runs on CentOS. I want to run it on my laptop and thought that I could install it to an external USB hard drive, like I've done with Fedora 12 and Linux Mint 8 (I like to keep my small CentOS/Windows dual booting hard drive in the laptop's hard drive slot). But it won't work. It kept giving me hard

In this case the environment contains the variables local to the function, and its enclosure is the environment of the enclosing function.(R-lang:p11) I want to know if the "enclosing function" means the closure of the function? for example ,if I call function mean(),and the create an environment,say e1,then the enclosure of e1 is the namespace of base package? Right? Thank you!