similar to: Recall: sanboot.c32

Hello All. Yesterday I?m trying another ways but without luck. Issue still exist ? Please help. Is it possible to rewrite DHCP setting for sanboot.c32 after gpxelinux.0 load? Will be nice to have this possibility because: 1. DHCP can be ?black box?. 2. DHCP admin not available. 3. PXE server rewrite dhcp setting. I cannot boot from cdrom after pxe(gpxelinux.0) ? please help. LABEL Windows 7

Hello Anvin. Thanks a lot for you respond. But it`s not help. I get error : netconn_write failed: -5 even if I use ip address. http://10.5.9.127/.... Looks like HTTP protocol is not working. Is it possible to get debug version ? Thanks. Vladimir Izmalkov T +38 044 490 33 93 ext. 240 M +38?091?354 03 73 IT Home From: H. Peter Anvin [mailto:hpa at zytor.com] Sent: Monday, September 02,

Hi, I have a working PXE environment that chainloads gPXE and loads pxelinux.0 afterwards. As I'm also interested in doing san boot (in my case aoe) I tried loading the new gpxelinux.0 file instead of my gPXE --> pxelinux.0 setup (works) and booting from my aoe target by adding this to the default config file: LABEL doaoe MENU LABEL Continue AoE kernel sanboot.c32 append

Hi, I've been trying a couple of day now, but I can't seem to figure it out. On www.etherboot.org, I found the example of configuring gPXE so that it mounts an iSCSI lun and then boot from CDROM so you are able to install on the LUN. But if I use gpxelinux.0 (latest release 3.73), with sanboot.c32 like this: label sanboot2008srv menu label ^[iscsi] Windows server 2008 kernel

Hello All. I need make one configuration for many PXE servers. All of them has different IP`s. Will be best is somehow in menu will be possible to have environment variable with server ip. Example: Pxelinux.cfg\Default UI vesamenu.c32 MENU INCLUDE pxelinux.cfg/graphics.conf MENU INCLUDE pxelinux.cfg/server.menu .. Skip .. label default MENU LABEL ^Custom ISO COM32 cmd.c32

Try using lpxelinux.0. "Izmalkov, Vladimir" <vladimir.izmalkov at sap.com> wrote: > >Hello All. > >I `m trying migrate to version 6.01 from 5.01 and without luck. >I`m still on 5.01 and I use gpxelinuxk.0 5.01 but I rename it to >pxelinux.0 >my pxelinux.cfg/default >label default > MENU LABEL ^Custom PE > KERNEL

Hello All. I `m trying migrate to version 6.01 from 5.01 and without luck. I`m still on 5.01 and I use gpxelinuxk.0 5.01 but I rename it to pxelinux.0 my pxelinux.cfg/default label default MENU LABEL ^Custom PE KERNEL http://deployment/sources/common/pxe/memdisk APPEND iso raw initrd

Hello All. I have few networks with Tivoli Provision Manager (http://www.ibm.com/developerworks/downloads/tiv/pmfos/?S_TACT=105AGX28&S_CMP=TRIALS ), Altiris (http://www.symantec.com/business/deployment-solution) and WDS (on W2008Stdx32). I successfully expand WDS functionally with pxelinux (4.03).I really like how pxelinux working. Server who respond on client request is on Windows 2008

Op 2013-09-05 om 07:18 schreef Izmalkov, Vladimir: > From: H. Peter Anvin, Sent: Monday, September 02, 2013 5:20 PM > > "Izmalkov, Vladimir" <vladimir.izmalkov at sap.com> wrote: > > > Hello All. > > > > > > I `m trying migrate to version 6.01 from 5.01 and without luck. > > > I`m still on 5.01 and I use gpxelinuxk.0 5.01 but I rename

On Sun, Sep 20, 2015 at 8:33 AM, syslinux-bot for Gene Cumm <gene.cumm at gmail.com> wrote: > Commit-ID: e0ac1d2fdf7d7c58457f3796a12561cce95ca29f > Gitweb: http://www.syslinux.org/commit/e0ac1d2fdf7d7c58457f3796a12561cce95ca29f > Author: Gene Cumm <gene.cumm at gmail.com> > AuthorDate: Sun, 20 Sep 2015 08:30:55 -0400 > Committer: Gene Cumm <gene.cumm at

Trivial module to execute an arbitrary command. --- com32/modules/Makefile | 2 +- com32/modules/cmd.c | 42 ++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+), 1 deletions(-) create mode 100644 com32/modules/cmd.c diff --git a/com32/modules/Makefile b/com32/modules/Makefile index 2739a39..930e89b 100644 --- a/com32/modules/Makefile +++ b/com32/modules/Makefile

Hi Bootmeisters, I am using gpxelinux.0 + sanboot.c32 to boot a diskless machine into Linux. I would like to use device-mapper-multipath to provide fault tolerant access to its root disk. Although I am able to do this by hardcoding the additional paths in the initrd, it would be better if the bootloader could pass the information in the iBFT (iSCSI Boot Firmware Table). However, at the

Applies to Syslinux 4.06. Attached, below, and available at: Repository: git://git.zytor.com/users/sha0/syslinux.git Branch: nictype - Shao Miller ----- From 2764e260e12d9769e3b699e4213b9a164e64924a Mon Sep 17 00:00:00 2001 From: Shao Miller <sha0.miller at gmail.com> Date: Thu, 22 Nov 2012 20:43:25 -0500 Subject: [PATCH] nictype.c32: PXELINUX module to display UNDI NIC bus

I wrote a new module "whichsys.c32" which detemines which command to execute, based on the Syslinux bootloader variant. In the near future it should/can be replaced by a lua script. But for people who want small binaries: whichsys.c32 is +/- eighty times smaller than lua.c32, atm. Usage: whichsys.c32 [-iso- command] [-pxe- command] [-sys- command] Examples: whichsys.c32 -iso-

Applies to Syslinux 5.00-pre9. Attached, below, and available at: Repository: git://git.zytor.com/users/sha0/syslinux.git Branch: hexdump - Shao Miller From c9c67dd61ba0b11e46d514601cf0722e1b43017c Mon Sep 17 00:00:00 2001 From: Shao Miller <sha0.miller at gmail.com> Date: Sun, 4 Nov 2012 00:26:32 -0400 Subject: [PATCH] hexdump.c32: Simple file hex-dumper Usage: %s

I'm currently trying to integrate ReactOS's bootloader into my concept bootdisk with standard layout. It uses Syslinux 4.10pre15. This is failing on two parts: 1) bootsector method only works if specifying huge cluster size (16KB) 2) Multiboot method fails due to opening bootloader's configuration file from harddisk instead of bootdisk.

Hello, today I upgraded from Syslinux 4.06 to to Syslinux 5.00. But now the system won't boot anymore and I get the message Failed to load ldlinux.c32 Boot failed: please change disks and press a key to continue What I have done: 1) Installed Syslinux 5.00 2) Reinstalled "mbr.bin" to /dev/sda and /dev/sdb using dd bs=440 count=1 conv=notrunc

I have a working pxelinux environment. I point the "boot server" (windows dhcp) to my tftp server and "Bootfile name" to pxelinux. How would I invoke the chain loader over iscsi? I was reading the following page and wondering if I could use gpxelinux to boot this? http://etherboot.org/wiki/soc/2009/dverkamp/notes/windows_xp_iscsi I saw examples of san boot here

I'm having issues with the ifcpu[64].c32 modules. I am building a menu system (as opposed to the command line only options I was previously using) to make it easier for my boss to use PXE. I discovered the modules for auto detecting the CPU and thought hey, that's great! However, I'm having an issue where when I select to boot say System Rescue CD, it drops me to the command line

On Mon, Sep 21, 2015 at 6:23 PM, Alan Sparks via Syslinux <syslinux at zytor.com> wrote: > If this is asked before, please point me at the answer, can't find it... I seem to recall seeing this before. > With pxelinux 3.8.6 (or, < 5.x), I was able to chain boot pxelinux.0 > from ipxe, having set appropriate values for DHCP options 210 and 209 > for the remote file path