similar to: PXEboot trouble with Soekris 4826

Hi All, I am still having troubling with PXE. Thanks for replying Shao.I did follow ur suggestions and my results have improved a bit.From Ethereal and TCPdump, I can see that the client sucessfully dowloads the file pxelinux.0 from the server but stops at this point. here is the output of tcpdump tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 96 bytes 11:05:41.966864 IP

hi Peter, everyone, I recently installed extlinux on my CF drive. after a few botches, it works, with menu.c32 too. Heres a few notes/observations: - menuing seems pretty sensitive to presence of tabs in extlinux.conf, unlike with pxelinux.cfg/default, Is this an oversight, or something Im misremembering ? - extlinux doesnt have the timeout after menu-choice. if I dont choose, it times out and

I''m trying to work through the procedure for installing Flashboot for the first time. This Soekris has no removable CF, so I''m using PXEboot to start the standard 5.2 bsd.rd kernel and then see if I could noodle my way through it. I formatted the disk with newfs (specifically, I formatted the "a" partition on the disk), copied the "boot" program over, then

hpa, etal, pxelinux works great from a push of the reset button. machine boots normally. However, after i issue 'reboot' command, my box fails to find the tftp server during reboot. This looks to be happening before pxelinux has any chance to participate, so it cannot be to blame. Im seeking corroboration here before I go badgering the bios-provider here's the relevant

I have released SYSLINUX 3.08-pre5. Sparse files should now work correctly in extlinux. Symlink support still needs to be added, though. -hpa

hi HPA, in case youre collecting such bugs, heres what (I think) I know. sorry for the excessive/pedantic detail.. this PXE code NSC DP83815/DP83816 Fast Ethernet UNDI, v1.03 Copyright (C) 2002, 2003 National Semiconductor Corporation All rights reserved. Pre-boot eXecution Environment PXE-2.0 (build 082) Copyright (C) 1997-2000 Intel Corporation has a

Hello, I have a Soekris net4501, which I'm PXE booting using pxelinux. Everything seems to be working splendidly, except for the fact that I can't seem to make pxelinux understand use the net4501's serial console port correctly. The net4501 uses the serial console as its primary interface; I'm using a null modem cable and minicom to operate with it. At boot, its startup

Hello, I mentioned back with version RC8 that dovecot was having an issue with the first login working, but all subsequent attempts failing with the error message: "Error: Maximum number of mail processes exceeded" in the dovecot log file. This is with an unchanged working conf file from RC7 (which, aside from comments, nothing has changed config-wise in the conf from version RC7).

Hi All, I have a thin cliente here that i want to run asterisk: - National Semicondudor Geode GX1 266MHz Geode 266MHz single chip - NS Cx5530a Southbridge National Semiconductors SC2200 - NS PC97317 in chipset - 32MB Compact Flash - 64MB Ram - 10/100Mbps, Autosense 10/100Mbps, Autosense Realtek 8139C National DP83815 / DP83816 Some tip? I have a ide>flash

Hi All, I have a Soekris 4801 running Asterisk and I tried to add a X100P FXO card only to find that the Soekris will not boot with the card installed. The LEDs flash for a second and then nothing, it does not boot. I've tried 2 different X100p cards, both of which work in a regular desktop system, and still have no luck. I tried a different Soekris 4801 with no luck. I've also tried a

Hello, Recently I have discovered a problem with serial console output when net-booting a Soekris net5501 board via pxe. When using pxelinux.0 from syslinux 4.04 package I get only 15 characters from the output, then the carriage returns back to the same line over and over again, making it impossible to read the output. What is more the booting process (trying configuration files with

Hi group, i'm brand new and i would like to ask about soekris hardware. I read along the web but i have some doubts that i think can be solved here. My question are the following: 1) does the Digium TDM400P fit in the soekris box with a 4801 SBC or a bigger box is needed? Any suggestions about where to pick up another box? 2) does the Digium TDM100P (already discontinued) fits fine in a

Hi. I am trying to use EXTLINUX 3.08 to boot a Soekris net4801 from a CompaqFlash card. BIOS reports the CF card as the first master harddisk. During boot/load the loader hangs after this output: EXTLINUX 3.08 2005-05-19 PXELINUX and LILO works fine on the same setup It this a general problem with Soekris/net4801 and EXTLINUX? Regards Johan Linn?r

On 06/10/2014 11:41 AM, Thomas Quinot wrote: > Dear all, > > I'm trying to boot a recent PXELINUX on a brand new Soekris net4501 > (comBIOS 1.33). This combination appears to not work out of the box... > > I see much advice floating around from a few years ago, hinting that > earlier versions of PXELINUX might have worked. However before resorting > to archaeology

Hi, I am still struggling with the E1 card!!!! Does anyone has some experience with sangoma E1 card? I have this card in soekris net 4801. First I was runnig it with deactivated DMA and I was receiving overruns (even with no channels in use). Then I enabled the DMA. Now I have the overruns only during a call. When I'm using more than one channel, the voice is stuttering and the delay is very

Dear all, I'm trying to boot a recent PXELINUX on a brand new Soekris net4501 (comBIOS 1.33). This combination appears to not work out of the box... I see much advice floating around from a few years ago, hinting that earlier versions of PXELINUX might have worked. However before resorting to archaeology I'd be interested in feedback from others who might have got through this. I

Hi, Wich mini Linux distribution do you recommend? My idea is to use Shorewall in a Soekris mother, with some mini Linux installed. Thanks and Best regards, Andrés

We found at the wiki a link to soekris and wonder if it is good? Is anybody using it and can share some experience, please? We would like to use it as a small PBX including a wireless access point, so that we can also use WiFi phones. bye Ronald

Hello, Freebsd-stable. I installed 7.1-STABLE on my new Soekris net5501. Kernel config is in attach. This unit lock up in strange way every day. It is pingable, but no access to host on any network protocol (sshd, named, etc are not answering), and serial console (only one this unit has) DOESN'T ANSWER too! Only way to un-freeze it is cold reboot. I've thought, it is

I thought I saw a Soekris embedded in the Digium booth photos, can you run Asterisk on one of these? How? I'd be interested in it for a back pbx, given the reliability. In fact, might want to move my home pbx to this also. Chris Mason